scholarly journals Performance Study and Efficiency Improvement of Ice Slurry Production by Scraped-Surface Method

2018 ◽  
Vol 9 (1) ◽  
pp. 74 ◽  
Author(s):  
Xi Liu ◽  
Yueling Li ◽  
Kunyu Zhuang ◽  
Ruansong Fu ◽  
Shi Lin ◽  
...  
Keyword(s):  
Sodium Chloride ◽  
Power Consumption ◽  
Flow Rate ◽  
Coefficient Of Performance ◽  
Total Power ◽  
Solution Flow Rate ◽  
Ice Slurry ◽  
Solution Flow ◽  
Surface Method ◽  
Total Power Consumption

In this study, the performance of ice slurry production by scraped-surface method was experimentally investigated. Temperature change characteristics, ice packing fraction (IPF) of ice slurry, power consumption of scraping system and coefficient of performance (COP) were measured by varying the concentration of sodium chloride solution, scraping speed, and solution flow rate. The effect of nanosilica on efficiency of ice slurry production was also studied. The results showed that scraping power consumption accounted for only a small proportion (about 5%) of the total power consumption of the system. An increase in the concentration of sodium chloride caused a decrease in the IPF and a decrease in the COP of the system. With the solution flow rate at 1.3 m3/h and scraping speed at 13 rpm, the maximum COP (2.43) was obtained. Furthermore, the addition of nanosilica had a significant effect on improving the system COP.

Utilization of Waste of Enzymes Biomass as Biosorbent for the Removal of Dyes from Aqueous Solution in Batch and Fluidized Bed Column

2020 ◽  
Vol 71 (1) ◽  
pp. 1-12
Author(s):  
Salman H. Abbas ◽  
Younis M. Younis ◽  
Mohammed K. Hussain ◽  
Firas Hashim Kamar ◽  
Gheorghe Nechifor ◽  
...  
Keyword(s):  
Experimental Data ◽  
Aqueous Solution ◽  
Particle Size ◽  
Adsorption Capacity ◽  
Fluidized Bed ◽  
Flow Rate ◽  
Fungal Biomass ◽  
Solution Flow Rate ◽  
Maximum Adsorption Capacity ◽  
Solution Flow

The biosorption performance of both batch and liquid-solid fluidized bed operations of dead fungal biomass type (Agaricusbisporus ) for removal of methylene blue from aqueous solution was investigated. In batch system, the adsorption capacity and removal efficiency of dead fungal biomass were evaluated. In fluidized bed system, the experiments were conducted to study the effects of important parameters such as particle size (701-1400�m), initial dye concentration(10-100 mg/L), bed depth (5-15 cm) and solution flow rate (5-20 ml/min) on breakthrough curves. In batch method, the experimental data was modeled using several models (Langmuir,Freundlich, Temkin and Dubinin-Radushkviechmodels) to study equilibrium isotherms, the experimental data followed Langmuir model and the results showed that the maximum adsorption capacity obtained was (28.90, 24.15, 21.23 mg/g) at mean particle size (0.786, 0.935, 1.280 mm) respectively. In Fluidized-bed method, the results show that the total ion uptake and the overall capacity will be decreased with increasing flow rate and increased with increasing initial concentrations, bed depth and decreasing particle size.

scholarly journals Efficient Operation Method of Aquifer Thermal Energy Storage System Using Demand Response

Energies ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3129
Author(s):  
Jewon Oh ◽  
Daisuke Sumiyoshi ◽  
Masatoshi Nishioka ◽  
Hyunbae Kim
Keyword(s):  
Energy Storage ◽  
Power Consumption ◽  
Thermal Energy ◽  
Demand Response ◽  
Thermal Energy Storage ◽  
Heat Storage ◽  
Storage System ◽  
Total Power ◽  
Operation Method ◽  
Total Power Consumption

The mass introduction of renewable energy is essential to reduce carbon dioxide emissions. We examined an operation method that combines the surplus energy of photovoltaic power generation using demand response (DR), which recognizes the balance between power supply and demand, with an aquifer heat storage system. In the case that predicts the occurrence of DR and performs DR storage and heat dissipation operation, the result was an operation that can suppress daytime power consumption without increasing total power consumption. Case 1-2, which performs nighttime heat storage operation for about 6 h, has become an operation that suppresses daytime power consumption by more than 60%. Furthermore, the increase in total power consumption was suppressed by combining DR heat storage operation. The long night heat storage operation did not use up the heat storage amount. Therefore, it is recommended to the heat storage operation at night as much as possible before DR occurs. In the target area of this study, the underground temperature was 19.1 °C, the room temperature during cooling was about 25 °C and groundwater could be used as the heat source. The aquifer thermal energy storage (ATES) system in this study uses three wells, and consists of a well that pumps groundwater, a heat storage well that stores heat and a well that used heat and then returns it. Care must be taken using such an operation method depending on the layer configuration.

scholarly journals A Novel Differential Log-Companding Amplifier for Biosignal Sensing

2016 ◽  
Vol 2016 ◽  
pp. 1-7
Author(s):  
Zigang Dong ◽  
Xiaolin Zhou ◽  
Yuanting Zhang
Keyword(s):  
Power Consumption ◽  
Supply Voltage ◽  
Nonlinear Function ◽  
New Method ◽  
Total Power ◽  
Maximum Output ◽  
Output Current ◽  
Current Range ◽  
Symmetrical Configuration ◽  
Total Power Consumption

We proposed a new method for designing the CMOS differential log-companding amplifier which achieves significant improvements in linearity, common-mode rejection ratio (CMRR), and output range. With the new nonlinear function used in the log-companding technology, this proposed amplifier has a very small total harmonic distortion (THD) and simultaneously a wide output current range. Furthermore, a differential structure with conventionally symmetrical configuration has been adopted in this novel method in order to obtain a high CMRR. Because all transistors in this amplifier operate in the weak inversion, the supply voltage and the total power consumption are significantly reduced. The novel log-companding amplifier was designed using a 0.18 μm CMOS technology. Improvements in THD, output current range, noise, and CMRR are verified using simulation data. The proposed amplifier operates from a 0.8 V supply voltage, shows a 6.3 μA maximum output current range, and has a 6 μW power consumption. The THD is less than 0.03%, the CMRR of this circuit is 74 dB, and the input referred current noise density is166.1 fA/Hz. This new method is suitable for biomedical applications such as electrocardiogram (ECG) signal acquisition.

Exergy Analysis of a Novel Cryogenic Concept for the Liquefaction of Natural Gas Integrated Into an Air Separation Process

2016 ◽  
Author(s):  
S. Tesch ◽  
T. Morosuk ◽  
G. Tsatsaronis
Keyword(s):  
Natural Gas ◽  
Power Consumption ◽  
Exergy Analysis ◽  
Primary Energy ◽  
Separation Process ◽  
Air Separation ◽  
Total Power ◽  
Separation Unit ◽  
Total Power Consumption ◽  
Liquefaction Temperature

The increasing demand for primary energy leads to a growing market of natural gas and the associated market for liquefied natural gas (LNG) increases, too. The liquefaction of natural gas is an energy- and cost-intensive process. After exploration, natural gas, is pretreated and cooled to the liquefaction temperature of around −160°C. In this paper, a novel concept for the integration of the liquefaction of natural gas into an air separation process is introduced. The system is evaluated from the energetic and exergetic points of view. Additionally, an advanced exergy analysis is conducted. The analysis of the concepts shows the effect of important parameters regarding the maximum amount of liquefiable of natural gas and the total power consumption. Comparing the different cases, the amount of LNG production could be increased by two thirds, while the power consumption is doubled. The results of the exergy analysis show, that the introduction of the liquefaction of natural gas has a positive effect on the exergetic efficiency of a convetional air separation unit, which increases from 38% to 49%.

scholarly journals ENERGY IMPLEMENTATION OF SOLAR PANELS FOR REFRIGERATOR NEEDS LOAD FISHING RESULTS 80 WATT MAXIMUM CAPACITY 20 KG

2019 ◽  
Vol 4 (1) ◽  
pp. 19-31
Author(s):  
A. YUNUS NASUTION ◽  
ADITYA PRATAMA
Keyword(s):  
Power Consumption ◽  
Solar Panel ◽  
Coefficient Of Performance ◽  
Total Power ◽  
Cooling Load ◽  
Solar Panels ◽  
Average Output ◽  
Average Value ◽  
Battery Capacity ◽  
Compressor Power

The initial problems of fishermen still use their semi-modern catches and still use ice cubes as a cooling medium, due to the lack of innovation in the development of the cooling media caught by fishermen. The implementation of solar panel energy is the beginning for the development of refrigerator power consumption caught by fishermen. The goal is to calculate the cooling load on the refrigerator, calculate the Coefficient of performance (COP) at the refrigerator and the loading factors at the refrigerator, where the average ambient temperature is 34 ℃ and the temperature to be achieved is 0℃, the fisherman results used in the study this is a shrimp with a capacity of 20 kg and the cooling time is 4 hours. Where the total cooling load value is 244.29 Watt, multiplied by 10% safety factor, so the overall cooling load is 268.72 Watts, refrigerant mass flow rate is 0.0012 Kg / s, the evaporator capacity is 261 Watt, compressor power is 15.6 Watt, The coefficient of performance (COP) value was 16.73 while for the refrigerant capacity was 0.074 Tons of refrigerant, the loading factors in the study were used to run a refrigerator with 80 Watt power for 4 hours, so that the total refrigerator load was 320 Wh (Watt hour) , to produce 320 Wh power is used 2 solar panel modules with a capacity of 50 Wp (Watt Peak), and uses a solar change controller (SCC) with a capacity of 10 A. The output power of the solar panel is influenced by the intensity of the sun's light emitted, from the test obtained an average value the average output of solar panels is 90.6 watts, while the total power generated in 11 test points is 536 watts, the type used is polycrystalline, solar panels battery and inverter capacity must be greater than the refrigerator power consumption, in this study used a 12V 35 Ah battery capacity and 500 Watt Inverter

scholarly journals Pellet Softening Process for the Removal of the Groundwater Hardness; Modelling and Experimentation

2019 ◽  
Vol 12 (3) ◽  
pp. 135-143 ◽  
Author(s):  
Fatin Abdul_kareem Ashoor ◽  
Amer D. Zmat ◽  
Muthanna H. AlDahhan
Keyword(s):  
Calcium Carbonate ◽  
Removal Efficiency ◽  
Flow Rate ◽  
Solution Flow Rate ◽  
Pellet Size ◽  
Solution Flow ◽  
Bed Height ◽  
Naoh Solution ◽  
Softening Process ◽  
Calcium And Magnesium Ions

A lab scale pellet reactor (PR) was designed and fabricated to carry out extensive investigations on the removal efficiency of the hardness of groundwater.  The groundwater of 2200 – 2600 mg/L hardness was collected from Abdulla Ibnalhassan wells area located at the west desert of Al-Shinafiyah district (70 km to the southwest of Al-Dewaniyah city, Iraq). Both hydrodynamic parameters of the pellet reactor (porosity and fluidized bed height) and the parameters of calcium carbonate crystallization process (calcium carbonate equilibrium, pellet size, and density) were modeled and compared with the experimental results of the lab scale pellet reactor. The comparison showed that fair agreement between modeled and measured results was observed. The removal efficiency of both calcium and magnesium ions were 62.5-99% and 83-99% respectively. The removal efficiency was found to be strongly dependent on pH and the ratio of NaOH solution flow rate to the groundwater flow rate in the pellet reactor.

scholarly journals Optimization of Power Consumption for the Design of 802.11n MIMO_OFDM System

2018 ◽  
Vol 26 (4) ◽  
pp. 172-184
Author(s):  
Muthna Jasim Fadhil
Keyword(s):  
Power Consumption ◽  
Orthogonal Frequency Division Multiplexing ◽  
High Speed ◽  
Mimo Systems ◽  
Total Power ◽  
Wireless System ◽  
Generator System ◽  
Total Power Consumption ◽  
Consumption Energy ◽  
High Reduction

In modern systems communication, different methods have been improved to change the prior imitative techniques that process communication data with high speed. It is necessary to improve (OFDM) Orthogonal Frequency Division Multiplexing technique because the development in the guideline communication of wireless system which include security data and transmission data reliability. The applications communications of wireless is important to develop in order to optimize the process of communication leads to reduce the level consumption energy of the output level signal. The architecture of VLSI is used to optimize the performance transceiver in 802.11 n OFDM-MIMO systems, this idea concentrate on the design of 6x6 MIMO_OFDM system in software simulink of MATLAB then using generator system for transfer to code of VHDL and applying in FPGA Xilinx Spartan 3 XC3S200 . The modelsim used to get the simulation while Xilinx power estimator is used to calculate power. The results registered total power consumption about 94mW while compared with previous work  was 136mW which means a high reduction of about 30.8% .

Sign in / Sign up

Export Citation Format

Share Document