scholarly journals Study of the Hygrothermal Behavior of Wood Fiber Insulation Subjected to Non-Isothermal Loading

2019 ◽  
Vol 9 (11) ◽  
pp. 2359 ◽  
Author(s):  
Zakaria Slimani ◽  
Abdelkrim Trabelsi ◽  
Joseph Virgone ◽  
Roberto Zanetti Freire
Keyword(s):  
Mathematical Model ◽  
Water Vapor ◽  
Wood Fiber ◽  
Water Vapor Adsorption ◽  
Vapor Concentration ◽  
Transfer Model ◽  
Experimental Setup ◽  
State Variables ◽  
Strongly Coupled ◽  
Latent Effects

Building envelopes are constantly subjected to temperature and moisture gradients. This loading induces a complex response, particularly for highly hygroscopic insulating materials. Latent effects can no longer be neglected for these materials in which heat and moisture transfers are strongly coupled. The purpose of this article is to analyze the behavior of a wood fiber insulation subjected to non-isothermal loading under a vapor concentration gradient. An experimental setup and a mathematical model of hygrothermal transfer were developed to analyze the behavior of the wall. The mathematical model describes the main physical phenomena involved, notably water vapor adsorption and the dependence of thermophysical properties in state variables. The experimental setup developed allows studying a wall under controlled conditions. The temperature and relative humidity profiles within the wall were measured. The evolution of the profiles with time suggests that the adsorption of the water vapor occurs together with the redistribution of liquid water within the envelope. The comparison of the experimental results with the numerical model shows good agreement although the prediction can be improved during the transient phase. The comparisons of these results with a purely diffusive thermal transfer model show the limits of the latter and permit quantifying the latent effects on the total heat transfer.

scholarly journals Numerical Simulation of the Water Vapor Separation of a Moisture-Selective Hollow-Fiber Membrane for the Application in Wood Drying Processes

Membranes ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 593
Author(s):  
Nasim Alikhani ◽  
Douglas W. Bousfield ◽  
Jinwu Wang ◽  
Ling Li ◽  
Mehdi Tajvidi
Keyword(s):  
Water Vapor ◽  
Constant Temperature ◽  
Hollow Fiber ◽  
Hollow Fiber Membrane ◽  
Vacuum Pressure ◽  
Vapor Concentration ◽  
Water Vapor Concentration ◽  
Fiber Membrane ◽  
Wood Drying ◽  
Air Velocity

In this study, a simplified two-dimensional axisymmetric finite element analysis (FEA) model was developed, using COMSOL Multiphysics® software, to simulate the water vapor separation in a moisture-selective hollow-fiber membrane for the application of air dehumidification in wood drying processes. The membrane material was dense polydimethylsiloxane (PDMS). A single hollow fiber membrane was modelled. The mass and momentum transfer equations were simultaneously solved to compute the water vapor concentration profile in the single hollow fiber membrane. A water vapor removal experiment was conducted by using a lab-scale PDMS hollow fiber membrane module operated at constant temperature of 35 °C. Three operation parameters of air flow rate, vacuum pressure, and initial relative humidity (RH) were set at different levels. The final RH of dehydrated air was collected and converted to water vapor concentration to validate simulated results. The simulated results were fairly consistent with the experimental data. Both experimental and simulated results revealed that the water vapor removal efficiency of the membrane system was affected by air velocity and vacuum pressure. A high water vapor removal performance was achieved at a slow air velocity and high vacuum pressure. Subsequently, the correlation of Sherwood (Sh)–Reynolds (Re)–Schmidt (Sc) numbers of the PDMS membrane was established using the validated model, which is applicable at a constant temperature of 35 °C and vacuum pressure of 77.9 kPa. This study delivers an insight into the mass transport in the moisture-selective dense PDMS hollow fiber membrane-based air dehumidification process, with the aims of providing a useful reference to the scale-up design, process optimization and module development using hollow fiber membrane materials.

Modal Analysis of the Axial Compressor Blade: Advanced Time-Dependent Electronic Interferometry and Finite Element Method

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Mykhaylo Tkach ◽  
Serhii Morhun ◽  
Yuri Zolotoy ◽  
Irina Zhuk
Keyword(s):  
Experimental Data ◽  
Mathematical Model ◽  
Finite Element ◽  
High Reliability ◽  
Axial Compressor ◽  
Time Dependent ◽  
Experimental Setup ◽  
Vibration Modes ◽  
Compressor Blades ◽  
Isoparametric Finite Element

AbstractNatural frequencies and vibration modes of axial compressor blades are investigated. A refined mathematical model based on the usage of an eight-nodal curvilinear isoparametric finite element was applied. The verification of the model is carried out by finding the frequencies and vibration modes of a smooth cylindrical shell and comparing them with experimental data. A high-precision experimental setup based on an advanced method of time-dependent electronic interferometry was developed for this aim. Thus, the objective of the study is to verify the adequacy of the refined mathematical model by means of the advanced time-dependent electronic interferometry experimental method. The divergence of the results of frequency measurements between numerical calculations and experimental data does not exceed 5 % that indicates the adequacy and high reliability of the developed mathematical model. The developed mathematical model and experimental setup can be used later in the study of blades with more complex geometric and strength characteristics or in cases when the real boundary conditions or mechanical characteristics of material are uncertain.

Water vapor adsorption on metal-exchanged hierarchical porous zeolite-Y

2021 ◽  
pp. 111380
Author(s):  
Aasif A. Dabbawala ◽  
K. Suresh kumar Reddy ◽  
Hemant Mittal ◽  
Yasser Al Wahedi ◽  
Balasubramanian V. Vaithilingam ◽  
...  
Keyword(s):  
Water Vapor ◽  
Zeolite Y ◽  
Water Vapor Adsorption ◽  
Vapor Adsorption ◽  
Hierarchical Porous

scholarly journals A Satellite-Based Assessment of Upper-Tropospheric Water Vapor Measurements during AFWEX

2009 ◽  
Vol 48 (11) ◽  
pp. 2284-2294 ◽  
Author(s):  
Eui-Seok Chung ◽  
Brian J. Soden
Keyword(s):  
Water Vapor ◽  
Radiative Transfer Model ◽  
Transfer Model ◽  
Raman Lidar ◽  
Test Bed ◽  
Upper Troposphere ◽  
Brightness Temperatures ◽  
Radiation Test ◽  
Humidity Measurements ◽  
Atmospheric Radiation Measurement

Abstract Consistency of upper-tropospheric water vapor measurements from a variety of state-of-the-art instruments was assessed using collocated Geostationary Operational Environmental Satellite-8 (GOES-8) 6.7-μm brightness temperatures as a common benchmark during the Atmospheric Radiation Measurement Program (ARM) First International Satellite Cloud Climatology Project (ISCCP) Regional Experiment (FIRE) Water Vapor Experiment (AFWEX). To avoid uncertainties associated with the inversion of satellite-measured radiances into water vapor quantity, profiles of temperature and humidity observed from in situ, ground-based, and airborne instruments are inserted into a radiative transfer model to simulate the brightness temperature that the GOES-8 would have observed under those conditions (i.e., profile-to-radiance approach). Comparisons showed that Vaisala RS80-H radiosondes and Meteolabor Snow White chilled-mirror dewpoint hygrometers are systemically drier in the upper troposphere by ∼30%–40% relative to the GOES-8 measured upper-tropospheric humidity (UTH). By contrast, two ground-based Raman lidars (Cloud and Radiation Test Bed Raman lidar and scanning Raman lidar) and one airborne differential absorption lidar agree to within 10% of the GOES-8 measured UTH. These results indicate that upper-tropospheric water vapor can be monitored by these lidars and well-calibrated, stable geostationary satellites with an uncertainty of less than 10%, and that correction procedures are required to rectify the inherent deficiencies of humidity measurements in the upper troposphere from these radiosondes.

Bi-wetting property of oil sands fine solids determined by film flotation and water vapor adsorption

Fuel ◽  
2017 ◽  
Vol 197 ◽  
pp. 326-333 ◽  
Author(s):  
Cheng Wang ◽  
Qi Liu ◽  
Douglas G. Ivey ◽  
Thomas H. Etsell
Keyword(s):  
Water Vapor ◽  
Oil Sands ◽  
Water Vapor Adsorption ◽  
Vapor Adsorption ◽  
Wetting Property

Production of Activated Carbon for Water Vapor Adsorption by KOH and NaOH Activation

2006 ◽  
Vol 32 (2) ◽  
pp. 186-189 ◽  
Author(s):  
Jun Kobayashi ◽  
Takahiro Imamura ◽  
Masaaki Ichikawa ◽  
Mitsuhiro Kubota ◽  
Fujio Watanabe ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Water Vapor ◽  
Water Vapor Adsorption ◽  
Vapor Adsorption

Degradation of Solid Oxide Fuel Cell Cathodes Accelerated at a High Water Vapor Concentration

2010 ◽  
Vol 7 (2) ◽  
Author(s):  
S. H. Kim ◽  
K. B. Shim ◽  
C. S. Kim ◽  
J. T. Chou ◽  
T. Oshima ◽  
...  
Keyword(s):  
Water Vapor ◽  
Voltage Drop ◽  
Cell Voltage ◽  
High Water ◽  
Solid Oxide ◽  
Constant Current ◽  
Vapor Concentration ◽  
Water Vapor Concentration ◽  
Oxide Fuel ◽  
Constant Current Density

The influence of water vapor in air on power generation characteristic of solid oxide fuel cells was analyzed by measuring cell voltage at a constant current density, as a function of water vapor concentration at 800°C and 1000°C. Cell voltage change was negligible at 1000°C, while considerable voltage drop was observed at 800°C accelerated at high water vapor concentrations of 20 wt % and 40 wt %. It is considered that La2O3 formed on the (La0.8Sr0.2)0.98MnO3 surface, which is assumed to be the reason for a large voltage drop.

Sign in / Sign up

Export Citation Format

Share Document