scholarly journals Probabilistic Characteristics of Moment Capacity and Rotational Stiffness of Wedge Joints Used in Support Systems Reflecting Reused Members

2019 ◽  
Vol 9 (19) ◽  
pp. 4056 ◽  
Author(s):  
Jin Kyun Bong ◽  
Hyung Do Lee ◽  
Seungjun Kim ◽  
Ho-Seong Mha ◽  
Dong-Kyun Yim ◽  
...  
Keyword(s):  
Confidence Interval ◽  
Lower Limit ◽  
Support Systems ◽  
Rotational Stiffness ◽  
New Members ◽  
Moment Capacity ◽  
Upper Limit ◽  
Upper Limits ◽  
Trilinear Model ◽  
The Moment

The moment capacity and rotational stiffness of wedge joints, which connect vertical and horizontal members of assembled support systems, were evaluated experimentally considering the characteristics of reused members. Since temporary structures, such as supports, tend to be reused, experiments were conducted with reused members, and the normality of the measured data was assessed. The lower and upper limits of the 95% confidence intervals of the moment capacity and rotational stiffness of wedge joints with reused members were determined. Experiments were also conducted on a joint system with new members to analyze the influence of reused members. In integrating both new and reused members, the maximum moments of wedge joints were observed to be normally distributed. The lower limit of the 95% confidence interval of the maximum moment of joints was 0.997 kNm, and the upper limit was 1.074 kNm. The rotational stiffness of the wedge joint was evaluated using a trilinear model. The initial rotational stiffness decreased with continued use of the joint. The average rotational stiffness of the joint, analyzed by combining the results for new and reused members, was found to be 22.475 kNm/rad for the first interval, 4.705 kNm/rad for the second interval, and 1.577 kNm/rad for the third interval. The lower limit of the 95% confidence interval of the initial rotational stiffness was 20.688 kNm/rad, and the upper limit was 24.262 kNm/rad.

Experimental study of moment carrying behavior of typical Tibetan timber beam-column joints

2021 ◽  
pp. 136943322110015
Author(s):  
Ting Guo ◽  
Na Yang ◽  
Huichun Yan ◽  
Fan Bai
Keyword(s):  
Bending Moment ◽  
Structural Performance ◽  
Test Results ◽  
Timber Beam ◽  
Rotational Stiffness ◽  
Trilinear Model ◽  
Column Joint ◽  
Loading Tests ◽  
The Moment ◽  
Relationship Of

This study aimed to investigate the moment carrying behavior of typical Tibetan timber beam-column joints under monotonic vertical static load and also evaluate the influence of length ratio of Gongmu to beam (LRGB) and dowels layout on the structural performance of the joint. Six full-scale specimens were fabricated with same construction but different Gongmu length and dowels position. The moment carrying performance of beam-column joints in terms of failure mode, moment resistance, and rotational stiffness of joints were obtained via monotonic loading tests. Test results indicated that all joints are characterized by compressive failure perpendicular to grain of Ludou. Additionally, it was found that greater LRGB leads to greater initial rotational stiffness and maximum moment of the joint by an increase of restraint length for beam end; however, offsetting dowels toward column resulted smaller stiffness and ultimate bending moment of joints, particularly, offsetting Beam-Gongmu dowels toward column changed the moment-rotation curve pattern of the beam-column joint, accompanied by a hardening stiffness at last phase. Furthermore, a simplified trilinear model was proposed to represent the moment-rotation relationship of the typical Tibetan timber beam-column joint.

scholarly journals Non-contact infrared thermometers compared with current approaches in primary care for children aged 5 years and under: a method comparison study

2020 ◽  
Vol 24 (53) ◽  
pp. 1-28 ◽  
Author(s):  
Ann Van den Bruel ◽  
Jan Verbakel ◽  
Kay Wang ◽  
Susannah Fleming ◽  
Gea Holtman ◽  
...  
Keyword(s):  
Primary Care ◽  
Confidence Interval ◽  
Lower Limit ◽  
Method Comparison ◽  
Health Technology ◽  
Comparison Study ◽  
Infrared Thermometer ◽  
Upper Limit ◽  
The Difference ◽  
Method Comparison Study

Background Current options for temperature measurement in children presenting to primary care include either electronic axillary or infrared tympanic thermometers. Non-contact infrared thermometers could reduce both the distress of the child and the risk of cross-infection. Objectives The objective of this study was to compare the use of non-contact thermometers with the use of electronic axillary and infrared tympanic thermometers in children presenting to primary care. Design Method comparison study with a nested qualitative study. Setting Primary care in Oxfordshire. Participants Children aged ≤ 5 years attending with an acute illness. Interventions Two types of non-contact infrared thermometers [i.e. Thermofocus (Tecnimed, Varese, Italy) and Firhealth (Firhealth, Shenzhen, China)] were compared with an electronic axillary thermometer and an infrared tympanic thermometer. Main outcome measures The primary outcome was agreement between the Thermofocus non-contact infrared thermometer and the axillary thermometer. Secondary outcomes included agreement between all other sets of thermometers, diagnostic accuracy for detecting fever, parental and child ratings of acceptability and discomfort, and themes arising from our qualitative interviews with parents. Results A total of 401 children (203 boys) were recruited, with a median age of 1.6 years (interquartile range 0.79–3.38 years). The readings of the Thermofocus non-contact infrared thermometer differed from those of the axillary thermometer by –0.14 °C (95% confidence interval –0.21 to –0.06 °C) on average with the lower limit of agreement being –1.57 °C (95% confidence interval –1.69 to –1.44 °C) and the upper limit being 1.29 °C (95% confidence interval 1.16 to 1.42 °C). The readings of the Firhealth non-contact infrared thermometer differed from those of the axillary thermometer by –0.16 °C (95% confidence interval –0.23 to –0.09 °C) on average, with the lower limit of agreement being –1.54 °C (95% confidence interval –1.66 to –1.41 °C) and the upper limit being 1.22 °C (95% confidence interval 1.10 to 1.34 °C). The difference between the first and second readings of the Thermofocus was –0.04 °C (95% confidence interval –0.07 to –0.01 °C); the lower limit was –0.56 °C (95% confidence interval –0.60 to –0.51 °C) and the upper limit was 0.47 °C (95% confidence interval 0.43 to 0.52 °C). The difference between the first and second readings of the Firhealth thermometer was 0.01 °C (95% confidence interval –0.02 to 0.04 °C); the lower limit was –0.60 °C (95% confidence interval –0.65 to –0.54 °C) and the upper limit was 0.61 °C (95% confidence interval 0.56 to 0.67 °C). Sensitivity and specificity for the Thermofocus non-contact infrared thermometer were 66.7% (95% confidence interval 38.4% to 88.2%) and 98.0% (95% confidence interval 96.0% to 99.2%), respectively. For the Firhealth non-contact infrared thermometer, sensitivity was 12.5% (95% confidence interval 1.6% to 38.3%) and specificity was 99.4% (95% confidence interval 98.0% to 99.9%). The majority of parents found all methods to be acceptable, although discomfort ratings were highest for the axillary thermometer. The non-contact thermometers required fewer readings than the comparator thermometers. Limitations A method comparison study does not compare new methods against a reference standard, which in this case would be central thermometry requiring the placement of a central line, which is not feasible or acceptable in primary care. Electronic axillary and infrared tympanic thermometers have been found to have moderate agreement themselves with central temperature measurements. Conclusions The 95% limits of agreement are > 1 °C for both non-contact infrared thermometers compared with electronic axillary and infrared tympanic thermometers, which could affect clinical decision-making. Sensitivity for fever was low to moderate for both non-contact thermometers. Future work Better methods for peripheral temperature measurement that agree well with central thermometry are needed. Trial registration Current Controlled Trials ISRCTN15413321. Funding This project was funded by the National Institute for Health Research (NIHR) Health Technology Assessment programme and will be published in full in Health Technology Assessment; Vol. 24, No. 53. See the NIHR Journals Library website for further project information.

scholarly journals Short gamma-ray bursts within 200 Mpc

2020 ◽  
Vol 492 (4) ◽  
pp. 5011-5022 ◽  
Author(s):  
S Dichiara ◽  
E Troja ◽  
B O’Connor ◽  
F E Marshall ◽  
P Beniamini ◽  
...  
Keyword(s):  
Confidence Interval ◽  
Gamma Ray ◽  
Gamma Ray Bursts ◽  
Local Universe ◽  
X Ray ◽  
Upper Limit ◽  
Upper Limits ◽  
Nearby Galaxies ◽  
The One ◽  
Short Grbs

ABSTRACT We present a systematic search for short-duration gamma-ray bursts (GRBs) in the local Universe based on 14 yr of observations with the Neil Gehrels Swift Observatory. We cross-correlate the GRB positions with the GLADE catalogue of nearby galaxies, and find no event at a distance ≲100 Mpc and four plausible candidates in the range 100 Mpc ≲ D ≲ 200 Mpc. Although affected by low statistics, this number is higher than the one expected for chance alignments to random galaxies, and possibly suggests a physical association between these bursts and nearby galaxies. By assuming a local origin, we use these events to constrain the range of properties for X-ray counterparts of neutron star mergers. Optical upper limits place tight constraints on the onset of a blue kilonova, and imply either low masses ($\lesssim 10^{-3}\, \mathrm{M}_{\odot }$) of lanthanide-poor ejecta or unfavorable orientations (θobs ≳ 30 deg). Finally, we derive that the all-sky rate of detectable short GRBs within 200 Mpc is $1.3^{+1.7}_{-0.8}$ yr−1 (68 per cent confidence interval), and discuss the implications for the GRB outflow structure. If these candidates are instead of cosmological origin, we set a upper limit of ≲2.0 yr−1 (90 per cent confidence interval) to the rate of nearby events detectable with operating gamma-ray observatories, such as Swift and Fermi.

Vitamin-A-Exzess durch Pferdefleischprodukte mit hohen Leberanteilen

2013 ◽  
Vol 41 (01) ◽  
pp. 31-36
Author(s):  
E. Kienzle ◽  
N. Becker
Keyword(s):  
Vitamin A ◽  
Eine Analyse ◽  
Upper Limit ◽  
Upper Limits

ZusammenfassungIm Rahmen einer Eliminationsdiät wird regelmäßig Pferdefleisch eingesetzt. Aus Gründen der Praktikabilität verwenden Tierbesitzer häufig kommerziell erhältliches Pferdefleisch aus der Dose. Aufgrund eines Berichts von Zervikalspondylosen bei einer auf Futtermittel allergischen Katze erfolgte eine Analyse verschiedener auf Pferdefleisch basierender Produkte hinsichtlich des Vitamin-AGehalts.In 14 Pferdefleischerzeugnissen wurde der Vitamin-A-Gehalt (Retinol) analysiert. Der Gehalt an umsetzbarer Energie wurde mithilfe von Schätzformeln auf Basis der Deklaration berechnet.In Produkten mit deklarierten Anteilen von Leber, Innereien oder tierischen Nebenprodukten konnten zum Teil erhebliche Vitamin-A-Gehalte festgestellt werden. Bei alleiniger Verfütterung eines dieser Produkte (Deckung des durchschnittlichen Energiebedarfs) würde die Vitamin-A-Versorgung nur knapp unter dem Safe Upper Limit der Katze sowie oberhalb des Safe Upper Limits beim Hund liegen.Bei All-Meat-Produkten sollte nicht nur die Deklaration, sondern auch der Inhalt näher betrachtet werden, um einen Hinweis auf eventuell hohe Leberanteile zu erhalten.Aufgrund der Ergebnisse ist eine exzessive Vitamin-A-Aufnahme bei langfristiger Verfütterung von Pferdefleischprodukten mit hohen Leberanteilen nicht auszuschließen.

Flexural Resistance of Steel-Coconut Shell Concrete-Steel Composite Beam with Normal and J-Hook Shear Studs

2020 ◽  
Vol 12 (9) ◽  
Author(s):  
Lakshmi Thangasamy ◽  
◽  
Gunasekaran Kandasamy ◽  
Keyword(s):  
Concrete Strength ◽  
Steel Plates ◽  
Coconut Shell ◽  
Core Material ◽  
River Sand ◽  
Concrete Core ◽  
Conventional Concrete ◽  
Moment Capacity ◽  
The Moment ◽  
Core Concrete

Many researches on double skin sandwich having top and bottom steel plates and in between concrete core called as steel-concrete-steel (SCS) were carried out by them on this SCS type using with different materials. Yet, use of coconut shell concrete (CSC) as a core material on this SCS form construction and their results are very limited. Study investigated to use j-hook shear studs under flexure in the concept of steel-concrete-steel (SCS) in which the core concrete was CSC. To compare the results of CSC, the conventional concrete (CC) was also considered. To study the effect of quarry dust (QD) in its place of river sand (RS) was also taken. Hence four different mixes two without QD and two with QD both in CC and CSC was considered. The problem statement is to examine about partial and fully composite, moment capacity, deflection and ductility properties of CSC used SCS form of construction. Core concrete strength and the j-hook shear studs used are influences the moment carrying capacity of the SCS beams. Use of QD in its place of RS enhances the strength of concrete produced. Deflections predicted theoretically were compared with experimental results. The SCS beams showed good ductility behavior.

PNN and BP Neural Network Fault Diagnosis Research on Electronic Accelerator Pedal Detection

2020 ◽  
Vol 14 (2) ◽  
pp. 205-220
Author(s):  
Yuxiu Jiang ◽  
Xiaohuan Zhao
Keyword(s):  
Neural Network ◽  
Fault Diagnosis ◽  
Fault Detection ◽  
Lower Limit ◽  
Bp Neural Network ◽  
Accelerator Pedal ◽  
Electronic Throttle ◽  
Measured Voltage ◽  
Upper Limit ◽  
Network Fault

Background: The working state of electronic accelerator pedal directly affects the safety of vehicles and drivers. Effective fault detection and judgment for the working state of the accelerator pedal can prevent accidents. Methods: Aiming at different working conditions of electronic accelerator pedal, this paper used PNN and BP diagnosis model to detect the state of electronic accelerator pedal according to the principle and characteristics of PNN and BP neural network. The fault diagnosis test experiment of electronic accelerator pedal was carried out to get the data acquisition. Results: After the patents for electronic accelerator pedals are queried and used, the first measured voltage, the upper limit of first voltage, the first voltage lower limit, the second measured voltage, the upper limit of second voltage and the second voltage lower limit are tested to build up the data samples. Then the PNN and BP fault diagnosis models of electronic accelerator pedal are established. Six fault samples are defined through the design of electronic accelerator pedal fault classifier and the fault diagnosis processes are executed to test. Conclusion: The fault diagnosis results were analyzed and the comparisons between the PNN and the BP research results show that BP neural network is an effective method for fault detection of electronic throttle pedal, which is obviously superior to PNN neural network based on the experiment data.

scholarly journals Search for π0 decays to invisible particles

2021 ◽  
Vol 2021 (2) ◽  
Author(s):  
E. Cortina Gil ◽  
◽  
A. Kleimenova ◽  
E. Minucci ◽  
S. Padolski ◽  
...  
Keyword(s):  
Higgs Boson ◽  
Standard Model ◽  
Confidence Level ◽  
Branching Ratio ◽  
Standard Model Higgs Boson ◽  
Scalar Mixing ◽  
Upper Limit ◽  
Upper Limits ◽  
The Standard Model ◽  
Model Independent

Abstract The NA62 experiment at the CERN SPS reports a study of a sample of 4 × 109 tagged π0 mesons from K+ → π+π0(γ), searching for the decay of the π0 to invisible particles. No signal is observed in excess of the expected background fluctuations. An upper limit of 4.4 × 10−9 is set on the branching ratio at 90% confidence level, improving on previous results by a factor of 60. This result can also be interpreted as a model- independent upper limit on the branching ratio for the decay K+ → π+X, where X is a particle escaping detection with mass in the range 0.110–0.155 GeV/c2 and rest lifetime greater than 100 ps. Model-dependent upper limits are obtained assuming X to be an axion-like particle with dominant fermion couplings or a dark scalar mixing with the Standard Model Higgs boson.

scholarly journals Upper limits on the extent of seafloor anoxia during the PETM from uranium isotopes

2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Matthew O. Clarkson ◽  
Timothy M. Lenton ◽  
Morten B. Andersen ◽  
Marie-Laure Bagard ◽  
Alexander J. Dickson ◽  
...  
Keyword(s):  
Carbon Cycle ◽  
Global Scale ◽  
Uranium Isotopes ◽  
Biogeochemical Model ◽  
Emission Scenarios ◽  
Isotope Data ◽  
Upper Limit ◽  
Thermal Maximum ◽  
Upper Limits ◽  
Anoxic Events

AbstractThe Paleocene Eocene Thermal Maximum (PETM) represents a major carbon cycle and climate perturbation that was associated with ocean de-oxygenation, in a qualitatively similar manner to the more extensive Mesozoic Oceanic Anoxic Events. Although indicators of ocean de-oxygenation are common for the PETM, and linked to biotic turnover, the global extent and temporal progression of de-oxygenation is poorly constrained. Here we present carbonate associated uranium isotope data for the PETM. A lack of resolvable perturbation to the U-cycle during the event suggests a limited expansion of seafloor anoxia on a global scale. We use this result, in conjunction with a biogeochemical model, to set an upper limit on the extent of global seafloor de-oxygenation. The model suggests that the new U isotope data, whilst also being consistent with plausible carbon emission scenarios and observations of carbon cycle recovery, permit a maximum ~10-fold expansion of anoxia, covering <2% of seafloor area.

The Excavation of Eighteen Round Barrows near Shrewton, Wiltshire.

1984 ◽  
Vol 50 ◽  
pp. 255-318 ◽  
Author(s):  
Charles Green ◽  
Stephen Rollo-Smith ◽  
Elisabeth Crowfoot ◽  
Calvin Wells
Keyword(s):  
Water Supply ◽  
Lower Limit ◽  
Open Water ◽  
Linear Groups ◽  
Upper Limit ◽  
The Village

The excavation of eighteen round barrows was undertaken by the late Charles Green during summer seasons from 1958 to 1960, in advance of their destruction by ploughing. The excavated barrows are members of two linear groups which occupy adjacent spurs to the east of the village of Shrewton in the modern parish of that name (fig. 1). One of the barrows investigated lies in Winterbourne Stoke parish. This western part of Salisbury Plain is termed the ‘Lower Plain’ comprising those areas having their ‘upper limit… between 400 and 450 feet OD and their lower limit where they overlook the valley trenches … between 250 and 300 feet O.D.’ (Gifford 1957, 6). In such a lower valley lie the modern villages of Shrewton and Rollestone, and through it flows the river Till, the nearest modern open water supply to the barrows. This connects the area to the River Avon via the Wylye and Nadder.

Sign in / Sign up

Export Citation Format

Share Document