scholarly journals Flame Front and Burned Gas Characteristics for Different Split Injection Ratios and Phasing in an Optical GDI Engine

2019 ◽  
Vol 9 (3) ◽  
pp. 449 ◽  
Author(s):  
Santiago Martinez ◽  
Simona Merola ◽  
Adrian Irimescu
Keyword(s):  
Flame Front ◽  
Soot Formation ◽  
Direct Injection ◽  
Combustion Process ◽  
Pollutant Emissions ◽  
Optical Data ◽  
Cylinder Pressure ◽  
Split Injection ◽  
Gdi Engine ◽  
Injection Strategies

Direct-injection in spark-ignition engines has long been recognized as a valid option for improving fuel economy, reducing CO2 emissions and avoiding knock occurrence due to higher flexibility in control strategies. However, problems associated with mixture formation are responsible for soot emissions, one of the most limiting factors of this technology. Therefore, the combustion process and soot formation were investigated with different injection strategies on a gasoline direct injection (GDI) engine. The experimental analysis was realized on an optically accessible single cylinder engine when applying single, double and triple injection strategies. Moreover, the effect of fuel delivery phasing was also scrutinized by changing the start of the injection during late intake- and early compression-strokes. The duration of injection was split in different percentages between two or three pulses, so as to obtain close to stoichiometric operation in all conditions. The engine was operated at fixed rotational speed and spark timing, with wide-open throttle. Optical diagnostics based on cycle resolved digital imaging was applied during the early and late stages of the combustion process. Detailed information on the flame front morphology and soot formation were obtained. The optical data were correlated to in-cylinder pressure traces and exhaust gas emission measurements. The results suggest that the split injection of the fuel has advantages in terms of reduction of soot formation and NOx emissions and a similar combustion performance with respect to the single injection timing. Moreover, an early injection resulted in higher rates of heat release and in-cylinder pressure, together with a reduction of soot formation and flame distortion. The double injection strategy with higher percentage of fuel injected in the first pulse and early second injection pulse showed the best results in terms of combustion evolution and pollutant emissions. For the operative condition studied, a higher time for mixture homogenization and split of fuel injected in the intake stroke shows the best results.

scholarly journals UV-visible digital imaging of split injection in a Gasoline Direct Injection engine

2015 ◽  
Vol 19 (6) ◽  
pp. 1873-1886
Author(s):  
Simona Merola ◽  
Adrian Irimescu ◽  
Cinzia Tornatore ◽  
Stefano Valentini ◽  
Gregor Kruczek ◽  
...  
Keyword(s):  
Digital Imaging ◽  
Direct Injection ◽  
Gasoline Direct Injection ◽  
Pollutant Emissions ◽  
Optical Data ◽  
Injection Timing ◽  
Particulate Emissions ◽  
Split Injection ◽  
Single Cylinder ◽  
Uv Visible

Ever tighter limits on pollutant emissions and the need to improve energy conversion efficiency have made the application of gasoline direct injection (GDI) feasible for a much wider scale of spark ignition engines. Changing the way fuel is delivered to the engine has thus provided increased flexibility but also challenges, such as higher particulate emissions. Therefore, alternative injection control strategies need to be investigated in order to obtain optimum performance and reduced environmental impact. In this study, experiments were carried out on a single-cylinder GDI optical engine fuelled with commercial gasoline in lean-burn conditions. The single-cylinder was equipped with the head of a commercial turbocharged engine with similar geometrical specifications (bore, stroke, compression ratio) and wall guided fuel injection. Optical accessibility was ensured through a conventional elongated hollow Bowditch piston and an optical crown, accommodating a fused-silica window. Experimental tests were performed at fixed engine speed and injection pressure, whereas the injection timing and the number of injections were adjusted to investigate their influence on combustion and emissions. UV-visible digital imaging was applied in order to follow the combustion process, from ignition to the late combustion phase. All the optical data were correlated with thermodynamic analysis and measurements of exhaust emissions. Split injection strategies (i.e. two injections per cycle) with respect to single injection increased combustion efficiency and stability thanks to an improvement of fuel air mixing. As a consequence, significant reduction in soot formation and exhaust emission with acceptable penalty in terms of HC and NOx were measured.

scholarly journals The effects of split direct injection on the operation of a tractor diesel engine fueled by biodiesel B20

2021 ◽  
Vol 286 ◽  
pp. 01006
Author(s):  
Andrei Laurentiu Niculae ◽  
Adnan Kadhim Rashid ◽  
Radu Chiriac
Keyword(s):  
Diesel Engine ◽  
Fuel Economy ◽  
Direct Injection ◽  
Pollutant Emissions ◽  
Combustion Model ◽  
Split Injection ◽  
Optimal Injection ◽  
Current Emission ◽  
Tractor Diesel ◽  
Injection Strategies

The use of biodiesel-diesel blends is a current solution to some important problems, such as the depletion of oil resources, global warming, and the pollutant emissions of smoke, carbon monoxide, and hydrocarbons of diesel engines. However, the use of this alternative fuel is characterized by a reduction in engine effective power and an increase in brake-specific fuel consumption and nitrogen oxide pollutant emissions. Using the AVL MCC zero-dimensional combustion model of the AVL BOOST simulation program, it was evaluated to what extent split injection strategies can improve the performance and fuel economy of a tractor diesel engine fuelled with biodiesel B20 at maximum brake torque condition considering noise and pollutant emissions limitation. Various pilot – main – post split injection strategies have been studied to establish the optimal injection characteristics in terms of performance and fuel economy. Subsequently, they have been adapted in terms of compliance with current emission standards. In this way, it has been emphasized that the split injection solution is a viable way to improve performance, economy, and pollutant emissions of a tractor diesel engine.

Effects of Intake Port Optimization on Soot Emission from Diesel Engine

2014 ◽  
Vol 535 ◽  
pp. 333-339
Author(s):  
Yue Chen ◽  
Lin Lv ◽  
Jie Shen
Keyword(s):  
Standard Deviation ◽  
Soot Formation ◽  
Combustion Engine ◽  
Double Helix ◽  
Direct Injection ◽  
Combustion Process ◽  
Flow Coefficient ◽  
Swirl Ratio ◽  
Characteristic Parameters ◽  
Double Tangent

All future engine developments must consider the primary task of achieving the required emission levels. An important step towards the development of combustion engines is the optimization of the flow in the intake ports. The charging movement in the combustion chamber, which is generated by the intake flow, considerably influences the quality of the combustion engine. In this paper, steady CFD analysis were applied to different structures of double-tangent-port. The swirl ratio can be improved while flow coefficient remains unchanged if port eccentricity is 34.4 mm. By defining three characteristic parameters, the speed non-uniformity index, standard deviation and mixture concentration standard deviation and equivalent ratio range, quantitatively describing the combustion process in cylinder, and then compared with transient CFD three-dimensional contours, we can see that characteristic parameters can be more accurate and comprehensive in analyzing the influence of inlet structure of soot formation. Effects of different intake ports on fuel-air mixing in a turbocharged diesel direct injection engine during intake and compression strokes are analyzed. It turns out that the optimized double-tangent-port has the highest uniformity of velocity, in the meanwhile, air/fuel mixing is relatively uniform. On the other hand, mixed-port and double-helix-port can cause uneven flow field which is bad for combustion, even though the swirl ratio can increase largely. Finally, the simulation results show that soot emissions of the optimized double-tangent-port have significantly lower levels, at 2200 r/min under full load.

scholarly journals Analysis of creation and combustion process of hydrogen-air mixtures by optical method in isochoric chamber

2017 ◽  
Vol 170 (3) ◽  
pp. 121-125
Author(s):  
Marek BRZEŻAŃSKI ◽  
Tadeusz PAPUGA ◽  
Łukasz RODAK
Keyword(s):  
Combustion Chamber ◽  
Flame Front ◽  
Dose Distribution ◽  
Optical Method ◽  
Direct Injection ◽  
Combustion Process ◽  
Variable Composition ◽  
Mixture Formation ◽  
Before And After

The article considers the analysis of combustion process of hydrogen-air mixture of variable composition. Direct injection of hydrogen into the isochoric combustion chamber was applied and the mixture formation took place during the combustion process. The influence of the dose distribution of the fuel supplied before and after ignition on the formation of the flame front and the course of the pressure in the isochoric combustion chamber was discussed. The filming process and registration of pressure in the isochoric chamber during research of combustion process was applied.

scholarly journals LES study on mixing and combustion in a Direct Injection Spark Ignition engine

2018 ◽  
Vol 73 ◽  
pp. 32
Author(s):  
Nicolas Iafrate ◽  
Anthony Robert ◽  
Jean-Baptiste Michel ◽  
Olivier Colin ◽  
Benedicte Cuenot ◽  
...  
Keyword(s):  
Ignition Time ◽  
Direct Injection ◽  
Combustion Process ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Pollutant Emissions ◽  
Spark Ignition Engines ◽  
Eddy Simulation ◽  
Mixture Preparation ◽  
The Impact

Downsized spark ignition engines coupled with a direct injection strategy are more and more attractive for car manufacturers in order to reduce pollutant emissions and increase efficiency. However, the combustion process may be affected by local heterogeneities caused by the interaction between the spray and turbulence. The aim for car manufacturers of such engine strategy is to create, for mid-to-high speeds and mid-up-high loads, a mixture which is as homogeneous as possible. However, although injection occurs during the intake phase, which favors homogeneous mixing, local heterogeneities of the equivalence ratio are still observed at the ignition time. The analysis of the mixture preparation is difficult to perform experimentally because of limited optical accesses. In this context, numerical simulation, and in particular Large Eddy Simulation (LES) are complementary tools for the understanding and analysis of unsteady phenomena. The paper presents the LES study of the impact of direct injection on the mixture preparation and combustion in a spark ignition engine. Numerical simulations are validated by comparing LES results with experimental data previously obtained at IFPEN. Two main analyses are performed. The first one focuses on the fuel mixing and the second one concerns the effect of the liquid phase on the combustion process. To highlight these phenomena, simulations with and without liquid injection are performed and compared.

Visualization of diesel spray and combustion from lateral side of two-dimensional piston cavity in rapid compression and expansion machine

2020 ◽  
pp. 146808742096229
Author(s):  
Chengyuan Fan ◽  
Daoyuan Wang ◽  
Keiya Nishida ◽  
Yoichi Ogata
Keyword(s):  
High Speed ◽  
Combustion Process ◽  
Video Camera ◽  
Lateral Side ◽  
Two Dimensional ◽  
Split Injection ◽  
Compression And Expansion ◽  
Color Video ◽  
Wall Interaction ◽  
Injection Strategies

Effect of spray/wall interaction in a rapid compression and expansion machine on mixture formation, ignition location, and soot generation was investigated. A two-dimensional piston cavity designed as the cross section of a reentrant piston was utilized to observe the spray and combustion process from the lateral side. The experiment was conducted at 120 MPa injection pressure under single and split injection strategies with an ambient gas of 15% O2 concentration. A shadow methodology was applied to investigate the interaction between the fuel spray and the piston cavity. Combined with the natural flame luminosity captured by a high-speed color video camera, the behaviors of the impinging spray and the combustion process were studied. The combustion characteristics of the in-cylinder pressure, heat release and combustion phase were recorded and analyzed simultaneously. The results showed that the split injection strategies effectively softened the heat release trace and promoted the onset of the main combustion. The cool-flame phenomenon was captured by using the high-speed color video camera, and the intense ignition was observed when the pilot spray was controlled to impinge on the lower lip of the piston rim. Moreover, results also showed that further extending the mixing process of the pilot spray is inclined to form a homogeneous mixture which was beneficial for the promotion of low-temperature combustion and the reduction of soot generation. This research provides a detailed investigation on the spray and combustion process and it highlights the significant effect of spray/wall interaction on the subsequent combustion process.

Diesel Engine Combustion Sensing Methodology Based on Vibration Analysis

2014 ◽  
Vol 136 (11) ◽  
Author(s):  
Ponti Fabrizio ◽  
Ravaglioli Vittorio ◽  
Cavina Nicolò ◽  
De Cesare Matteo
Keyword(s):  
Diesel Engine ◽  
Closed Loop ◽  
Combustion Process ◽  
Pressure Sensors ◽  
Thermal Conditions ◽  
Pollutant Emissions ◽  
Accurate Estimation ◽  
Cylinder Pressure ◽  
Combustion Control ◽  
Real Time Analysis

The increasing request for pollutant emissions reduction spawned a great deal of research in the field of combustion control and monitoring. As a matter of fact, newly developed low temperature combustion strategies for diesel engines allow obtaining a significant reduction both in particulate matter and NOx emissions, combining the use of high EGR rates with a proper injection strategy. Unfortunately, due to their nature, these innovative combustion strategies are very sensitive to in-cylinder thermal conditions. Therefore, in order to obtain a stable combustion, a closed-loop combustion control methodology is needed. Many works demonstrate that a closed-loop combustion control strategy can be based on real-time analysis of in-cylinder pressure trace that provides important information about the combustion process, such as start of combustion, center of combustion and torque delivered by each cylinder. Nevertheless, cylinder pressure sensors on-board installation is still uncommon, due to problems related to unsatisfactory measurement long term reliability and cost. This paper presents a newly developed approach that allows extracting information about combustion effectiveness through the analysis of engine vibrations. In particular, the developed methodology can be used to obtain an accurate estimation of the indicated quantities of interest combining the information provided by engine speed fluctuations measurement and by the signals coming from acceleration transducers mounted on the engine. This paper also reports the results obtained applying the whole methodology to a light-duty turbocharged common rail diesel engine.

Effect of Conical Spray and Multi-Hole Spray on Gasoline Engine Mixture Formation and Combustion Performance Based on Different Injection Strategies

2020 ◽  
Vol 143 (6) ◽  
Author(s):  
Shengli Wei ◽  
Zhiqing Yu ◽  
Zhilei Song ◽  
Fan Yang ◽  
Chengcheng Wu
Keyword(s):  
Gasoline Engine ◽  
Direct Injection ◽  
Mixture Distribution ◽  
Gasoline Direct Injection ◽  
Injection Timing ◽  
Mixture Formation ◽  
Injection Strategy ◽  
Gdi Engine ◽  
The Difference ◽  
Injection Strategies

Abstract This article presents a numerical investigation carried out to determine the effects of second and third injection timing on combustion characteristics and mixture formation of a gasoline direct injection (GDI) engine by comparing conical spray against multihole spray. The results showed that at the engine 80% full load of 2000 r/min, the difference in mixture distribution between the two sprays was obvious with double and triple injection strategies. With the second injection timing from 140 deg CA delay to 170 deg CA, the in-cylinder pressure, the in-cylinder temperature, and the heat release rate of the conical spray increased by 20.8%, 9.8%, and 30.7% and that of the multihole spray decreased by 30.7%, 13.6%, and 37.8%. The delay of the injection time reduced the performance of the engine with the multihole spray, and the performance of the multihole spray was obviously in the simulation of the triple injection strategy. However, for the conical spray, the application of the triple injection strategy increased the temperature and the pressure compared with the double injection strategy.

scholarly journals Modeling diesel combustion with tabulated kinetics and different flame structure assumptions based on flamelet approach

2019 ◽  
Vol 21 (1) ◽  
pp. 89-100 ◽  
Author(s):  
Tommaso Lucchini ◽  
Daniel Pontoni ◽  
Gianluca D’Errico ◽  
Bart Somers
Keyword(s):  
Soot Formation ◽  
Flame Structure ◽  
Combustion Process ◽  
Computational Cost ◽  
Pollutant Emissions ◽  
Diesel Combustion ◽  
Flamelet Generated Manifold ◽  
Tabulated Chemistry ◽  
Computational Fluid Dynamics Analysis ◽  
The Impact

Computational fluid dynamics analysis represents a useful approach to design and develop new engine concepts and investigate advanced combustion modes. Large chemical mechanisms are required for a correct description of the combustion process, especially for the prediction of pollutant emissions. Tabulated chemistry models allow to reduce significantly the computational cost, maintaining a good accuracy. In the present work, an investigation of tabulated approaches, based on flamelet assumptions, is carried out to simulate turbulent Diesel combustion in the Spray A framework. The Approximated Diffusion Flamelet is tested under different ambient conditions and compared with Flamelet Generated Manifold, and both models are validated with Engine Combustion Network experimental data. Flame structure, combustion process and soot formation were analyzed in this work. Computed results confirm the impact of the turbulent–chemistry interaction on the ignition event. Therefore, a new look-up table concept Five-Dimensional-Flamelet Generated Manifold, that accounts for an additional dimension (strain rate), has been developed and tested, giving promising results.

Sign in / Sign up

Export Citation Format

Share Document