scholarly journals Methodology for Optical Engine Characterization by Means of the Combination of Experimental and Modeling Techniques

2018 ◽  
Vol 8 (12) ◽  
pp. 2571 ◽  
Author(s):  
José Pastor ◽  
Pablo Olmeda ◽  
Jaime Martín ◽  
Felipe Lewiski
Keyword(s):  
Heat Transfer ◽  
Heat Release ◽  
Thermodynamic Analysis ◽  
Compression Ratio ◽  
Combustion Process ◽  
Pollutant Emissions ◽  
Transfer Model ◽  
Special Importance ◽  
Cylinder Pressure ◽  
Optical Engine

Optical engines allow for the direct visualization of the phenomena taking place in the combustion chamber and the application of optical techniques for combustion analysis, which makes them invaluable tools for the study of advanced combustion modes aimed at reducing pollutant emissions and increasing efficiency. An accurate thermodynamic analysis of the engine performance based on the in-cylinder pressure provides key information regarding the gas properties, the heat release, and the mixing conditions. If, in addition, optical access to the combustion process is provided, a deeper understanding of the phenomena can be derived, allowing the complete assessment of new injection-combustion strategies to be depicted. However, the optical engine is only useful for this purpose if the geometry, heat transfer, and thermodynamic conditions of the optical engine can mimic those of a real engine. Consequently, a reliable thermodynamic analysis of the optical engine itself is mandatory to accurately determine a number of uncertain parameters among which the effective compression ratio and heat transfer coefficient are of special importance. In the case of optical engines, the determination of such uncertainties is especially challenging due to their intrinsic features regarding the large mechanical deformations of the elongated piston caused by the pressure, and the specific thermal characteristics that affect the in-cylinder conditions. In this work, a specific methodology for optical engine characterization based on the combination of experimental measurements and in-cylinder 0D modeling is presented. On one hand, the method takes into account the experimental deformations measured with a high-speed camera in order to determine the effective compression ratio; on the other hand, the 0D thermodynamic analysis is used to calibrate the heat transfer model and to determine the rest of the uncertainties based on the minimization of the heat release rate residual in motored conditions. The method has been demonstrated to be reliable to characterize the optical engine, providing an accurate in-cylinder volume trace with a maximum deformation of 0.5 mm at 80 bar of peak pressure and good experimental vs. simulated in-cylinder pressure fitting.

Analysis of Incylinder Pressure and Temperature Variation in a Four-Stroke S. I. Engine Using Wiebe’s Combustion Model

2014 ◽  
Vol 984-985 ◽  
pp. 957-961
Author(s):  
Vijayashree ◽  
P. Tamil Porai ◽  
N.V. Mahalakshmi ◽  
V. Ganesan
Keyword(s):  
Heat Release ◽  
Combustion Process ◽  
Pressure Variation ◽  
Spark Ignition Engine ◽  
Working Fluid ◽  
Combustion Model ◽  
Cylinder Pressure ◽  
Crank Angle ◽  
Experimental Values ◽  
Release Model

This paper presents the modeling of in-cylinder pressure variation of a four-stroke single cylinder spark ignition engine. It uses instantaneous properties of working fluid, viz., gasoline to calculate heat release rates, needed to quantify combustion development. Cylinder pressure variation with respect to either volume or crank angle gives valuable information about the combustion process. The analysis of the pressure – volume or pressure-theta data of a engine cycle is a classical tool for engine studies. This paper aims at demonstrating the modeling of pressure variation as a function of crank angle as well as volume with the help of MATLAB program developed for this purpose. Towards this end, Woschni heat release model is used for the combustion process. The important parameter, viz., peak pressure for different compression ratios are used in the analysis. Predicted results are compared with experimental values obtained for a typical compression ratio of 8.3.

Combustion and Emission Characteristics of Dual Fuel Engine for Different Parameters

2021 ◽  
Vol 13 (4) ◽  
Author(s):  
Jianjun Zhu ◽  
Peng Li ◽  
Yufeng Xie ◽  
Xin Geng
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Heat Release Rate ◽  
Compression Ratio ◽  
Release Rate ◽  
Emission Characteristics ◽  
Soot Emission ◽  
Cylinder Pressure ◽  
Fuel Delivery ◽  
Soot Emissions

The effects of compression ratio and fuel delivery advance angle on the combustion and emission characteristics of premixed methanol charge induced ignition by Fischer Tropsch diesel engine were investigated using a CY25TQ diesel engine. In the process of reducing the compression ratio from 16.9 to 15.4, the starting point of combustion is fluctuating, the peak of in-cylinder pressure and the maximum pressure increase rate decrease by 44.5% and 37.7% respectively. The peak instantaneous heat release rate increases by 54.4%. HC and CO emissions are on a rising trend. NOx and soot emissions were greatly decreased. The soot emission has the biggest drop of 50%. Reducing the fuel delivery advance angle will make the peak of in-cylinder pressure and the peak of pressure rise rate increase while the peak of heat release rate decreases. The soot emission is negatively correlated with the fuel delivery advance angle. When the fuel delivery advance angle is 16° CA, the soot emissions increased the most by 130%.

scholarly journals Modeling of a Solar Receiver for Superheating Sulfuric Acid

2016 ◽  
Vol 138 (4) ◽  
Author(s):  
Justin L. Lapp ◽  
Alejandro Guerra-Niehoff ◽  
Hans-Peter Streber ◽  
Dennis Thomey ◽  
Martin Roeb ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Sulfuric Acid ◽  
Thermodynamic Analysis ◽  
Transfer Model ◽  
Heat Transfer Medium ◽  
Modeling And Analysis ◽  
Concentrated Solar Energy ◽  
And Performance ◽  
Solar Receiver ◽  
Individual Design

A volumetric solar receiver for superheating evaporated sulfuric acid is developed as part of a 100 kW pilot plant for the hybrid sulfur (HyS) cycle. The receiver, which uses silicon carbide foam as a heat transfer medium, heats evaporated sulfuric acid using concentrated solar energy to temperatures of 1000 °C or greater, which are required for the downstream catalytic reaction to split sulfur trioxide into oxygen and sulfur dioxide. Multiple parallel approaches for modeling and analysis of the receiver are used to design the prototype. Focused numerical modeling and thermodynamic analysis are applied to answer individual design and performance questions. Numerical simulations focused on fluid flow are used to determine the best arrangement of inlets, while thermodynamic analysis is used to evaluate the optimal dimensions and operating parameters. Finally, a numerical fluid mechanics and heat transfer model is used to predict the temperature field within the receiver. Important lessons from the modeling efforts are given, and their impacts on the design of a prototype are discussed.

Effects of Different LPG Fuel Systems on Performances of Variable Compression Ratio Single Cylinder Engine

2002 ◽  
Author(s):  
G. H. Choi ◽  
J. H. Kim ◽  
Christian Homeyer
Keyword(s):  
Liquid Phase ◽  
Heat Release ◽  
Compression Ratio ◽  
Power Output ◽  
Alternative Fuels ◽  
Gasoline Engine ◽  
Cylinder Pressure ◽  
Maximum Heat ◽  
Spark Timing ◽  
Test Engine

Since the early 20th century, most ground vehicles are driven with gasoline and diesel. The degradation of the environment affects human on earth unless the quality of the air is improved. One of the alternative fuels, LPG, is potentially capable of lowering vehicular emissions when compared to gasoline or diesel. There is a penalty in power output resulting from the use of LPG because the engine can induce less amount of air with Mixer system comparing with gasoline engine. Currently, the liquid-phase LPG is injected into the intake port of the engine, the fuel vaporizes enroute to the combustion chamber. Therefore, the performance and combustion processes of the tested engine are investigated with different LPG fuel systems. The test engine was developed and named heavy-duty VACRE. The test engine for this work operates 1400rpm with MBT conditions. The major conclusions of the work include; 1) The power output of LPi system with liquid-phase is approximately 17% higher than that of vapor-phase Mixer system due to increases of volumetric efficiency. And the MBT spark timing of LPi system is approximately 25% more advanced than that of Mixer system at λ value 1.0; 2) The LPi system shows both the maximum heat release rate and the cumulative heat release to be approximately 20% higher than the Mixer system; 3) Maximum cylinder pressure decrease with increase of compression ratio and a point of maximum cylinder pressure is delayed with high compression ratio.

Diesel Engine Combustion Sensing Methodology Based on Vibration Analysis

2014 ◽  
Vol 136 (11) ◽  
Author(s):  
Ponti Fabrizio ◽  
Ravaglioli Vittorio ◽  
Cavina Nicolò ◽  
De Cesare Matteo
Keyword(s):  
Diesel Engine ◽  
Closed Loop ◽  
Combustion Process ◽  
Pressure Sensors ◽  
Thermal Conditions ◽  
Pollutant Emissions ◽  
Accurate Estimation ◽  
Cylinder Pressure ◽  
Combustion Control ◽  
Real Time Analysis

The increasing request for pollutant emissions reduction spawned a great deal of research in the field of combustion control and monitoring. As a matter of fact, newly developed low temperature combustion strategies for diesel engines allow obtaining a significant reduction both in particulate matter and NOx emissions, combining the use of high EGR rates with a proper injection strategy. Unfortunately, due to their nature, these innovative combustion strategies are very sensitive to in-cylinder thermal conditions. Therefore, in order to obtain a stable combustion, a closed-loop combustion control methodology is needed. Many works demonstrate that a closed-loop combustion control strategy can be based on real-time analysis of in-cylinder pressure trace that provides important information about the combustion process, such as start of combustion, center of combustion and torque delivered by each cylinder. Nevertheless, cylinder pressure sensors on-board installation is still uncommon, due to problems related to unsatisfactory measurement long term reliability and cost. This paper presents a newly developed approach that allows extracting information about combustion effectiveness through the analysis of engine vibrations. In particular, the developed methodology can be used to obtain an accurate estimation of the indicated quantities of interest combining the information provided by engine speed fluctuations measurement and by the signals coming from acceleration transducers mounted on the engine. This paper also reports the results obtained applying the whole methodology to a light-duty turbocharged common rail diesel engine.

Effect of Mahua Biodiesel Blends on the Combustion Characteristics of Direct Injection CI Engine at Various Compression Ratios

2015 ◽  
Vol 813-814 ◽  
pp. 824-829
Author(s):  
Ramani Vagesh Shangar ◽  
Venkatesan Hariram
Keyword(s):  
Heat Release ◽  
Compression Ratio ◽  
Ignition Delay ◽  
Direct Injection ◽  
Combustion Characteristics ◽  
Cylinder Pressure ◽  
Biodiesel Blends ◽  
Peak Cylinder Pressure ◽  
Ci Engine ◽  
Mahua Biodiesel

In the current study, combustion characteristics were evaluated using mahua biodiesel blends at different compression ratios on a direct injection CI engine. Non edible mahua oil was transesterified into biodiesel by two stage technique. Combustion parameters were evaluated for B5, B10 and B20 blends of mahua biodiesel with diesel and they were compared with straight diesel at compression ratios of 16, 17 and 18.Compression ratio was varied without altering the combustion chamber geometry and the static spill timing was set to 23° bTDC. Parameters like In cylinder pressure, heat release rate, rate of pressure rise and cumulative heat release were evaluated in this study at 100% engine loading conditions. Higher peak cylinder pressure and heat release was observed at higher compression ratios. The ignition delay of the blends were slightly higher compared to diesel at all CR tested. Peak cylinder pressure of the blends was slightly higher at CR 18. The ignition delay was also observed to be lower at higher compression ratio. The peak pressure was observed closer to TDC at higher compression ratios for all fuels tested.

scholarly journals Flame Front and Burned Gas Characteristics for Different Split Injection Ratios and Phasing in an Optical GDI Engine

2019 ◽  
Vol 9 (3) ◽  
pp. 449 ◽  
Author(s):  
Santiago Martinez ◽  
Simona Merola ◽  
Adrian Irimescu
Keyword(s):  
Flame Front ◽  
Soot Formation ◽  
Direct Injection ◽  
Combustion Process ◽  
Pollutant Emissions ◽  
Optical Data ◽  
Cylinder Pressure ◽  
Split Injection ◽  
Gdi Engine ◽  
Injection Strategies

Direct-injection in spark-ignition engines has long been recognized as a valid option for improving fuel economy, reducing CO2 emissions and avoiding knock occurrence due to higher flexibility in control strategies. However, problems associated with mixture formation are responsible for soot emissions, one of the most limiting factors of this technology. Therefore, the combustion process and soot formation were investigated with different injection strategies on a gasoline direct injection (GDI) engine. The experimental analysis was realized on an optically accessible single cylinder engine when applying single, double and triple injection strategies. Moreover, the effect of fuel delivery phasing was also scrutinized by changing the start of the injection during late intake- and early compression-strokes. The duration of injection was split in different percentages between two or three pulses, so as to obtain close to stoichiometric operation in all conditions. The engine was operated at fixed rotational speed and spark timing, with wide-open throttle. Optical diagnostics based on cycle resolved digital imaging was applied during the early and late stages of the combustion process. Detailed information on the flame front morphology and soot formation were obtained. The optical data were correlated to in-cylinder pressure traces and exhaust gas emission measurements. The results suggest that the split injection of the fuel has advantages in terms of reduction of soot formation and NOx emissions and a similar combustion performance with respect to the single injection timing. Moreover, an early injection resulted in higher rates of heat release and in-cylinder pressure, together with a reduction of soot formation and flame distortion. The double injection strategy with higher percentage of fuel injected in the first pulse and early second injection pulse showed the best results in terms of combustion evolution and pollutant emissions. For the operative condition studied, a higher time for mixture homogenization and split of fuel injected in the intake stroke shows the best results.

scholarly journals Investigating Combustion Process of N-Butanol-Diesel Blends in a Diesel Engine with Variable Compression Ratio

2021 ◽  
Vol 3 (3) ◽  
pp. 618-628
Author(s):  
György Szabados ◽  
Kristóf Lukács ◽  
Ákos Bereczky
Keyword(s):  
Heat Release ◽  
Heat Release Rate ◽  
Compression Ratio ◽  
Release Rate ◽  
Ignition Delay ◽  
Alternative Fuels ◽  
Internal Combustion Engines ◽  
Combustion Process ◽  
Injection Angle ◽  
Combustion Properties

The search for alternative fuels for internal combustion engines is ongoing. Among the alternatives, plant-based fuels can also be mentioned. Alcohol is not a common fuel for diesel engines because the physical and chemical properties of the alcohols are closer to those of gasoline. In our research, the combustion properties of diesel-n-butanol mixtures have been investigated to obtain results on the effect of butanol blending on combustion. Among the combustion properties, ignition delay, in-cylinder pressure, and heat release rate can be mentioned. They have been observed under different compression conditions on an engine on which the compression ratio can be adjusted. The method used was a quite simple one, so the speed of the engine was set to a constant 900 rpm without load, while three compression ratios (19.92, 15.27, and 12.53) were adjusted with a fuel flow rate of 13 mL/min and the pre-injection angle of 18° BTDC. Blending butanol into the investigated fuel does not significantly affect maximal values of indicated pressure, while much more effect on the pressure rising rate can be detected. Furthermore, heat release rate and ignition delay increased at every compression ratio investigated. Despite the low blending rates of butanol in the mixtures, butanol significantly affects the combustion parameters, especially at high compression ratios.

Diesel Engine Combustion Sensing Methodology Based on Vibration Analysis

2013 ◽  
Author(s):  
F. Ponti ◽  
V. Ravaglioli ◽  
N. Cavina ◽  
M. De Cesare
Keyword(s):  
Diesel Engine ◽  
Closed Loop ◽  
Combustion Process ◽  
Pressure Sensors ◽  
Thermal Conditions ◽  
Pollutant Emissions ◽  
Accurate Estimation ◽  
Cylinder Pressure ◽  
Combustion Control ◽  
Real Time Analysis

The increasing request for pollutant emissions reduction spawned a great deal of research in the field of combustion control and monitoring. As a matter of fact, newly developed low temperature combustion strategies for Diesel engines allow obtaining a significant reduction both in particulate matter and NOx emissions, combining the use of high EGR rates with a proper injection strategy. Unfortunately, due to their nature, these innovative combustion strategies are very sensitive to in-cylinder thermal conditions. Therefore, in order to obtain a stable combustion, a closed-loop combustion control methodology is needed. Many works demonstrate that a closed-loop combustion control strategy can be based on real-time analysis of in-cylinder pressure trace, that provides important information about the combustion process, such as start of combustion, center of combustion and torque delivered by each cylinder. Nevertheless, cylinder pressure sensors on-board installation is still uncommon, due to problems related to unsatisfactory measurement long term reliability and cost. This paper presents a newly developed approach that allows extracting information about combustion effectiveness through the analysis of engine vibrations. In particular, the developed methodology can be used to obtain an accurate estimation of the indicated quantities of interest combining the information provided by engine speed fluctuations measurement and by the signals coming from acceleration transducers mounted on the engine. This paper also reports the results obtained applying the whole methodology to a light-duty turbocharged Common Rail Diesel engine.

Sign in / Sign up

Export Citation Format

Share Document