scholarly journals Mechanical Behaviour of TRC Composites: Experimental and Analytical Approaches

2019 ◽  
Vol 9 (7) ◽  
pp. 1492 ◽  
Author(s):  
Marco Carlo Rampini ◽  
Giulio Zani ◽  
Matteo Colombo ◽  
Marco di Prisco
Keyword(s):  
Reinforced Concrete ◽  
Mechanical Behaviour ◽  
High Performance ◽  
Tensile Tests ◽  
Seismic Retrofitting ◽  
Analytical Models ◽  
Uniaxial Tensile ◽  
Textile Reinforced Concrete ◽  
Predictive Approaches ◽  
Analytical Approaches

Textile reinforced concrete (TRC) is a promising high-performance material that has been employed with success in new constructions, as well as a strengthening layer of existing structural components. In this work, we document the optimisation procedure of textile-based composites for new construction and for the seismic retrofitting of under-reinforced concrete elements and masonry buildings. The study, aimed at maximising the material performances avoiding waste of economic resources, was addressed by means of a series of uniaxial tensile tests conducted on a wide set of alkali-resistant (AR) glass fabrics and TRCs. The samples differed in terms of cement-based matrices, embedded textiles and addition of dispersed microfibers. The results highlight the effects of fabric characteristics and introduction of short fibres on the mechanical behaviour, proposing novel comparison parameters based upon the load bearing capacity and the deformation response of the composites. The application of simplified analytical models borrowed from the literature finally revealed the limitations of the available predictive approaches, suggesting future lines of investigation.

scholarly journals Influence of the surface modification by sanding of carbon textile reinforcements on the bond and load-bearing behavior of textile reinforced concrete

2019 ◽  
Vol 289 ◽  
pp. 04006
Author(s):  
Cynthia Morales Cruz ◽  
Michael Raupach
Keyword(s):  
Surface Modification ◽  
Reinforced Concrete ◽  
Tensile Tests ◽  
Measuring System ◽  
Uniaxial Tensile ◽  
Testing Time ◽  
Textile Reinforced Concrete ◽  
Load Bearing ◽  
Surface Modified ◽  
Bearing Behavior

In the context of the application of carbon Textile Reinforced Concrete (TRC) layers for the durable repair of building surfaces, uniaxial tensile tests on rectangular TRC samples were carried out to compare the bond and load-bearing behavior of an epoxy-impregnated carbon textile and its surface modified version. The aim of the surface modification, consisting of a subsequent coating with epoxy resin and sanding with quartz sand, is the improvement of the composite material regarding crack width reduction and an increase of the load-bearing capacity. A total of 15 series were examined and the parameters: reinforcement type, orientation and ratio were varied. In addition, long-term load tests were conducted. An optical 3D-video measuring system in combination with a DIC-software was used, which allowed the analysis of the process of crack formation during the entire testing time. With the surface modified reinforcement the formation of approx. 1.5 times the number of cracks with averagely 33 % smaller crack widths and up to 50 % smaller crack spacings were observed, regardless of the ratio of reinforcement. The residual behaviour of the series subjected to a permanent load of 1500 MPa over 1000 h showed no reduction of the tensile stress compared to short-term tests.

Mechanical in-plane behaviour of masonry walls reinforced by composite materials: Experimental and analytical approaches

2017 ◽  
Vol 51 (30) ◽  
pp. 4231-4249 ◽  
Author(s):  
L Bui ◽  
N Reboul ◽  
A Si Larbi ◽  
E Ferrier
Keyword(s):  
Reinforced Concrete ◽  
Composite Materials ◽  
Experimental Tests ◽  
Analytical Models ◽  
Masonry Walls ◽  
Masonry Structures ◽  
Textile Reinforced Concrete ◽  
Reinforced Polymers ◽  
Externally Bonded ◽  
Analytical Approaches

Masonry is a traditional building system in most countries of the world, including France. However, in recent decades, earthquakes have caused significant damage to masonry structures. The possibility of using textile-reinforced concrete or fibre-reinforced polymers to strengthen masonry structures has been recently assessed. This article addresses the effectiveness of externally bonded composite materials, particularly those based on newly developed cementitious matrices, to strengthen masonry structures. Experimental tests were performed in a previous study on six masonry walls, five of which were strengthened on both sides with either textile-reinforced concrete or fibre-reinforced polymers. This experimental campaign has been supplemented to determine the mechanical properties of the materials involved in design models, and it is used to check the potential of analytical models to predict lateral strength. This study identifies the interests and the restrictions governing the use of traditional empirical design approaches (employed for fibre-reinforced polymer-strengthened walls) when next-generation textile-reinforced concrete composites are used as strengthening materials. Adjustments taking into account the specificities of textile-reinforced concrete behaviour have been introduced, and their impact on the relevance of the models has been quantified.

scholarly journals Behaviour of UHPFRCs in compression under high stress-rates

2018 ◽  
Vol 183 ◽  
pp. 02005
Author(s):  
Ezio Cadoni ◽  
Matteo Dotta ◽  
Daniele Forni
Keyword(s):  
Reinforced Concrete ◽  
Mechanical Behaviour ◽  
High Performance ◽  
High Stress ◽  
Slight Reduction ◽  
Fibre Reinforcement ◽  
Fibre Reinforced Concrete ◽  
Dynamic Event ◽  
The Matrix ◽  
High Performance Fibre

The paper presents the results obtained on cylindrical Ultra High Performance Fibre Reinforced Concrete specimens with diameter of 30mm and a height of 60mm under compression at high stress rate (1.7–2.3 TPa/s). Four different percentages of fibre reinforcement are considered (1, 2, 3, and 4% fibre content) and compared with the results of the matrix (UHPC). A slight reduction of the strength and fracture time with the introduction of fibres is observed. The experimental results are analysed and discussed with the intent to better understand the mechanical behaviour of UHPFRC materials in case of dynamic event under service loading conditions.

The tensile behaviour of biaxial and triaxial braided fabrics

2016 ◽  
Vol 47 (8) ◽  
pp. 2184-2204 ◽  
Author(s):  
Duchamp Boris ◽  
Legrand Xavier ◽  
Soulat Damien
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Mechanical Behaviour ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Tensile Behaviour ◽  
Linear Mass ◽  
Double Peak ◽  
Specific Behaviour ◽  
Braiding Angle

The tensile behaviour of braid reinforcement is classically described by the behaviour of composite elaborated from these reinforcements. Few studies concern the tensile behaviour of braided fabrics. In this paper biaxial and triaxial braids are manufactured on a braiding loom. The evolution of key parameters as linear mass and braiding angle in function of process parameters is presented. Braid reinforcements are characterized in uniaxial tensile. The mechanical behaviour is analysed and compared in function of the braiding angle, but also different kinds of braid are considered. A specific behaviour called “double-peak” is identified for triaxial braids which have a higher braiding angle. The evolution of the braiding angle measured during tensile tests gives a comprehension on the mechanical behaviour of dry braids. Associated with this experimental study, an analytical model is also proposed, to predict mechanical properties of braid reinforcements.

scholarly journals Flexural and Shear Tests on Reinforced Concrete Bridge Deck Slab Segments with a Textile-Reinforced Concrete Strengthening Layer

Materials ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 4210 ◽  
Author(s):  
Viviane Adam ◽  
Jan Bielak ◽  
Christian Dommes ◽  
Norbert Will ◽  
Josef Hegger
Keyword(s):  
Reinforced Concrete ◽  
High Performance ◽  
Large Scale ◽  
Shear Failure ◽  
Bridge Deck ◽  
High Strength ◽  
Shear Capacity ◽  
Strengthening Effect ◽  
Textile Reinforced Concrete ◽  
Carbon Fibre Reinforced Polymer

Many older bridges feature capacity deficiencies. This is mainly due to changes in code provisions which came along with stricter design rules and increasing traffic, leading to higher loads on the structure. To address capacity deficiencies of bridges, refined structural analyses with more detailed design approaches can be applied. If bridge assessment does not provide sufficient capacity, strengthening can be a pertinent solution to extend the bridge’s service lifetime. For numerous cases, applying an extra layer of textile-reinforced concrete (TRC) can be a convenient method to achieve the required resistance. Here, carbon fibre-reinforced polymer reinforcement together with a high-performance mortar was used within the scope of developing a strengthening layer for bridge deck slabs, called SMART-DECK. Due to the high tensile strength of the carbon and its resistance to corrosion, a thin layer with high strength and low additional dead load can be realised. While the strengthening effect of TRC for slabs under flexural loading has already been investigated several times, the presented test programme also covered increase in shear capacity, which is the other crucial failure mode to be considered in design. A total of 14 large-scale tests on TRC-strengthened slab segments were tested under static and cyclic loading. The experimental study revealed high increases in capacity for both bending and shear failure.

scholarly journals Anisotropic mechanical behaviour of calendered nonwoven fabrics: Strain-rate dependency

2020 ◽  
pp. 002199832097679
Author(s):  
V Cucumazzo ◽  
E Demirci ◽  
B Pourdeyhimi ◽  
VV Silberschmidt
Keyword(s):  
Strain Rate ◽  
Mechanical Behaviour ◽  
Mechanical Response ◽  
Tensile Tests ◽  
Elastic Response ◽  
Uniaxial Tensile ◽  
Rate Dependency ◽  
Fibrous Matrix ◽  
Nonwoven Fabrics ◽  
Linear Elastic

Calendered nonwovens, formed by polymeric fibres, are three-phase heterogeneous materials, comprising a fibrous matrix, bond-areas and interface regions. As a result, two main factors of anisotropy can be identified. The first one is ascribable to a random fibrous microstructure, with the second one related to orientation of a bond pattern. This paper focuses on the first type of anisotropy in thin and thick nonwovens under uniaxial tensile loading. Individual and combined effects of anisotropy and strain rate were studied by conducting uniaxial tensile tests in various loading directions (0°, 30°, 45°, 60° and 90° with regard to the main fabric’s direction) and strain rate (0.01, 0.1 and 0.5 s−1). Fabrics exhibited an initial linear elastic response, followed by nonlinear strain hardening up to necking and final softening. The studied allowed assessment of the extent the effects of loading direction (anisotropy), planar density and strain rate on the mechanical response of the calendered fabrics. The evidence supported the conclusion that anisotropy is the most crucial factor, also delineating the balance between the fabric’s load-bearing capacity and extension level along various directions. The strain rate produced a marked effect on the fibre’s response, with increased stress at higher strain rate while this effect in the fabric was small. The results demonstrated the differences of the mechanical behaviour of fabrics from that of their constituent fibres.

Sign in / Sign up

Export Citation Format

Share Document