scholarly journals Waste Bricks Applied as Removal Agent of Basic Blue 41 from Aqueous Solutions: Base Treatment and Their Regeneration Efficiency

2019 ◽  
Vol 9 (6) ◽  
pp. 1237 ◽  
Author(s):  
Fethi Kooli ◽  
Yan Liu ◽  
Mostafa Abboudi ◽  
Hicham Oudghiri Hassani ◽  
Souad Rakass ◽  
...  
Keyword(s):  
Ph Value ◽  
Cobalt Nitrate ◽  
Regenerative Process ◽  
Contaminated Water ◽  
Slight Variation ◽  
Oxidative Reaction ◽  
Removal Capacity ◽  
Naoh Solution ◽  
The One ◽  
Maximum Removal

Waste brick materials were applied as removal materials of basic blue 41 (BB-41) from artificially contaminated water. They were characterized by different techniques prior their use. A series of removal tests were carried out at different conditions, such as a dosage effect, pH value, initial concentrations, and chemical treatment. The removal results indicated that the two untreated waste bricks had limited removal capacities of basic blue 41, ranging from 19 to 30 mg/g. However, these values were improved upon treatment with NaOH solution or by increasing the removal temperature. Waste brick collected from the Medina area (Med-WB) exhibited higher removal capacity compared to the one collected from the Jeddah area (Jed-WB), with a maximum removal capacity of 60 mg/g at 60 °C. The pH of the BB-41 solution also played an important factor, as it improved the removal amounts from 25 mg/g to 45 mg/g at initial concentration of 200 mg/L. The regenerative process was studied using oxidative reaction of the removed basic blue 41 with a solution of oxone and cobalt nitrate. The efficiency was maintained after 5 runs for Med-WB, with a slight variation of 25%, while it felt to 50% for Jed-WB material after three runs. These data indicate that the waste brick materials present as potential candidates for the dye removal and their origin has to be identified.

scholarly journals Synthesis of Polyaniline Coating on the Modified Fiber Ball and Application for Cr(VI) Removal

2021 ◽  
Vol 16 (1) ◽  
Author(s):  
Xiao Li Ma ◽  
Guang Tao Fei ◽  
Shao Hui Xu
Keyword(s):  
Waste Water ◽  
Large Scale ◽  
Ph Value ◽  
Low Cost ◽  
Strong Acid ◽  
Removal Capacity ◽  
Secondary Pollution ◽  
Potential Possibility ◽  
Fiber Ball ◽  
Maximum Removal

Abstract In this study, polyaniline (PANI) is prepared by means of chemical oxidization polymerization and directly loaded on the modified fiber ball (m-FB) to obtain macroscale polyaniline/modified fiber ball (PANI/m-FB) composite, and then its removal ability of Cr(VI) is investigated. The effects of different parameters such as contact time, pH value and initial concentration on Cr(VI) removal efficiency are discussed. The experimental results illustrate that the favorable pH value is 5.0 and the maximum removal capacity is measured to be 293.13 mg g−1. Besides, PANI/m-FB composites can be regenerated and reused after being treated with strong acid. The kinetic study indicates that the adsorption procedure is mainly controlled by chemical adsorption. More importantly, the macroscale of composites can avoid secondary pollution efficiently. Benefiting from the low cost, easy preparation in large scale, environmentally friendly, excellent recycling performance as well as high removal ability, PANI/m-FB composites exhibit a potential possibility to remove Cr(VI) from industrial waste water. Graphic Abstract The polyaniline (PANI) was coated on modified fiber ball (m-FB) to remove Cr(VI) in waste water, and this kind of PANI/m-FB composites can avoid secondary pollution efficiently due to its macrostructure. Furthermore, the removal capacity can reach to 291.13 mg/g and can be multiple reused.

scholarly journals Phytoremediation of Arsenic Contaminated Water Using Aquatic, Semi-Aquatic and Submerged Weeds

2021 ◽  
Author(s):  
Dibakar Roy ◽  
Dasari Sreekanth ◽  
Deepak Pawar ◽  
Himanshu Mahawar ◽  
Kamal K. Barman
Keyword(s):  
Membrane Filtration ◽  
Lemna Minor ◽  
Typha Latifolia ◽  
Contaminated Water ◽  
Aquatic Weed ◽  
Tolerance Mechanism ◽  
Removal Capacity ◽  
Weed Flora ◽  
The One ◽  
Co Precipitation

Arsenic (As) is the one the most toxic element present in earth which poses a serious threat to the environment and human health. Arsenic contamination of drinking water in South and Southeast Asia reported one of the most threatening problems that causes serious health hazard of millions of people of India and Bangladesh. Further, use of arsenic contaminated ground water for irrigation purpose causes entry of arsenic in food crops, especially in Rice and other vegetable crops. Currently various chemical technologies utilized for As removal from contaminated water like adsorption and co-precipitation using salts, activated charcoal, ion exchange, membrane filtration etc. are very costly and cannot be used for large scale for drinking and agriculture use. In contrast, phytoremediation utilizes green plats to remove pollutants from contaminated water using various mechanisms such as rhizofiltration, phytoextraction, phytostabilization, phytodegrartion and phytovolatilization. A large numbers of terrestrial and aquatic weed flora have been identified so far having hyper metal, metalloid and organic pollutant removal capacity. Among the terrestrial weed flora Arundo donax, Typha latifolia, Typha angustifolia, Vetivaria zizinoids etc. are the hyper As accumulator. Similarly Eicchornea crassipes (Water hyacinth), Pistia stratiotes (water lettuce), Lemna minor (duck weed), Hyrdilla verticillata, Ceratophyllum demersum, Spirodella polyrhiza, Azola, Wolfia spp., etc. are also capable to extract higher amount of arsenic from contaminated water. These weed flora having As tolerance mechanism in their system and thus remediate As contaminated water vis-à-vis continue their life cycle. In this chapter we will discuss about As extraction potential of various aquatic and semi aquatic weeds from contaminated water, their tolerance mechanism, future scope and their application in future world mitigating As contamination in water resources.

scholarly journals Synthesis of polyaniline coating on the modified fiber ball and application for Cr(VI) removal

2021 ◽  
Author(s):  
Xiao Li ◽  
Guang Tao Fei ◽  
Shao Hui Xu
Keyword(s):  
Large Scale ◽  
Ph Value ◽  
Low Cost ◽  
Strong Acid ◽  
Industrial Waste Water ◽  
Removal Capacity ◽  
Secondary Pollution ◽  
Potential Possibility ◽  
Fiber Ball ◽  
Maximum Removal

Abstract In this study, polyaniline (PANI) is prepared by means of chemical oxidization polymerization and directly loaded on the modified fiber ball (m-FB) to obtain macroscale polyaniline/modified fiber ball (PANI/m-FB) composite, and then its removal ability of Cr(VI) is investigated. The effects of different parameters such as contact time, pH value and initial concentration on Cr(VI) removal efficiency are discussed. The experimental results illustrate that the favourable pH value is 5.0 and the maximum removal capacity is measured to be 293.13 mg·g-1. Besides, PANI/m-FB composites can be regenerated and reused after being treated with strong acid. The kinetic study indicates that the adsorption procedure is mainly controlled by chemical adsorption. More importantly, the macroscale of composites can avoid secondary pollution efficiently. Benefiting from the low cost, easy preparation in large scale, environmentally friendly, excellent recycling performance as well as high removal ability, PANI/m-FB composites exhibit a potential possibility to remove Cr(VI) from industrial waste water.

scholarly journals Eggshell Powder as an Adsorbent for Removal of Fluoride from Aqueous Solution: Equilibrium, Kinetic and Thermodynamic Studies

2012 ◽  
Vol 9 (3) ◽  
pp. 1457-1480 ◽  
Author(s):  
R. Bhaumik ◽  
N. K. Mondal ◽  
B. Das ◽  
P. Roy ◽  
K. C. Pal ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
Low Cost ◽  
Fluoride Removal ◽  
Contaminated Water ◽  
Fluoride Adsorption ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Kinetic And Thermodynamic Studies ◽  
Maximum Removal

A new medium, eggshell powder has been developed for fluoride removal from aqueous solution. Fluoride adsorption was studied in a batch system where adsorption was found to be pH dependent with maximum removal efficiency at 6.0. The experimental data was more satisfactorily fitted with Langmuir isotherm model. The kinetics and the factor controlling adsorption process fully accepted by pseudo-second-order model were also discussed. Eawas found to be 45.98 kJmol-1by using Arrhenius equation, indicating chemisorption nature of fluoride onto eggshell powder. Thermodynamic study showed spontaneous nature and feasibility of the adsorption process with negative enthalpy (∆H0) value also supported the exothermic nature. Batch experiments were performed to study the applicability of the adsorbent by using fluoride contaminated water collected from affected areas. These results indicate that eggshell powder can be used as an effective, low-cost adsorbent to remove fluoride from aqueous solution as well as groundwater.

scholarly journals Comparison of sorption efficiency of natural and MnO2 coated zeolite for copper removal from model solutions

2021 ◽  
Vol 900 (1) ◽  
pp. 012003
Author(s):  
M Balintova ◽  
Z Kovacova ◽  
S Demcak ◽  
Y Chernysh ◽  
N Junakova
Keyword(s):  
Heavy Metals ◽  
Removal Efficiency ◽  
Ph Value ◽  
Batch Experiments ◽  
Modified Zeolite ◽  
Optimum Ph ◽  
Removal Of Heavy Metals ◽  
Initial Ph ◽  
Correlation Factors ◽  
Maximum Removal

Abstract Removal of heavy metals from the environment is important for living beings. The present work investigates the applicability of the natural and MnO2 - coated zeolite as sorbent for the removal of copper from synthetic solutions. Batch experiments were carried out to identify the influence of initial pH and concentration in the process of adsorption. A maximum removal efficiency of Cu(II) was observed in 10 mg/L for natural (95.6%) and modified (96.4%) zeolite, where the values was almost identical, but at concentration of 500 mg/L was the removal efficiency of modified zeolite three times higher. Based on the correlation factors R2, the Langmuir isotherms better describe the decontamination process than Freundlich. The optimum pH value was set at 5.0.

scholarly journals Biosorption of Pb (II) and Zn (II) from aqueous solution by Oceanobacillus profundus isolated from an abandoned mine

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Wilson Mwandira ◽  
Kazunori Nakashima ◽  
Satoru Kawasaki ◽  
Allison Arabelo ◽  
Kawawa Banda ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Ion Concentration ◽  
Contaminated Site ◽  
Lead Ion ◽  
Contaminated Water ◽  
Metal Chelation ◽  
Anthropogenic Contamination ◽  
Initial Concentration ◽  
Growth Ph ◽  
Maximum Removal

AbstractThe present study investigated biosorption of Pb (II) and Zn (II) using a heavy metal tolerant bacterium Oceanobacillus profundus KBZ 3-2 isolated from a contaminated site. The effects of process parameters such as effect on bacterial growth, pH and initial lead ion concentration were studied. The results showed that the maximum removal percentage for Pb (II) was 97% at an initial concentration of 50 mg/L whereas maximum removal percentage for Zn (II) was at 54% at an initial concentration of 2 mg/L obtained at pH 6 and 30 °C. The isolated bacteria were found to sequester both Pb (II) and Zn (II) in the extracellular polymeric substance (EPS). The EPS facilitates ion exchange and metal chelation-complexation by virtue of the existence of ionizable functional groups such as carboxyl, sulfate, and phosphate present in the protein and polysaccharides. Therefore, the use of indigenous bacteria in the remediation of contaminated water is an eco-friendly way of solving anthropogenic contamination.

Biological treatment characteristics of benzene and toluene in a biofilter packed with cylindrical activated carbon

2002 ◽  
Vol 46 (11-12) ◽  
pp. 51-56 ◽  
Author(s):  
G.-W. Li ◽  
H.-Y. Hu ◽  
J.-M. Hao ◽  
H.-Q. Zhang
Keyword(s):  
Carbon Dioxide ◽  
Activated Carbon ◽  
Gas Flow ◽  
Removal Rate ◽  
Carbon Dioxide Concentration ◽  
Organic Load ◽  
Filler Materials ◽  
Removal Capacity ◽  
Bacillus Spore ◽  
Maximum Removal

The biodegradation of toluene and benzene in a biofilter using cylindrical activated carbon as the filler materials was studied. Three gas flow rates, i.e. 0.25, 0.50 and 0.75 m3/h, corresponding to empty bed gas residence of 75, 37.5 and 25 s, respectively, and total organic load lower than 400 g/m3.h were tested. The biofilter proved to be highly efficient in biodegradation of toluene and benzene, and toluene was more easily degraded than benzene. When each inlet load was lower than 150 g/m3.h, removal rate increased with inlet load and reached a maximum, which was 150 and 120 g/m−3.h for toluene and benzene, respectively. For inlet load higher than the maximum removal capacity conditions, the removal rate decreased with inlet load. Carbon dioxide concentration profile through the biofilter revealed that the mass ratios of carbon dioxide produced to the toluene and benzene removed were 2.15 g(CO2)/g(toluene) and 1.67 g(CO2)/g(benzene), which furthermore, confirmed the biodegradation performance in biofilter. The observation of biotic community demonstrated that the microbes consisted of bacillus, spore bacillus and fungi, of which the spore bacillus was dominant.

The Decoloration Property of Modified Reed Absorbent for Alkaline Fuchsin Wastewater

2013 ◽  
Vol 821-822 ◽  
pp. 365-368
Author(s):  
Yu Ying
Keyword(s):  
Adsorption Isotherm ◽  
Ph Value ◽  
Adsorption Time ◽  
Adsorption Condition ◽  
Adsorption Temperature ◽  
Naoh Solution ◽  
Adsorbent Dose

The modified reed absorbent was obtained by the being treated process with NaOH solution. The decoloration property of modified reed for alkaline fuchsin was studied under different conditions. The effects of adsorbent dose, adsorption temperature, adsorption time and pH value on the decoloration property were investigated, and the optimal adsorption condition was gotten,, the discoloration rate was above 95%. The adsorption isotherm was well represented by the Langmuir.

scholarly journals Phenol Removal Capacity of the Common Duckweed (Lemna minor L.) and Six Phenol-Resistant Bacterial Strains From Its Rhizosphere: In Vitro Evaluation at High Phenol Concentrations

Plants ◽  
2020 ◽  
Vol 9 (5) ◽  
pp. 599
Author(s):  
Olga Radulović ◽  
Slaviša Stanković ◽  
Branka Uzelac ◽  
Vojin Tadić ◽  
Milana Trifunović-Momčilov ◽  
...  
Keyword(s):  
Biofilm Formation ◽  
Lemna Minor ◽  
Antibiotic Sensitivity ◽  
Control Group ◽  
Phenol Removal ◽  
Bacterial Strains ◽  
Removal Capacity ◽  
The Common ◽  
The One

The main topic of this study is the bioremediation potential of the common duckweed, Lemna minor L., and selected rhizospheric bacterial strains in removing phenol from aqueous environments at extremely high initial phenol concentrations. To that end, fluorescence microscopy, MIC tests, biofilm formation, the phenol removal test (4-AAP method), the Salkowski essay, and studies of multiplication rates of sterile and inoculated duckweed in MS medium with phenol (200, 500, 750, and 1000 mg L−1) were conducted. Out of seven bacterial strains, six were identified as epiphytes or endophytes that efficiently removed phenol. The phenol removal experiment showed that the bacteria/duckweed system was more efficient during the first 24 h compared to the sterile duckweed control group. At the end of this experiment, almost 90% of the initial phenol concentration was removed by both groups, respectively. The bacteria stimulated the duckweed multiplication even at a high bacterial population density (>105 CFU mL−1) over a prolonged period of time (14 days). All bacterial strains were sensitive to all the applied antibiotics and formed biofilms in vitro. The dual bacteria/duckweed system, especially the one containing strain 43-Hafnia paralvei C32-106/3, Accession No. MF526939, had a number of characteristics that are advantageous in bioremediation, such as high phenol removal efficiency, biofilm formation, safety (antibiotic sensitivity), and stimulation of duckweed multiplication.

scholarly journals Physicochemical and Microstructural Properties of Red Muds under Acidic and Alkaline Conditions

2020 ◽  
Vol 10 (9) ◽  
pp. 2993
Author(s):  
Qingke Nie ◽  
Youdong Li ◽  
Guohui Wang ◽  
Bing Bai
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Red Mud ◽  
Ph Value ◽  
Soil Layer ◽  
Microstructural Properties ◽  
Naoh Solution ◽  
Red Muds ◽  
Hcl Solution

The main purpose of this study was to characterize the mineral and chemical composition of typical red muds in China. Changes in the physicochemical and microstructural properties of red muds collected from the Shanxi and Shandong provinces were investigated after they were immersed in an alkaline NaOH or an acidic HCl solution for 7, 28, and 120 days. The results showed that red mud has a high cation exchange capacity and active physicochemical properties, which can be closely related to its extremely high alkalinity and complex microstructure. The neutralization of red mud with the HCl solution results in the release of Na+ from the red mud particles into the leachate and can effectively decrease the pH value of the filtrate. The neutralization process can result in a significant decrease in the liquid limit, plastic limit and plasticity index, whereas the opposite was observed for the different parameters after the addition of the NaOH solution. In this sense, acid neutralization can significantly improve the cementation property of the red mud. This result will increase the water permeability of the acid-treated soil layer and improve the growth ability of plants. The specific surface area of red mud immersed in the NaOH solution decreased, whereas the specific surface area of red mud immersed in the HCl solution increased. This study contributes to our understanding of red mud properties after the red mud has been subjected to acidic and alkaline treatments, and the results can provide insights into the safe disposal of red mud.

Sign in / Sign up

Export Citation Format

Share Document