scholarly journals Cu-Doped TiO2: Visible Light Assisted Photocatalytic Antimicrobial Activity

2018 ◽  
Vol 8 (11) ◽  
pp. 2067 ◽  
Author(s):  
Snehamol Mathew ◽  
Priyanka Ganguly ◽  
Stephen Rhatigan ◽  
Vignesh Kumaravel ◽  
Ciara Byrne ◽  
...  
Keyword(s):  
Visible Light ◽  
Visible Light Irradiation ◽  
Density Functional ◽  
Anatase Phase ◽  
Sol Gel ◽  
Light Irradiation ◽  
Health Concern ◽  
Bacterial Inactivation ◽  
Doped Tio2 ◽  
X Ray

Surface contamination by microbes is a major public health concern. A damp environment is one of potential sources for microbe proliferation. Smart photocatalytic coatings on building surfaces using semiconductors like titania (TiO2) can effectively curb this growing threat. Metal-doped titania in anatase phase has been proven as a promising candidate for energy and environmental applications. In this present work, the antimicrobial efficacy of copper (Cu)-doped TiO2 (Cu-TiO2) was evaluated against Escherichia coli (Gram-negative) and Staphylococcus aureus (Gram-positive) under visible light irradiation. Doping of a minute fraction of Cu (0.5 mol %) in TiO2 was carried out via sol-gel technique. Cu-TiO2 further calcined at various temperatures (in the range of 500–700 °C) to evaluate the thermal stability of TiO2 anatase phase. The physico-chemical properties of the samples were characterized through X-ray diffraction (XRD), Raman spectroscopy, X-ray photo-electron spectroscopy (XPS) and UV–visible spectroscopy techniques. XRD results revealed that the anatase phase of TiO2 was maintained well, up to 650 °C, by the Cu dopant. UV–vis results suggested that the visible light absorption property of Cu-TiO2 was enhanced and the band gap is reduced to 2.8 eV. Density functional theory (DFT) studies emphasize the introduction of Cu+ and Cu2+ ions by replacing Ti4+ ions in the TiO2 lattice, creating oxygen vacancies. These further promoted the photocatalytic efficiency. A significantly high bacterial inactivation (99.9999%) was attained in 30 min of visible light irradiation by Cu-TiO2.

Cu Doped TiO2: Visible Light Assisted Photocatalytic Antimicrobial Activity and High Temperature Anatase Stability

2018 ◽  
Author(s):  
Snehamol Mathew ◽  
Priyanka Ganguly ◽  
Stephen Rhatigan ◽  
Vignesh Kumaravel ◽  
Ciara Byrne ◽  
...  
Keyword(s):  
Visible Light ◽  
Visible Light Irradiation ◽  
Density Functional ◽  
Anatase Phase ◽  
Sol Gel ◽  
Chemical Properties ◽  
Light Irradiation ◽  
Health Concern ◽  
Bacterial Inactivation ◽  
X Ray

Indoor surface contamination by microbes is a major public health concern. A damp environment is one potential sources for microbe proliferation. Smart photocatalytic coatings on building surfaces using semiconductors like titania (TiO<sub>2</sub>) can effectively curb this growing threat.<b> </b>Metal-doped titania in anatase phase has been proved as a promising candidate for energy and environmental applications. In this present work, the antimicrobial efficacy of copper (Cu) doped TiO<sub>2 </sub>(Cu-TiO<sub>2</sub>) was evaluated against <i>Escherichia coli</i> (Gram-negative) and <i>Staphylococcus aureus</i> (Gram-positive) under visible light irradiation. Doping of a minute fraction of Cu (0.5 mol %) in TiO<sub>2 </sub>was carried out <i>via</i> sol-gel technique. Cu-TiO<sub>2</sub> further calcined at various temperatures (in the range of 500 °C – 700 °C) to evaluate the thermal stability of TiO<sub>2</sub> anatase phase. The physico-chemical properties of the samples were characterised through X-ray diffraction (XRD), Raman spectroscopy, X-ray photo-electron spectroscopy (XPS) and UV-visible spectroscopy techniques. XRD results revealed that the anatase phase of TiO<sub>2</sub> was maintained well, up to 650 °C, by the Cu dopant. UV-DRS results suggested that the visible light absorption property of Cu-TiO<sub>2 </sub>was enhanced and the band gap is reduced to 2.8 eV. Density functional theory (DFT) studies emphasises the introduction of Cu<sup>+</sup> and Cu<sup>2+</sup> ions by replacing Ti<sup>4+</sup> ions in the TiO<sub>2</sub> lattice, creating oxygen vacancies. These further promoted the photocatalytic efficiency. A significantly high bacterial inactivation (99.9%) was attained in 30 mins of visible light irradiation by Cu-TiO<sub>2</sub>.

Cu Doped TiO2: Visible Light Assisted Photocatalytic Antimicrobial Activity and High Temperature Anatase Stability

2018 ◽  
Author(s):  
Snehamol Mathew ◽  
Priyanka Ganguly ◽  
Stephen Rhatigan ◽  
Vignesh Kumaravel ◽  
Ciara Byrne ◽  
...  
Keyword(s):  
Visible Light ◽  
Visible Light Irradiation ◽  
Density Functional ◽  
Anatase Phase ◽  
Sol Gel ◽  
Chemical Properties ◽  
Light Irradiation ◽  
Health Concern ◽  
Bacterial Inactivation ◽  
X Ray

Indoor surface contamination by microbes is a major public health concern. A damp environment is one potential sources for microbe proliferation. Smart photocatalytic coatings on building surfaces using semiconductors like titania (TiO<sub>2</sub>) can effectively curb this growing threat.<b> </b>Metal-doped titania in anatase phase has been proved as a promising candidate for energy and environmental applications. In this present work, the antimicrobial efficacy of copper (Cu) doped TiO<sub>2 </sub>(Cu-TiO<sub>2</sub>) was evaluated against <i>Escherichia coli</i> (Gram-negative) and <i>Staphylococcus aureus</i> (Gram-positive) under visible light irradiation. Doping of a minute fraction of Cu (0.5 mol %) in TiO<sub>2 </sub>was carried out <i>via</i> sol-gel technique. Cu-TiO<sub>2</sub> further calcined at various temperatures (in the range of 500 °C – 700 °C) to evaluate the thermal stability of TiO<sub>2</sub> anatase phase. The physico-chemical properties of the samples were characterised through X-ray diffraction (XRD), Raman spectroscopy, X-ray photo-electron spectroscopy (XPS) and UV-visible spectroscopy techniques. XRD results revealed that the anatase phase of TiO<sub>2</sub> was maintained well, up to 650 °C, by the Cu dopant. UV-DRS results suggested that the visible light absorption property of Cu-TiO<sub>2 </sub>was enhanced and the band gap is reduced to 2.8 eV. Density functional theory (DFT) studies emphasises the introduction of Cu<sup>+</sup> and Cu<sup>2+</sup> ions by replacing Ti<sup>4+</sup> ions in the TiO<sub>2</sub> lattice, creating oxygen vacancies. These further promoted the photocatalytic efficiency. A significantly high bacterial inactivation (99.9%) was attained in 30 mins of visible light irradiation by Cu-TiO<sub>2</sub>.

scholarly journals Development of Smart Composites Based on Doped-TiO2 Nanoparticles with Visible Light Anticancer Properties

Materials ◽  
2019 ◽  
Vol 12 (16) ◽  
pp. 2589 ◽  
Author(s):  
Evdokia Galata ◽  
Eleni A. Georgakopoulou ◽  
Maria-Emmanouela Kassalia ◽  
Nefeli Papadopoulou-Fermeli ◽  
Evangelia A. Pavlatou
Keyword(s):  
Visible Light ◽  
Tio2 Nanoparticles ◽  
Visible Light Irradiation ◽  
Sol Gel ◽  
Ultra Violet ◽  
Light Irradiation ◽  
Composite Particles ◽  
Doped Tio2 ◽  
X Ray ◽  
Anticancer Properties

In this study, the synthesis of smart, polymerically embedded titanium dioxide (TiO2) nanoparticles aimed to exhibit photo-induced anticancer properties under visible light irradiation is investigated. The TiO2 nanoparticles were prepared by utilizing the sol gel method with different dopants, including nitrogen (N-doped), iron (Fe-doped), and nitrogen and iron (Fe,N-doped). The dopants were embedded in an interpenetrating (IP) network microgel synthesized by stimuli responsive poly (N-Isopropylacrylamide-co-polyacrylicacid)–pNipam-co-PAA forming composite particles. All the types of produced particles were characterized by X-ray powder diffraction, micro-Raman, Fourier-transform infrared, X-ray photoelectron, ultra-violet-visible spectroscopy, Field Emission Scanning Electron, Transmission Electron microscopy, and Dynamic Light Scattering techniques. The experimental findings indicate that the doped TiO2 nanoparticles were successfully embedded in the microgel. The N-doped TiO2 nano-powders and composite particles exhibit the best photocatalytic degradation of the pollutant methylene blue under visible light irradiation. Similarly, the highly malignant MDA-MB-231 breast cancer epithelial cells were susceptible to the inhibition of cell proliferation at visible light, especially in the presence of N-doped powders and composites, compared to the non-metastatic MCF-7 cells, which were not affected.

scholarly journals Photocatalytic Antibacterial Effectiveness of Cu-Doped TiO2 Thin Film Prepared via the Peroxo Sol-Gel Method

Catalysts ◽  
2018 ◽  
Vol 8 (9) ◽  
pp. 352 ◽  
Author(s):  
Benjawan Moongraksathum ◽  
Jun-Ya Shang ◽  
Yu-Wen Chen
Keyword(s):  
Electron Microscopy ◽  
Methylene Blue ◽  
Visible Light ◽  
Visible Light Irradiation ◽  
Sol Gel ◽  
Light Irradiation ◽  
Gel Method ◽  
Doped Tio2 ◽  
X Ray ◽  
Photocatalytic Activities

Cu-doped titanium dioxide thin films (Cu/TiO2) were prepared on glass substrate via peroxo sol-gel method and dip-coating process with no subsequent calcination process for the degradation of organic dye and use as an antibacterial agent. The as-prepared materials were characterised using transmission electron microscopy (TEM), X-ray diffraction (XRD), scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). For photocatalytic degradation of methylene blue in water, the samples were subjected to Ultraviolet C (UVC) and visible light irradiation. Degraded methylene blue concentration was measured using UV-Vis spectrophotometer. The antibacterial activities of the samples were tested against the gram-negative bacteria Escherichia coli (ATCC25922). Copper species were present in the form of CuO on the surface of modified TiO2 particles, which was confirmed using TEM and XPS. The optimal observed Cu/TiO2 weight ratio of 0.5 represents the highest photocatalytic activities under both UVC and visible light irradiation. Moreover, the same composition remarkably exhibited high antibacterial effectiveness against E. coli after illumination with ultraviolet A. The presence of CuO on TiO2 significantly enhanced photocatalytic activities. Therefore, active Cu-doped TiO2 can be used as a multipurpose coating material.

scholarly journals Synthesis of C,N,S-tridoped TiO2 distribute onto silicone for photocatalytic on degradation of tetracycline under visible light irradiation

2021 ◽  
Vol 10 (1) ◽  
pp. 1-7
Author(s):  
Thuy Le Thi Thanh ◽  
Tung Huynh Thanh ◽  
Hung Nguyen Phi
Keyword(s):  
Visible Light ◽  
Visible Light Irradiation ◽  
Light Irradiation ◽  
Optimum Dose ◽  
Titanyl Sulfate ◽  
Isothermal Adsorption ◽  
Photocatalytic Ability ◽  
Doped Tio2 ◽  
X Ray ◽  
Co Doped

Using carbon, nitrogen, and sulfur sourced from thiourea to co-doped TiO2 (C,N,S-TiO2), was prepared via hydrothermal method using precursors of titanyl sulfate TiOSO4, obtained by decomposition of ilmenite ore in Binh Dinh. The material used to make the substrate is glass and distributed onto it is silicone and photocatalytic. The structure and properties of materials system were investigated by modern physicochemical analysis methods including scanning electron microscope (SEM), X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectra, diffuse reflection spectroscopy UV-Vis, transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDX) and nitrogen isothermal adsorption. The photocatalytic ability of materials system after being carried by silicone is demonstrated by decomposing tetracycline (10 mg/L) in aqueous solution with the yield more than 88% efficiency after 6 hours under visible light irradiation. The optimum dose of the photocatalyst was 0.6 g/L under visible light irradiation. The results indicated that C, N, S co-doped TiO2 demonstrated the highest photocatalytic efficiency and a perspective recyclable potential when it is distributed onto silicone.

scholarly journals Sol-Gel Synthesized N and MN Co-Doped Tio2 Nanomaterial for Photocatalytic Degradation of Malathion under Visible Light Irradiation

2019 ◽  
Vol 9 (2) ◽  
pp. 3688-3694
Keyword(s):  
Visible Light ◽  
Photocatalytic Degradation ◽  
Visible Light Irradiation ◽  
Sol Gel ◽  
Light Irradiation ◽  
Average Particle ◽  
Doped Tio2 ◽  
Sem And Tem ◽  
Ft Ir ◽  
Co Doped

Different weight percentages (0.25-1.00 wt%) of Nitrogen (Non-Metal) and Manganese (Metal) co-doped nano titania were synthesized by sol-gel method and characterized by XRD, UV-vis.DRS, FT-IR, XPS, SEM and TEM. The XRD results has shown that all the prepared catalysts are in anatase phase indicating that co-doping of N and Mn did not affect the crystal structure of TiO2 . From the UV-vis.DRS spectra a significant absorption shift towards visible region was noticed in N and Mn co-doped TiO2 and their presence was confirmed by XPS and FT-IR results. SEM and TEM results showed spherical nanoparticles with average particle size of 9 nm. Photocatalytic efficiency of synthesized nano materials was tested on non-biodegradable organophosphorous pesticide, Malathion under visible light irradiation. The effect of dopant concentration, pH, catalyst dosage, and initial pesticide concentration on photocatalytic degradation of malathion was studied and optimum conditions were established. Among the synthesized samples 0.50 wt% N & 1.00 wt% Mn-TiO2 exhibited best photocatalytic performance. Photoluminiscent spectroscopy (PL) was used to examine the rate of production of oxidative species, hydroxyl radicals which play key role in photocatalytic degradation.

scholarly journals Fe-doped TiO2/Kaolinite as an Antibacterial Photocatalyst under Visible Light Irradiation

2021 ◽  
Vol 16 (2) ◽  
pp. 293-301
Author(s):  
Anthoni B. Aritonang ◽  
Eka Pratiwi ◽  
Warsidah Warsidah ◽  
S. I. Nurdiansyah ◽  
R. Risko
Keyword(s):  
Visible Light ◽  
Band Gap ◽  
Visible Light Irradiation ◽  
Sol Gel ◽  
Light Irradiation ◽  
Wave Number ◽  
Crystal Lattices ◽  
Doped Tio2 ◽  
Tio2 Lattice ◽  
Kaolinite Surface

In this work, undoped and Fe-doped TiO2 immobilized on kaolinite surface was successfully synthesized by sol-gel method with various Fe concentrations (0.05, 0.125, and 0.25 wt%). The effects of Fe doping into TiO2 lattice were thoroughly investigated by a diffuse reflectance UV-visible (DRS) spectroscopy, Fourier Transform Infrared (FTIR) spectroscopy, and X-ray diffraction (XRD). The optical band gap of undoped and Fe-doped TiO2/kaolinite is red shifted with respect to the incorporation of Fe3+ into the structure of TiO2 resulted band gap. The FTIR spectra shows a shift of peak at the wave number at 586 cm−1 and 774 cm−1 which is attribute of the Fe−O vibration as an indication of the formation of Fe-TiO2 bonds. Incorporation of Fe3+ cation into the TiO2 lattice replacing the Ti4+ ions, which induced a perturbation in anatase crystal structure, causes the change in the distance spacing of the crystal lattices dhkl(101) of 8.9632 to 7.9413. The enhanced photocatalytic performance was observed for Fe-doped TiO2/kaolinite compared with TiO2/kaolinite with respect to Escherichia coli growth inhibition in solution media under visible light irradiation. Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0).  

Preparation and Characterization of Nitrogen Doped TiO2 Nanoparticles as an Effective Catalyst in Photodegradation of Phenol under Visible Light

2014 ◽  
Vol 875-877 ◽  
pp. 28-33 ◽  
Author(s):  
Armineh Hassanvand ◽  
Morteza Sohrabi ◽  
Sayed Javid Royaee ◽  
Morteza Jafarikajour
Keyword(s):  
Visible Light ◽  
Tio2 Nanoparticles ◽  
Surface Area ◽  
Visible Light Irradiation ◽  
Light Irradiation ◽  
Bet Surface Area ◽  
Doped Tio2 ◽  
X Ray ◽  
Nitrogen Doped ◽  
Degussa P25

Nitrogen-doped TiO2 nanoparticles of commercial Degussa P25 have been prepared via a direct impregnation reaction using ammonium hydroxide solution as nitrogen source. The Samples were characterized by X-ray diffraction (XRD), BET surface area BJH pore charecterization and scanning electron microscopy (SEM) equipped with energy dispersive X-ray spectroscopy (EDX). The results demonstrated that the nitrogen-doped TiO2 nanoparticles had a crystallite size 70.8 nm and a specific surface area of 6.4 m2/g with average pore diameter of 23.3 nm consisting mainly of titanium and oxygen. The photocatalyst activity was determined by degradation of phenol in an impinging stream reactor under visible light irradiation (λ> 400 nm). N-TiO2 catalyst exhibited higher photocatalytic activity in comparison with Degussa P25 under visible light irradiation.

scholarly journals Enhanced Photoactivity of Fe + N Codoped Anatase-RutileTiO2Nanowire Film under Visible Light Irradiation

2012 ◽  
Vol 2012 ◽  
pp. 1-8 ◽  
Author(s):  
Kewei Li ◽  
Haiying Wang ◽  
Chunxu Pan ◽  
Jianhong Wei ◽  
Rui Xiong ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Visible Light ◽  
Visible Light Irradiation ◽  
Photoelectron Spectroscopy ◽  
Synergistic Effects ◽  
Anatase Phase ◽  
Light Irradiation ◽  
Codoped Sample ◽  
X Ray ◽  
Photocatalytic Activities

Rutile-anatase phase mixedFe+Ncodoped TiO2nanowires were designed and prepared by a two-step anodic oxidation method. The results of X-ray diffraction, scanning electron microscopy, and high-resolution transmission electron microscopy confirm that the preparedFe+Ncodoped TiO2nanowires exhibit intimately contacted anatase-rutile heterostructure with the rutile content of 21.89%. The X-ray photoelectron spectroscopy measurements show that nitrogen and iron atoms are incorporated into the titania oxide lattice, and the UV-visible absorption spectra show that the codoping of iron and nitrogen atoms could extend the absorption to visible light region. The photocatalytic activities of all the samples were evaluated by photocatalytic degradation of methylene blue under visible light irradiation. TheFe+Ncodoped sample achieves the best response to visible light and the highest photocatalytic activities. The enhancement of photocatalytic activity forFe+Ncodoped sample should be ascribed to the synergistic effects of codoped nitrogen and iron ions and the anatase-rutile heterostructure.

Sign in / Sign up

Export Citation Format

Share Document