scholarly journals Development of a Novel Adsorbent Prepared from Dredging Sediment for Effective Removal of Dye in Aqueous Solutions

2021 ◽  
Vol 11 (22) ◽  
pp. 10722
Author(s):  
Abdelkader Ouakouak ◽  
Messameh Abdelhamid ◽  
Barhoumi Thouraya ◽  
Hadj-Otmane Chahinez ◽  
Grabi Hocine ◽  
...  
Keyword(s):  
Aqueous Solutions ◽  
Adsorption Process ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
Dye Adsorption ◽  
Isotherm Models ◽  
Effective Removal ◽  
Water Media ◽  
A Minor

This study proposed a novel and low-cost adsorbent prepared from dredging sediment (DSD) for effective removal of dye in aqueous solutions. The adsorption efficiency and behavior of the DSD adsorbent toward the crystal violet (CV), a cationic dye, were investigated via batch experiments. The results showed that DSD samples contain mainly clay minerals (illite and kaolinite) and other mineral phases. In addition, DSD is a mesoporous material (Vmesopore = 94.4%), and it exhibits a relatively high surface area (~39.1 m2/g). Adsorption experiments showed that the solution’s pH slightly affects the adsorption process, and a pH of 11 gave a maximum capacity of 27.2 mg/g. The kinetic data of CV dye adsorption is well described by the pseudo–second-order and the Avrami models. The Langmuir and Liu isotherm models provide the best fit for the adsorption equilibrium data. The monolayer adsorption capacity of Langmuir reached 183.6, 198.0, and 243.6 mg/g at 293, 308, and 323 K, respectively. It was also found that the adsorption process was spontaneous (−ΔG°), exothermic (−∆H°), and increased the randomness (+∆S°) during the adsorption operation. The primary mechanisms in CV dye adsorption were ion exchange and pore filling, whereas electrostatic attraction was a minor contribution. In addition, three steps involving intraparticle diffusion occur at the same time to control the adsorption process. The results of this study highlight the excellent efficiency of DSD material as an ecofriendly sorbent for toxic dyes from water media.

Treatment of textile industry effluents using orange waste: a proposal to reduce color and chemical oxygen demand

2016 ◽  
Vol 74 (4) ◽  
pp. 994-1004 ◽  
Author(s):  
Carlos Eduardo de Farias Silva ◽  
Andreza Heloiza da Silva Gonçalves ◽  
Ana Karla de Souza Abud
Keyword(s):  
Chemical Oxygen Demand ◽  
Textile Industry ◽  
Adsorption Process ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
Dye Adsorption ◽  
Oxygen Demand ◽  
Textile Wastewater ◽  
Color Removal

Various agricultural residues have been tested as biosorbents due to their low cost, high surface area, and favorable surface chemistry. In this work, a sweet orange albedo was tested as a biosorbent for treatment of real textile effluents. The orange albedo powder was prepared by drying the residue at 50 °C and milling to 30 mesh, and then used for dye adsorption from a alkaline (pH = 10.71) effluent. The adsorption process was studied in batch experiments at 30 °C by measuring color removal and chemical oxygen demand (COD). The color removal was found not to be significantly altered when the effluent was used in its raw state, while COD increased probably due to albedo degradation. For the effluent diluted to 60% (Veffluent VH2O−1), color and COD removal percentages of approximately 89% were obtained. It was found that pH played a very significant role on the adsorption process, as the treated albedo displayed a relative pHPZC* of 4.61, and the highest dye removal efficiencies were reached at pH lower than 2. The COD was strongly influenced by the effluent dilution. The effectiveness in eliminating color and COD shows that orange albedo can be potentially used as a biosorbent to treat textile wastewater.

scholarly journals Characterization of Residual Biomasses and Its Application for the Removal of Lead Ions from Aqueous Solution

2019 ◽  
Vol 9 (21) ◽  
pp. 4486 ◽  
Author(s):  
Candelaria Tejada-Tovar ◽  
Angel Darío Gonzalez-Delgado ◽  
Angel Villabona-Ortiz
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
High Surface ◽  
High Surface Area ◽  
Freundlich Isotherm ◽  
Mesoporous Structure ◽  
Isotherm Models ◽  
Solution Ph ◽  
Batch Mode ◽  
Suitable Alternative

The removal of water pollutants has been widely addressed for the conservation of the environment, and novel materials are being developed as adsorbent to address this issue. In this work, different residual biomasses were employed to prepare biosorbents applied to lead (Pb(II)) ion uptake. The choice of cassava peels (CP), banana peels (BP), yam peels (YP), and oil palm bagasse (OPB) was made due to the availability of such biomasses in the Department of Bolivar (Colombia), derived from agro-industrial activities. The materials were characterized by ultimate and proximate analysis, Fourier Transform Infrared Spectroscopy (FTIR), Brunauer-Emmett-Teller analysis (BET), Scanning Electron Microscopy (SEM), and Energy Dispersive X-Ray Spectroscopy (EDS) in order to determine the physicochemical properties of bioadsorbents. The adsorption tests were carried out in batch mode, keeping the initial metal concentration at 100 ppm, temperature at 30 °C, particle size at 1 mm, and solution pH at 6. The experimental results were adjusted to kinetic and isotherm models to determine the adsorption mechanism. The remaining concentration of Pb(II) in solution was measured by atomic absorption at 217 nm. The functional groups identified in FTIR spectra are characteristic of lignocellulosic materials. A high surface area was found for all biomaterials with the exception of yam peels. A low pore volume and size, related to the mesoporous structure of these materials, make these bioadsorbents a suitable alternative for liquid phase adsorption, since they facilitate the diffusion of Pb(II) ions onto the adsorbent structure. Both FTIR and EDS techniques confirmed ion precipitation onto adsorbent materials after the adsorption process. The adsorption tests reported efficiency values above 80% for YP, BP, and CP, indicating a good uptake of Pb(II) ions from aqueous solution. The results reported that Freundlich isotherm and pseudo-second order best fit experimental data, suggesting that the adsorption process is governed by chemical reactions and multilayer uptake. The future prospective of this work lies in the identification of alternatives to reuse Pb(II)-contaminated biomasses after heavy metal adsorption, such as material immobilization.

scholarly journals Development and study of iron-based nanoadsorbents

2004 ◽  
Vol 40 (1) ◽  
pp. 1-9 ◽  
Author(s):  
E. Deliyanni ◽  
D. Bakoyannakis ◽  
A. Zouboulis ◽  
K. Matis
Keyword(s):  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
Toxic Metal ◽  
Isotherm Models ◽  
Iron Hydroxides ◽  
X Ray Diffraction ◽  
Solution Ph ◽  
Prepared Material ◽  
Nanocrystalline Iron

The application of an innovative, simple and low cost method was tested for the preparation of nanocrystalline iron hydroxides and oxyhydroxides; different iron precursors have been earlier used and combined to different volatile precipitating agents. The examined in the present product, akagan?ite [?-FeO(OH)], had high surface area and definite pore size distribution. The produced materials were examined in detail (i.e. by powder X-ray diffraction, TEM and nitrogen sorption measurement). Main aim of this study was to evaluate the efficiency of the prepared material in the removal of heavy and toxic metal cations, like Cd(II), from aqueous solutions; cadmium constitutes a priority pollutant. Sorption was found to depended on the solution pH and its ionic strength. Typical isotherm models were applied and calculated the values of maximum adsorbent capacity for the metal as well as that of the enthalpy change during the removal process.

Kinetic, isotherm and thermodynamic aspects of Cu2+ biosorption onto Rosa damascena leaf as a low-cost biosorbent: Optimization of process variables by Response Surface Methodology

2021 ◽  
Author(s):  
Mustafa A. Fawzy ◽  
Hatim M. Al-Yasi ◽  
Tarek M. Galal ◽  
Reham Z. Hamza ◽  
Esmat F. Ali ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Aqueous Solutions ◽  
Response Surface ◽  
Structural Characteristics ◽  
Low Cost ◽  
High Surface ◽  
Isotherm Models ◽  
Rosa Damascena ◽  
Before And After ◽  
Leaf Powder

Abstract In this study, the Rosa damascena leaf powder was evaluated as a biosorbent for copper removal from aqueous solutions. Optimized conditions of 4.0 g/L biosorbent dosage, pH of 5.5 and initial copper concentration of 55 mg/L obtained by Response Surface Methodology were employed for Cu2+ biosorption by R. damascena leaves and up to 88.7 % Cu2+ was removed. The biosorption data were well fitted to the pseudo-second order and Elovich kinetic models. The Langmuir and Dubinin-Radushkevich isotherm models were also best fit the experimental data showing monolayer isotherm with qmax value of 25.13 mg/g obtained at optimum conditions. Thermodynamic parameters showed the spontaneity, feasibility and exothermic nature of adsorption. Scanning electron microscopy, Energy-Dispersive X-Ray, and Fourier transform infrared spectroscopy were used to characterize the biosorbent before and after Cu2+ biosorption, revealing outstanding structural characteristics and high surface functional groups availability. In addition, immobilized R. damascena leaves adsorbed 90.7 % of copper from aqueous solution, which is greater than free biosorbent (85.3 %). It can be concluded that R. damascena might be employed as a low-cost biosorbent for removing heavy metals from aqueous solutions.

Preparation and Characterization of Rice Husk Ash for Adsorption of Phenol from Aqueous Solutions

2014 ◽  
Vol 625 ◽  
pp. 498-502
Author(s):  
Samah B. Daffalla ◽  
Hilmi Mukhtar ◽  
Maizatul S. Shaharun
Keyword(s):  
Aqueous Solutions ◽  
Surface Area ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
Physiochemical Properties ◽  
Pseudo Second Order

In this research, the development of three (3) low-cost adsorbent materials from abundant waste rice husk was achieved via thermal treatment. The physiochemical properties of the developed adsorbents were evaluated. Their adsorption behaviours in batch system were evaluated for the removal of phenol from aqueous solutions by varying the pH (2 to 10). It was found that, the rice husk ash burned a 400oC for 1hr ‘RHA400,1’ has the highest surface area (201.36 m2.g-1) followed by RHA300,4(87.08 m2.g-1) and RHA600,1(43.22 m2.g-1), respectively. RHA400,1had shown the highest removal efficiency followed by RHA300,4and RHA600,1, towards phenol due to high surface area and porosity. The maximum uptake of phenol was found at pH 4. The adsorption kinetics was well described by both pseudo-second order and the Elovich models.

Dynamic Study of Adsorption for the Removal of Bismark Brown – Using Activated Carbons

2011 ◽  
Vol 671 ◽  
pp. 187-204
Author(s):  
A. Xavier ◽  
R Sathya ◽  
J. Gandhi Rajan ◽  
R. Nagarathnam
Keyword(s):  
Activated Carbon ◽  
Adsorption Process ◽  
Activated Carbons ◽  
Low Cost ◽  
Kinetic Equations ◽  
Dye Adsorption ◽  
Industrial Wastes ◽  
Isotherm Models ◽  
Before And After ◽  
Intra Particle Diffusion

Many industries use dyes and pigments to colorize their products. Large amount different types of dyes enter in to the environment. These dyes are invariably left in the industrial wastes. As a part of removal of Bismark Brown dye from textile and leather industrial wastes, using activated carbon as adsorbents namely, commercial activated carbon (CAC), rose apple carbon (RAC), coconut shell carbon (CSC) and saw dust carbon (SDC). The percentage removal of Bismark-Brown adsorbed increases with decrease in initial concentration and particle size of adsorbent and increased with increase in contact time, temperature and dose of adsorbent. The pH is highly sensitive for dye adsorption process. The adsorption process followed first order kinetics and the adsorption data with Freundlich and Langmuir isotherm models. The first kinetic equations like Natarajan Khalaf, Lagergren, Bhattacharya and Venkobhachar and intra-particle diffusion were found to be applicable. A comparative account of the adsorption capacity of various carbons has been made. These activated carbons are alternative to commercial AC for the removal dyes in General and Bismark-brown (BB) is particular. These results are reported highly efficient and effective and low cost adsorbent for the BB. The thermodynamics parameters are also studied and it obeys spontaneous process. The results are confirmed by before and after adsorption process with the help of the following instrumental techniques viz., FT-IR, UV-Visible Spectrophotometer and SEM analyze.

Adsorption of cefixime from aqueous solutions using modified hardened paste of Portland cement by perlite; optimization by Taguchi method

2016 ◽  
Vol 74 (5) ◽  
pp. 1069-1078 ◽  
Author(s):  
Mohammad Hossein Rasoulifard ◽  
Soghra Khanmohammadi ◽  
Azam Heidari
Keyword(s):  
Portland Cement ◽  
Aqueous Solutions ◽  
High Efficiency ◽  
Low Cost ◽  
Cost Effective ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Affecting Factors ◽  
Effective Removal ◽  
Removal Technique

In the present study, we have used a simple and cost-effective removal technique by a commercially available Fe-Al-SiO2 containing complex material (hardened paste of Portland cement (HPPC)). The adsorbing performance of HPPC and modified HPPC with perlite for removal of cefixime from aqueous solutions was investigated comparatively by using batch adsorption studies. HPPC has been selected because of the main advantages such as high efficiency, simple separation of sludge, low-cost and abundant availability. A Taguchi orthogonal array experimental design with an OA16 (45) matrix was employed to optimize the affecting factors of adsorbate concentration, adsorbent dosage, type of adsorbent, contact time and pH. On the basis of equilibrium adsorption data, Langmuir, Freundlich and Temkin adsorption isotherm models were also confirmed. The results showed that HPPC and modified HPPC were both efficient adsorbents for cefixime removal.

scholarly journals Lignin Based Activated Carbon Using H3PO4 Activation

Polymers ◽  
2020 ◽  
Vol 12 (12) ◽  
pp. 2829
Author(s):  
Zhongzhi Yang ◽  
Roland Gleisner ◽  
Doreen H. Mann ◽  
Junming Xu ◽  
Jianchun Jiang ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
Dye Adsorption ◽  
Nitrogen Adsorption ◽  
Bet Surface Area ◽  
Surface Areas ◽  
Adsorption Desorption

Activated carbon (AC) with a very high surface area of over 2000 m2/g was produced from low sulfur acid hydrotropic lignin (AHL) from poplar wood using H3PO4 at a moderate temperature of 450 °C (AHL-AC6). ACs with similar surface areas were also obtained under the same activation condition from commercial hardwood alkali lignin and lignosulfonate. Initial evaluation of AC performance was carried out using nitrogen adsorption-desorption and dye adsorption. AHL-AC6 exhibited the best specific surface area and dye adsorption performance. Furthermore, the adsorption results of congo red (CR) and methylene blue (MB) showed AHL-AC6 had greater adsorption capacity than those reported in literature. The dye adsorption data fit to the Langmuir model well. The fitting parameter suggests the adsorption is nearly strong and near irreversible, especially for MB. The present study for the first time provided a procedure for producing AC from lignin with Brunauer–Emmett–Teller (BET) surface area >2000 m2/g using low cost and low environmental impact H3PO4 at moderate temperatures.

scholarly journals Synthesis of catalysts with fine platinum particles supported by high-surface-area activated carbons and optimization of their catalytic activities for polymer electrolyte fuel cells

RSC Advances ◽  
2021 ◽  
Vol 11 (33) ◽  
pp. 20601-20611
Author(s):  
Md. Mijanur Rahman ◽  
Kenta Inaba ◽  
Garavdorj Batnyagt ◽  
Masato Saikawa ◽  
Yoshiki Kato ◽  
...  
Keyword(s):  
Fuel Cells ◽  
Polymer Electrolyte ◽  
High Performance ◽  
Activated Carbons ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
Polymer Electrolyte Fuel Cells ◽  
Supported Platinum ◽  
Platinum Particles

Herein, we demonstrated that carbon-supported platinum (Pt/C) is a low-cost and high-performance electrocatalyst for polymer electrolyte fuel cells (PEFCs).

Sign in / Sign up

Export Citation Format

Share Document