scholarly journals Design and Experimental Verification of a PZT Pump with Streamlined Flow Tubes

2019 ◽  
Vol 9 (18) ◽  
pp. 3881 ◽  
Author(s):  
Ming Tang ◽  
Qibo Bao ◽  
Jianhui Zhang ◽  
Qingshuang Ning ◽  
Chaobin Chen ◽  
...  
Keyword(s):  
Flow Rate ◽  
Flow Resistance ◽  
Maximum Amplitude ◽  
Maximum Flow ◽  
Flow Stability ◽  
Rate Equations ◽  
Flow Tube ◽  
Piezoelectric Pump ◽  
Streamlined Flow ◽  
Frequency Relationship

In this paper, a streamlined flow tube valveless piezoelectric pump (SLFT PZT pump) is proposed to modify the single flow trend and improve the fluid flow stability. Firstly, the structural and working principle of the streamlined flow tube, which accounts for changing the flow trend and improving the flow stability, were analyzed. The flow resistance and flow rate equations were established. Secondly, the pressure and velocity fields of the tube were simulated. These simulated results were consistent with the theoretical results. Thirdly, the flow resistance of the flow tube was tested with pressure differences of 1000 Pa, 1200 Pa, 1400 Pa and 1600 Pa respectively. The trend of the result curves was consistent with the simulated results. The amplitude-frequency relationship and the flow-rate-frequency relationship were also tested, both result curves highly corelate. The maximum amplitude was 0.228 mm (10 Hz, 120 V), and the maximum flow rate was 17.01 mL/min (10 Hz, 100 V). Finally, the theoretical flow rate of the SLFT PZT pump was calculated at 100 V and 120 V. These results roughly fitted with the experimental results. The streamlined flow tube could change the internal flow trend that remarkably improved the flow stability. Therefore, it promoted the application of the valveless PZT pump in living cells, biomedical and polymer delivery.

scholarly journals Improving Output Performance of a Resonant Piezoelectric Pump by Adding Proof Masses to a U-Shaped Piezoelectric Resonator

Micromachines ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 500
Author(s):  
Jian Chen ◽  
Wenzhi Gao ◽  
Changhai Liu ◽  
Liangguo He ◽  
Yishan Zeng
Keyword(s):  
Flow Rate ◽  
Maximum Flow ◽  
Working Fluid ◽  
Driving Voltage ◽  
Piezoelectric Resonator ◽  
Piezoelectric Pump ◽  
Compact Structure ◽  
Output Performance ◽  
Volume Efficiency ◽  
Working Efficiency

This study proposes the improvement of the output performance of a resonant piezoelectric pump by adding proof masses to the free ends of the prongs of a U-shaped piezoelectric resonator. Simulation analyses show that the out-of-phase resonant frequency of the developed resonator can be tuned more efficiently within a more compact structure to the optimal operating frequency of the check valves by adjusting the thickness of the proof masses, which ensures that both the resonator and the check valves can operate at the best condition in a piezoelectric pump. A separable prototype piezoelectric pump composed of the proposed resonator and two diaphragm pumps was designed and fabricated with outline dimensions of 30 mm × 37 mm × 54 mm. Experimental results demonstrate remarkable improvements in the output performance and working efficiency of the piezoelectric pump. With the working fluid of liquid water and under a sinusoidal driving voltage of 298.5 Vpp, the miniature pump can achieve the maximum flow rate of 2258.9 mL/min with the highest volume efficiency of 77.1% and power consumption of 2.12 W under zero backpressure at 311/312 Hz, and the highest backpressure of 157.3 kPa under zero flow rate at 383 Hz.

The characters exploration of a piezoelectric pump with fishtail-shaped bluffbody

2021 ◽  
pp. 1045389X2110386
Author(s):  
Yi Hou ◽  
Lipeng He ◽  
Zheng Zhang ◽  
Baojun Yu ◽  
Hong Jiang ◽  
...  
Keyword(s):  
Flow Rate ◽  
Preliminary Investigation ◽  
Maximum Flow ◽  
Theoretical Explanation ◽  
Maximum Flow Rate ◽  
Bluff Bodies ◽  
Conical Flow ◽  
Piezoelectric Pump ◽  
Valveless Piezoelectric Pump ◽  
Shape And Size

This paper focuses on a new structure in the valveless piezoelectric pump, which has a combination structure of the conical flow channel and two fishtail-shaped bluffbodies in the chamber of the pump. The fishtail-shaped bluffbody is inspired by the shape of the swimming fish to diminish the backflow and optimize the performance of the pump. The performance is studied by changing the shape and size of the inlet and outlet, the bluff bodies’ height and the space between two bluff bodies. The results show that the 3 mm × 3 mm square inlet, 3 mm diameter round outlet, 3 mm height of bluffbodies, 6.8 mm pitch of bluffbodies has a best performance in all 10 prototypes, which implements a maximum flow rate of 87.5 ml/min at 170 V 40 Hz with a noise of 42.6 dB. This study makes a preliminary investigation and theoretical explanation for the subsequent optimization of this structure, improved the performance of the valveless piezoelectric pump, broaden the thinking of the design for the bluffbody for better performance of the valveless piezoelectric pump.

scholarly journals Experimental Verification of the Pumping Effect Caused by the Micro-Tapered Hole in a Piezoelectric Atomizer

Sensors ◽  
2018 ◽  
Vol 18 (7) ◽  
pp. 2311 ◽  
Author(s):  
Jianhui Zhang ◽  
Qiufeng Yan ◽  
Jun Huang ◽  
Chuanyu Wu
Keyword(s):  
Flow Resistance ◽  
Experimental Results ◽  
Environmental Scanning ◽  
Rate Measurement ◽  
Flow Tube ◽  
Piezoelectric Pump ◽  
Pumping Effect ◽  
Measurement Experiment ◽  
Valveless Piezoelectric Pump ◽  
Tapered Hole

In this study, we examined the use of a dynamic micro-tapered hole as a micro-scale tapered flow tube valveless piezoelectric pump. Firstly, we obtained photographs of a micro-tapered hole by using an environmental scanning electron microscope (ESEM). Then, we explained the pump effect of the micro-tapered hole, and derived the atomization rate equation. Furthermore, we reported an atomization rate measurement experiment that eliminated the atomization caused by a pressure increase, and demonstrated that a change in the volume of a micro-tapered hole could produce atomization. The experimental results indicate that, under the same voltage, the forward atomization rate is much higher than the reverse atomization rate and that the atomization rate increases with the micro-tapered hole volume. The experimental results show that the atomization of the micro-tapered aperture atomizer is caused by its pumping effect. Moreover, the flow resistance and volume of the micro-tapered hole can affect the atomization rate.

scholarly journals A large opening and high flow rate  piezoelectric pump with straight arm wheeled check valve

2020 ◽  
Author(s):  
Lipeng He ◽  
Xiaoqiang Wu ◽  
Zhe Wang ◽  
Da Zhao ◽  
Jianming Wen ◽  
...  
Keyword(s):  
Flow Rate ◽  
Cooling System ◽  
Check Valve ◽  
Maximum Flow ◽  
Low Flow ◽  
Piezoelectric Pump ◽  
Cooling Systems ◽  
Microelectronic Devices ◽  
Valve Opening ◽  
Large Opening

Abstract Piezoelectric pumps are applied in cooling systems of microelectronic devices because of their small size. However, cooling efficiency is limited by low flow rate. A Straight arm wheeled check valve made of silica gel was proposed, which can improve flow rate of piezoelectric pump, solve the influence of glue aging on the sealing ability of a wheeled check valve and reduce the size of piezoelectric pump. This paper discusses the influence of valve arm number (N=2, 3 and 4), valve arm width (W=1.0, 1.2 and 1.4mm) and valve thickness (T=0.6, 0.8 and 1.0mm) on flow rate characteristics of piezoelectric pumps. When valve opening rises, the flow rate increases. The simulation results show that valves with 2 valve arms, 0.6mm valve thickness and 1.0mm valve arm width have maximum valve opening. Experimental results show that piezoelectric pumps with different valve parameters have different optimal frequencies. In addition, maximum flow rate is 431.6mL/min at 220V and 70Hz. This paper provides a reference for the application of piezoelectric pump in cooling system.

scholarly journals Research on Inlet and Outlet Structure Optimization to Improve the Performance of Piezoelectric Pump

Micromachines ◽  
2020 ◽  
Vol 11 (8) ◽  
pp. 735 ◽  
Author(s):  
Xiaolong Zhao ◽  
Dingxuan Zhao ◽  
Jiantao Wang ◽  
Tao Li
Keyword(s):  
Flow Rate ◽  
Dynamic Load ◽  
Maximum Flow ◽  
Fluid Simulation ◽  
Maximum Output ◽  
Piezoelectric Pump ◽  
Pump System ◽  
Output Performance ◽  
Pump Inlet ◽  
Application Requirements

As piezoelectric pumps are used in more fields, they are gradually failing to meet the application requirements due to their low output performance. Therefore, improving the output performance of piezoelectric pumps helps to expand their applications. This paper argued that the dynamic load of liquid in the inlet and outlet pipelines was an important factor that weakened the performance of piezoelectric pumps. Therefore, in order to reduce the dynamic load, it was proposed to replace the conventional piezoelectric pump inlet and outlet by an elastic inlet and outlet. After introducing the structure and working principle of elastic inlet and outlet, the mechanism of reducing the dynamic load by elastic inlet and outlet was analyzed. Then, the influence of the elastic cavity height on the performance of the piezoelectric pump was studied from both fluid simulation and theoretical analysis. Finally, several prototypes were made. The effectiveness of the elastic inlet and outlet on improving the performance of the prototype and the effect of the elastic cavity height on the performance of the prototype were tested, respectively. The test results showed that the elastic inlet and outlet effectively improved the flow rate and output backpressure without increasing the maximum output backpressure. The maximum flow rate of the pump system without load was increased by 36%. In addition, the elastic cavity height adversely affected the flow rate and output backpressure of the prototypes, but had no effect on the maximum output backpressure. In summary, the elastic inlet and outlet can effectively increase the output performance of the piezoelectric pump, but the design height should be appropriately reduced.

scholarly journals Numerical simulation and experimental study on valveless piezoelectric pump with triangular obstacles

2021 ◽  
Vol 2083 (2) ◽  
pp. 022028
Author(s):  
Yeming Sun ◽  
Yu Wang ◽  
Yiwei Wang
Keyword(s):  
Numerical Simulation ◽  
Flow Rate ◽  
Flow Resistance ◽  
Reverse Flow ◽  
Maximum Output ◽  
Driving Voltage ◽  
Driving Frequency ◽  
Piezoelectric Pump ◽  
Valveless Pump ◽  
Valveless Piezoelectric Pump

Abstract A valve less piezoelectric pump with triangular obstacles is designed and manufactured, which uses piezoelectric vibrator as power source. The working principle and theoretical flow rate of the valveless piezoelectric pump are analyzed, and its flow rate expression is derived. The flow resistance characteristics of triangular obstacles are simulated by numerical simulation. Based on the mass fraction distribution of liquid water, the forward and reverse flow resistance of triangular obstacles and the influence of triangular obstacles on pumping capacity are analyzed. Finally, two groups of test prototypes of the valveless pump are made by using the engraving machine, and the flow measurement test is carried out. The experimental results show that the valveless piezoelectric pump with triangular obstacles can realize the valveless pumping function, and the pumping flow per unit time increases with the increase of triangular obstacles in the channel, and decreases with the increase of the distance between triangular obstacles and the channel. When the driving voltage is 140V and the driving frequency is 10Hz, the maximum output flow of the piezoelectric pump is 16.26ml/min.

Outcome of Buccal Mucosal Graft Urethroplasty in Long Segment Anterior Urethral Stricture

2020 ◽  
Vol 19 (2) ◽  
pp. 64-68
Author(s):  
Mrinmoy Biswas ◽  
Sudip Das Gupta ◽  
Mohammed Mizanur Rahman ◽  
Sharif Mohammad Wasimuddin
Keyword(s):  
Urethral Stricture ◽  
Flow Rate ◽  
Surgical Outcome ◽  
Simple Technique ◽  
Anterior Segment ◽  
Maximum Flow ◽  
Anastomotic Site ◽  
Buccal Mucosal Graft ◽  
Male Patients

Objective: To assess the success of BMG urethroplasty in long segment anterior urethral stricture. Method: From January 2014 to December 2015, twenty male patients with long anterior segment urethral stricture were managed by BMG urethroplasty. After voiding trial they were followed up at 3 month with Uroflowmetry, RGU & MCU and PVR measurement by USG. Patients were further followed up with Uroflowmetry and PVR at 6 months interval.Successful outcome was defined as normal voiding with a maximum flow rate >15ml /sec and PVR<50 ml with consideration of maximum one attempt of OIU after catheter removal. Results: Mean stricture length was 5.2 cm (range 3-9 cm) and mean follow-up was 15.55 months (range 6-23 months). Only two patients developed stricture at proximal anastomotic site during follow-up. One of them voided normally after single attempt of OIU. Other one required second attempt of OIU and was considered as failure (5%). Conclusion: BMG urethroplasty is a simple technique with good surgical outcome. Bangladesh Journal of Urology, Vol. 19, No. 2, July 2016 p.64-68

scholarly journals Research on a Piezoelectric Pump with Flexible Valves

2021 ◽  
Vol 11 (7) ◽  
pp. 2909
Author(s):  
Weiqing Huang ◽  
Liyi Lai ◽  
Zhenlin Chen ◽  
Xiaosheng Chen ◽  
Zhi Huang ◽  
...  
Keyword(s):  
Flow Rate ◽  
Fluid Transport ◽  
Smooth Transition ◽  
Driving Voltage ◽  
Piezoelectric Pump ◽  
Venous Valve ◽  
Output Pressure ◽  
Small Flow ◽  
Working Principle ◽  
Opening And Closing

Imitating the structure of the venous valve and its characteristics of passive opening and closing with changes in heart pressure, a piezoelectric pump with flexible valves (PPFV) was designed. Firstly, the structure and the working principle of the PPFV were introduced. Then, the flexible valve, the main functional component of the pump, was analyzed theoretically. Finally, an experimental prototype was manufactured and its performance was tested. The research proves that the PPFV can achieve a smooth transition between valved and valveless by only changing the driving signal of the piezoelectric (PZT) vibrator. The results demonstrate that when the driving voltage is 100 V and the frequency is 25 Hz, the experimental flow rate of the PPFV is about 119.61 mL/min, and the output pressure is about 6.16 kPa. This kind of pump can realize the reciprocal conversion of a large flow rate, high output pressure, and a small flow rate, low output pressure under the electronic control signal. Therefore, it can be utilized for fluid transport and pressure transmission at both the macro-level and the micro-level, which belongs to the macro–micro combined component.

Research on an axial-mounted dual magnetostrictive material rods-based electro-hydrostatic actuator

2021 ◽  
pp. 1045389X2110145
Author(s):  
Yuchuan Zhu ◽  
Chang Liu ◽  
Yunze Song ◽  
Long Chen ◽  
Yulei Jiang ◽  
...  
Keyword(s):  
Mathematical Model ◽  
Flow Rate ◽  
Flow Distribution ◽  
Maximum Flow ◽  
Magnetostrictive Material ◽  
Simulation Techniques ◽  
Motion State ◽  
New Type ◽  
Output Characteristics ◽  
Active Rectification

In this paper, an electro-hydrostatic actuator driven by dual axial-mounted magnetostrictive material rods-based pumps (MMPs) with a new type of active rectification valve is designed in the current study. Based on flow distribution of the active rectification valve and driving energy provided by two MMPs, the actuator can output continuous and bidirectional displacement. By establishing a mathematical model of the actuating system, using simulation techniques, the change rule of hydraulic cylinder’s motion state caused by different driving signals are studied and analyzed. Test equipment platform is constructed in the laboratory to test the output characteristics and confirm the feasibility of the new concept. The experimental results indicate that the maximum flow rate can reach approximately 2.7 L·min−1, while the operating frequency is 180 Hz.

scholarly journals Effect of Subglottic Stenosis on Vocal Fold Vibration and Voice Production Using Fluid–Structure–Acoustics Interaction Simulation

2021 ◽  
Vol 11 (3) ◽  
pp. 1221
Author(s):  
Dariush Bodaghi ◽  
Qian Xue ◽  
Xudong Zheng ◽  
Scott Thomson
Keyword(s):  
Flow Rate ◽  
Vocal Fold ◽  
Flow Resistance ◽  
Signal To Noise Ratio ◽  
Area Ratio ◽  
Subglottic Stenosis ◽  
Fluid Structure ◽  
Voice Production ◽  
Vocal Fold Vibration ◽  
Glottal Flow

An in-house 3D fluid–structure–acoustic interaction numerical solver was employed to investigate the effect of subglottic stenosis (SGS) on dynamics of glottal flow, vocal fold vibration and acoustics during voice production. The investigation focused on two SGS properties, including severity defined as the percentage of area reduction and location. The results show that SGS affects voice production only when its severity is beyond a threshold, which is at 75% for the glottal flow rate and acoustics, and at 90% for the vocal fold vibrations. Beyond the threshold, the flow rate, vocal fold vibration amplitude and vocal efficiency decrease rapidly with SGS severity, while the skewness quotient, vibration frequency, signal-to-noise ratio and vocal intensity decrease slightly, and the open quotient increases slightly. Changing the location of SGS shows no effect on the dynamics. Further analysis reveals that the effect of SGS on the dynamics is primarily due to its effect on the flow resistance in the entire airway, which is found to be related to the area ratio of glottis to SGS. Below the SGS severity of 75%, which corresponds to an area ratio of glottis to SGS of 0.1, changing the SGS severity only causes very small changes in the area ratio; therefore, its effect on the flow resistance and dynamics is very small. Beyond the SGS severity of 75%, increasing the SGS severity, leads to rapid increases of the area ratio, resulting in rapid changes in the flow resistance and dynamics.

Sign in / Sign up

Export Citation Format

Share Document