scholarly journals Anisotropic mechanical behaviour of calendered nonwoven fabrics: Strain-rate dependency

2020 ◽  
pp. 002199832097679
Author(s):  
V Cucumazzo ◽  
E Demirci ◽  
B Pourdeyhimi ◽  
VV Silberschmidt
Keyword(s):  
Strain Rate ◽  
Mechanical Behaviour ◽  
Mechanical Response ◽  
Tensile Tests ◽  
Elastic Response ◽  
Uniaxial Tensile ◽  
Rate Dependency ◽  
Fibrous Matrix ◽  
Nonwoven Fabrics ◽  
Linear Elastic

Calendered nonwovens, formed by polymeric fibres, are three-phase heterogeneous materials, comprising a fibrous matrix, bond-areas and interface regions. As a result, two main factors of anisotropy can be identified. The first one is ascribable to a random fibrous microstructure, with the second one related to orientation of a bond pattern. This paper focuses on the first type of anisotropy in thin and thick nonwovens under uniaxial tensile loading. Individual and combined effects of anisotropy and strain rate were studied by conducting uniaxial tensile tests in various loading directions (0°, 30°, 45°, 60° and 90° with regard to the main fabric’s direction) and strain rate (0.01, 0.1 and 0.5 s−1). Fabrics exhibited an initial linear elastic response, followed by nonlinear strain hardening up to necking and final softening. The studied allowed assessment of the extent the effects of loading direction (anisotropy), planar density and strain rate on the mechanical response of the calendered fabrics. The evidence supported the conclusion that anisotropy is the most crucial factor, also delineating the balance between the fabric’s load-bearing capacity and extension level along various directions. The strain rate produced a marked effect on the fibre’s response, with increased stress at higher strain rate while this effect in the fabric was small. The results demonstrated the differences of the mechanical behaviour of fabrics from that of their constituent fibres.

scholarly journals Experimental investigations of the human oesophagus: anisotropic properties of the muscular layer in large deformation

2021 ◽  
Author(s):  
Ciara Durcan ◽  
Mokarram Hossain ◽  
Gregory Chagnon ◽  
Djordje Peric ◽  
Lara Bsiesy ◽  
...  
Keyword(s):  
Strain Rate ◽  
Ex Vivo ◽  
Longitudinal Direction ◽  
Tensile Tests ◽  
Endoscopic Biopsy ◽  
Circumferential Direction ◽  
Experimental Investigations ◽  
Uniaxial Tensile ◽  
Rate Dependency ◽  
Muscular Layer

Technological advancements in the field of robotics have led to endoscopic biopsy devices able to extract diseased tissue from between the layers of the gastrointestinal tract. Despite this, the layer-dependent properties of these tissues have yet to be mechanically characterised using human tissue. In this study, the ex vivo mechanical properties of the passive muscularis propia layer of the human oesophagus were extensively investigated. For this, a series of uniaxial tensile tests were conducted. The results displayed hyperelastic behaviour, while the differences between loading the tissue in both the longitudinal and circumferential directions showcased its anisotropy. The anisotropy of the muscular layer was present at different strain rates, with the longitudinal direction being consistently stiffer than the circumferential one. The circumferential direction was found to have little strain-rate dependency, while the longitudinal direction results suggest pronounced strain-rate-dependent behaviour. The repeated trials showed larger variation in terms of stress for a given strain in the longitudinal direction compared to the circumferential direction. The possible causes of variation between trials are discussed, and the experimental findings are linked to the histological analysis which was carried out via various staining methods. Finally, the direction-dependent experimental data was simulated using an anisotropic, hyperelastic model.

Analysis of temperature and strain rate dependencies of softening regime for tempered martensitic steel

2017 ◽  
Vol 52 (4) ◽  
pp. 226-238 ◽  
Author(s):  
Johanna Eisenträger ◽  
Konstantin Naumenko ◽  
Holm Altenbach ◽  
Elisabetta Gariboldi
Keyword(s):  
Strain Rate ◽  
Mechanical Behaviour ◽  
Elevated Temperatures ◽  
Martensitic Steel ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Test Results ◽  
Strain Localisation ◽  
Surface Measurements ◽  
Softening Stage

This article aims to analyse the influence of temperature and strain rate on the mechanical behaviour of the high-chromium martensitic steel X20CrMoV12-1. The analysis is based on two series of high-temperature uniaxial tensile tests. In a first series, the tensile tests are conducted until rupture, and temperature as well as strain rate are varied systematically. The corresponding stress–strain curves show an extended softening stage. In order to examine softening, it is crucial to distinguish between microstructural changes and strain localisation due to necking. For this reason, a tensile test at low strain rate is performed several times, while the test is terminated at different strain levels in order to examine the onset of necking. Based on the test results and surface measurements of the deformed specimens, the strain level at which necking starts is determined, and possible interactions between softening and necking are discussed. The tensile tests have been conducted in order to calibrate a mechanical model which supplies reliable predictions on the material behaviour under different loading scenarios at elevated temperatures. For this reason, a framework based on microstructural processes is presented in the second part of the article. The model applies a binary mixture approach in conjunction with an iso-strain concept. Furthermore, backstress and softening variables are introduced to consider hardening and softening effects. This procedure results in a system of three differential equations describing the mechanical behaviour.

scholarly journals Experimental Study on the Mechanical Behavior of EN08 Steel at Different Temperatures and Strain Rates

Metals ◽  
2018 ◽  
Vol 8 (9) ◽  
pp. 736 ◽  
Author(s):  
Farid Abed ◽  
Akrum Abdul-Latif ◽  
Ayatollah Yehia
Keyword(s):  
Strain Rate ◽  
Mechanical Response ◽  
Dynamic Compression ◽  
Damage Model ◽  
Tensile Tests ◽  
Dynamic Strain ◽  
Uniaxial Tensile ◽  
Strain Rates ◽  
Compression Tests ◽  
Sem Images

The objective of this paper is to investigate the mechanical response of EN08 steel at quasi-static and dynamic strain rates. Uniaxial tensile tests under quasi-static regime (from 0.0015 s−1 to 0.15 s−1) are conducted on EN08 steel at a range of temperatures between 298 K and 923 K. Dynamic compression tests are also performed by using a drop hammer and by considering different masses and heights to study the material response at strain rates up to 800 s−1. Through the stress-strain responses of EN08 steel, a strong dependency of the yield stress as well as the ultimate strength on the strain rate and temperature is recognized. Furthermore, the strain hardening is highly affected by the increase of temperature at all levels of strain rate. The microstructure of the steel is also examined at a fracture by using SEM images to quantify the density of microdefects and define the damage evolution by using an energy-based damage model.

Virtual trabecular bone models and their mechanical response

2008 ◽  
Vol 222 (8) ◽  
pp. 1185-1195 ◽  
Author(s):  
F E Donaldson ◽  
P Pankaj ◽  
A H Law ◽  
A H Simpson
Keyword(s):  
Finite Element ◽  
Trabecular Bone ◽  
Mechanical Behaviour ◽  
Mechanical Response ◽  
Elastic Response ◽  
Anatomical Site ◽  
Virtual Samples ◽  
Micro Level ◽  
Architectural Characteristics

The study of the mechanical behaviour of trabecular bone has extensively employed micro-level finite element (μFE) models generated from images of real bone samples. It is now recognized that the key determinants of the mechanical behaviour of bone are related to its micro-architecture. The key indices of micro-architecture, in turn, depend on factors such as age, anatomical site, sex, and degree of osteoporosis. In practice, it is difficult to acquire sufficient samples that encompass these variations. In this preliminary study, a method of generating virtual finite element (FE) samples of trabecular bone is considered. Virtual samples, calibrated to satisfy some of the key micro-architectural characteristics, are generated computationally. The apparent level elastic and post-elastic mechanical behaviour of the generated samples is examined: the elastic mechanical response of these samples is found to compare well with natural trabecular bone studies conducted by previous investigators; the post-elastic response of virtual samples shows that material non-linearities have a much greater effect in comparison with geometrical non-linearity for the bone densities considered. Similar behaviour has been reported by previous studies conducted on real trabecular bone. It is concluded that virtual modelling presents a potentially valuable tool in the study of the mechanical behaviour of trabecular bone and the role of its micro-architecture.

The tensile behaviour of biaxial and triaxial braided fabrics

2016 ◽  
Vol 47 (8) ◽  
pp. 2184-2204 ◽  
Author(s):  
Duchamp Boris ◽  
Legrand Xavier ◽  
Soulat Damien
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Mechanical Behaviour ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Tensile Behaviour ◽  
Linear Mass ◽  
Double Peak ◽  
Specific Behaviour ◽  
Braiding Angle

The tensile behaviour of braid reinforcement is classically described by the behaviour of composite elaborated from these reinforcements. Few studies concern the tensile behaviour of braided fabrics. In this paper biaxial and triaxial braids are manufactured on a braiding loom. The evolution of key parameters as linear mass and braiding angle in function of process parameters is presented. Braid reinforcements are characterized in uniaxial tensile. The mechanical behaviour is analysed and compared in function of the braiding angle, but also different kinds of braid are considered. A specific behaviour called “double-peak” is identified for triaxial braids which have a higher braiding angle. The evolution of the braiding angle measured during tensile tests gives a comprehension on the mechanical behaviour of dry braids. Associated with this experimental study, an analytical model is also proposed, to predict mechanical properties of braid reinforcements.

Experimental and Numerical Investigations on Hot Deformation Behavior and Processing Maps for ASS 304 and ASS 316

2018 ◽  
Vol 37 (9-10) ◽  
pp. 873-888 ◽  
Author(s):  
Nitin Kotkunde ◽  
Hansoge Nitin Krishnamurthy ◽  
Swadesh Kumar Singh ◽  
Gangadhar Jella
Keyword(s):  
Experimental Data ◽  
Strain Rate ◽  
Hot Deformation ◽  
Deformation Behavior ◽  
Constitutive Models ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Processing Maps ◽  
Hot Deformation Behavior ◽  
Statistical Measures

AbstractA thorough understanding of hot deformation behavior plays a vital role in determining process parameters of hot working processes. Firstly, uniaxial tensile tests have been performed in the temperature ranges of 150 °C–600 °C and strain rate ranges of 0.0001–0.01s−1 for analyzing the deformation behavior of ASS 304 and ASS 316. The phenomenological-based constitutive models namely modified Fields–Backofen (m-FB) and Khan–Huang–Liang (KHL) have been developed. The prediction capability of these models has been verified with experimental data using various statistical measures. Analysis of statistical measures revealed KHL model has good agreement with experimental flow stress data. Through the flow stresses behavior, the processing maps are established and analyzed according to the dynamic materials model (DMM). In the processing map, the variation of the efficiency of the power dissipation is plotted as a function of temperature and strain rate. The processing maps results have been validated with experimental data.

scholarly journals Mechanical behaviour and structure of snow under uniaxial tensile stress

1980 ◽  
Vol 26 (94) ◽  
pp. 275-282 ◽  
Author(s):  
Hidek Narita
Keyword(s):  
Tensile Stress ◽  
Strain Rate ◽  
Mechanical Behaviour ◽  
Maximum Strength ◽  
Ductile Deformation ◽  
Uniaxial Tensile ◽  
Strain Rates ◽  
Thin Sections ◽  
Uniaxial Tensile Stress ◽  
Small Cracks

AbstractThe mechanical behaviour of snow was studied at — 10°C under uniaxial tensile stress in a range of cross-head speed 6.8 × 10–8to 3.1 × 10–4ms–1and snow density 240-470 kg m–3.It was found from the resisting force-deformation curves that the snow was deformed in two different ways: namely, brittle and ductile deformation at high and low strain-rates, respectively. The critical strain-rate dividing the two deformation modes was found to depend on the density of snow. In ductile deformation, many small cracks appeared throughout the entire specimen. Their features were observed by making thin sections and they were compared with small cracks formed in natural snow on a mountain slope.The maximum strength of snow was found to depend on strain-rate: at strain-rates above about 10–5s–1, the maximum strength increased with decreasing strain-rate but below 10–5s–1it decreased with decreasing strain-rate.

Superplasticity and Microstructure Evolution of Electrodeposited Nanocrystalline Nickel

2007 ◽  
Vol 551-552 ◽  
pp. 539-544 ◽  
Author(s):  
S. Ding ◽  
Kai Feng Zhang ◽  
Guo Feng Wang
Keyword(s):  
Grain Size ◽  
Strain Rate ◽  
Room Temperature ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Intergranular Cracking ◽  
Mean Grain Size ◽  
Electrodeposited Nickel ◽  
Superplastic Properties

Nanocrystalline pure nickel (nc-Ni) was produced by pulse electrodeposition and its superplastic properties at and above room temperature were investigated. The electrodeposited nickel has a narrow grain size distribution with a mean grain size of 70nm. Uniaxial tensile tests at room temperature showed that nc-Ni has a limited plasticity but high tensile strength up to 1GPa at strain rates between 10-5 and 10-2s-1. However, when the temperature increased to 420 and higher, test specimens showed uniform deformation and the elongation value was larger than 200%. A maximum elongation value of 380% was observed at 450°C and a strain rate of 1.67x10-3s-1, SEM and TEM were used to examine the microstructures of the as-deposited and deformed specimens. The results indicated that fracture was caused by intergranular cracking and most cracks were originated from the brittle oxide formed during the tensile test. Grain coarsening was observed in the deformed specimen. The role of temperature and strain on grain growth was evaluated by comparing the microstructure of deformed samples with that of samples statically annealed. Deformation mechanism was discussed based upon the deformed microstructure and strain rate jump tests.

scholarly journals Mechanical behaviour and structure of snow under uniaxial tensile stress

1980 ◽  
Vol 26 (94) ◽  
pp. 275-282 ◽  
Author(s):  
Hidek Narita
Keyword(s):  
Tensile Stress ◽  
Strain Rate ◽  
Mechanical Behaviour ◽  
Maximum Strength ◽  
Ductile Deformation ◽  
Uniaxial Tensile ◽  
Strain Rates ◽  
Thin Sections ◽  
Uniaxial Tensile Stress ◽  
Small Cracks

AbstractThe mechanical behaviour of snow was studied at — 10°C under uniaxial tensile stress in a range of cross-head speed 6.8 × 10–8 to 3.1 × 10–4 ms–1 and snow density 240-470 kg m–3.It was found from the resisting force-deformation curves that the snow was deformed in two different ways: namely, brittle and ductile deformation at high and low strain-rates, respectively. The critical strain-rate dividing the two deformation modes was found to depend on the density of snow. In ductile deformation, many small cracks appeared throughout the entire specimen. Their features were observed by making thin sections and they were compared with small cracks formed in natural snow on a mountain slope.The maximum strength of snow was found to depend on strain-rate: at strain-rates above about 10–5 s –1, the maximum strength increased with decreasing strain-rate but below 10–5 s–1 it decreased with decreasing strain-rate.

Effect of Strain Rate on the Deformation-Induced Martensite Transformation and Mechanical Behavior of Austenitic Stainless Steels for Cold Stretched Pressure Vessels

2010 ◽  
Author(s):  
Cunjian Miao ◽  
Yaxian Li ◽  
Jinyang Zheng
Keyword(s):  
Stainless Steel ◽  
Strain Rate ◽  
Martensite Transformation ◽  
Magnetic Measurement ◽  
Austenitic Stainless Steels ◽  
Tensile Tests ◽  
Pressure Vessels ◽  
Uniaxial Tensile ◽  
Work Hardening Rate ◽  
Proof Strength

Cold stretching (pressure strenghtening) technique has been widely used in austenitic stainless steel pressure vessels in order to increase the proof strength and lighten the weight of the vessels. Cold stretching technique is performed by applying the strengthening pressure under a specified strain rate. Plastic deformation in the process will lead to martensite transformation and may influence material’s strength and ductility. Cold stretching tests of EN 1.4301 stainless steel are carried out at different quasi-static strain rates of 10−3 and 10−5/s, following the uniaxial tensile tests at the same strain rate of 2.5×10−3/s. The α′-martensite transformation is detected by magnetic measurement, meanwhile the work-hardening rate, the flow stress and the mechanical properties of material are studied and the results are presented.

Sign in / Sign up

Export Citation Format

Share Document