scholarly journals Lignin Based Activated Carbon Using H3PO4 Activation

Polymers ◽  
2020 ◽  
Vol 12 (12) ◽  
pp. 2829
Author(s):  
Zhongzhi Yang ◽  
Roland Gleisner ◽  
Doreen H. Mann ◽  
Junming Xu ◽  
Jianchun Jiang ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
Dye Adsorption ◽  
Nitrogen Adsorption ◽  
Bet Surface Area ◽  
Surface Areas ◽  
Adsorption Desorption

Activated carbon (AC) with a very high surface area of over 2000 m2/g was produced from low sulfur acid hydrotropic lignin (AHL) from poplar wood using H3PO4 at a moderate temperature of 450 °C (AHL-AC6). ACs with similar surface areas were also obtained under the same activation condition from commercial hardwood alkali lignin and lignosulfonate. Initial evaluation of AC performance was carried out using nitrogen adsorption-desorption and dye adsorption. AHL-AC6 exhibited the best specific surface area and dye adsorption performance. Furthermore, the adsorption results of congo red (CR) and methylene blue (MB) showed AHL-AC6 had greater adsorption capacity than those reported in literature. The dye adsorption data fit to the Langmuir model well. The fitting parameter suggests the adsorption is nearly strong and near irreversible, especially for MB. The present study for the first time provided a procedure for producing AC from lignin with Brunauer–Emmett–Teller (BET) surface area >2000 m2/g using low cost and low environmental impact H3PO4 at moderate temperatures.

Carbon Dioxide Adsorption Using High Surface Area Activated Carbons from Local Coals Modified by KOH, NaOH and ZnCl2 Agents

2017 ◽  
Vol 15 (3) ◽  
Author(s):  
Atakan Toprak ◽  
Turkan Kopac
Keyword(s):  
Surface Area ◽  
Activated Carbons ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
Micropore Volume ◽  
Bet Surface Area ◽  
Dft Methods ◽  
Surface Areas ◽  
Adsorption Capacities

Abstract Activated carbons of various features were produced by the impregnation of local coal samples that were taken from Kilimli region of Zonguldak (Turkey) with chemical agents KOH, NaOH and ZnCl2 at different temperatures (600–800 °C) and concentrations (1:1–6:1 agent:coal), for their evaluation in CO2 adsorption studies. BET, DR, t-plot and DFT methods were used for the characterization of carbon samples based on N2 adsorption data obtained at 77 K. The pore sizes of activated carbons produced were generally observed to be in between 13–25 Å, containing highly micropores. Mesopore formations were higher in samples treated with ZnCl2. The highest value for the BET surface area was found as 2,599 m2 g−1 for the samples treated with KOH at 800 °C with a KOH to coal ratio of 4:1. It was observed that the CO2 adsorption capacities obtained at atmospheric pressure and 273 K were considerably affected by the micropore volume and surface area. The highest CO2 adsorption capacities were found as 9.09 mmol/g (28.57 % wt) and 8.25 mmol g−1 (26.65 % wt) for the samples obtained with KOH and NaOH treatments, respectively, at ratio of 4:1. The activated carbons produced were ordered as KOH>NaOH>ZnCl2, according to their surface areas, micropore volumes and CO2 adsorption capacities. The low-cost experimental methods developed by the utilization of local coals in this study enabled an effective capture of CO2 before its emission to atmosphere.

Texture Evaluation of Sol-Gel Derived Mesoporous Bioactive Glass

2013 ◽  
Vol 284-287 ◽  
pp. 230-234
Author(s):  
Yu Jen Chou ◽  
Chi Jen Shih ◽  
Shao Ju Shih
Keyword(s):  
Surface Area ◽  
Calcination Temperature ◽  
High Surface ◽  
Sol Gel ◽  
High Surface Area ◽  
Nitrogen Adsorption ◽  
Bioactive Glasses ◽  
Transmission Electron ◽  
Sol Gel Process ◽  
Adsorption Desorption

Recent years mesoporous bioactive glasses (MBGs) have become important biomaterials because of their high surface area and the superior bioactivity. Various studies have reported that when MBGs implanted in a human body, hydroxyl apatite layers, constituting the main inorganic components of human bones, will form on the MBG surfaces to increase the bioactivity. Therefore, MBGs have been widely applied in the fields of tissue regeneration and drug delivery. The sol-gel process has replaced the conventional glasses process for MBG synthesis because of the advantages of low contamination, chemical flexibility and lower calcination temperature. In the sol-gel process, several types of surfactants were mixed with MBG precursor solutions to generate micelle structures. Afterwards, these micelles decompose to form porous structures after calcination. Although calcination is significant for contamination, crystalline and surface area in MBG, to the best of the authors’ knowledge, only few systematic studies related to calcination were reported. This study correlated the calcination parameters and the microstructure of MBGs. Microstructure evaluation was characterized by transmission electron microscopy and nitrogen adsorption/desorption. The experimental results show that the surface area and the pore size of MBGs decreased with the increasing of the calcination temperature, and decreased dramatically at 800°C due to the formation of crystalline phases.

Carbon Dioxide Sequestration Using Activated Carbon From Agro Waste-Waste Bamboo

2021 ◽  
Author(s):  
Emmanuel Ayodele ◽  
Victoria Ezeagwula ◽  
Precious Igbokwubiri
Keyword(s):  
Activated Carbon ◽  
Fly Ash ◽  
Greenhouse Gases ◽  
Surface Area ◽  
Carbon Capture ◽  
Agricultural Waste ◽  
High Surface ◽  
Research Work ◽  
High Surface Area ◽  
Bet Surface Area

Abstract Bamboo trees are one of the fastest growing trees in tropical rainforests around the world, they have various uses ranging from construction to fly ash generation used in oil and gas cementing, to development of activated carbon which is one of the latest uses of bamboo trees. This paper focuses on development of activated carbon from bamboo trees for carbon capture and sequestration. The need for improved air quality becomes imperative as the SDG Goal 12 and SDG Goal13 implies. One of the major greenhouse gases is CO2 which accounts for over 80% of greenhouse gases in the environment. Eliminating the greenhouse gases without adding another pollutant to the environment is highly sought after in the 21st century. Bamboo trees are mostly seen as agricultural waste with the advent of scaffolding and other support systems being in the construction industry. Instead of burning bamboo trees or using them for cooking in the local communities which in turn generates CO2 and fly ash, an alternative was considered in this research work, which is the usage of bamboo trees to generate activated, moderately porous and high surface area carbon for extracting CO2 from various CO2 discharge sources atmosphere and for water purification. This paper focuses on the quality testing of activated carbon that can effectively absorb CO2. The porosity, pore volume, bulk volume, and BET surface area were measured. The porosity of the activated carbon is 27%, BET surface area as 1260m²/g. Fixed carbon was 11.7%, Volatility 73%, ash content 1.7%.

scholarly journals Microporous activated carbon developed from KOH activated biomass waste: surface mechanistic study of methylene blue dye adsorption

2021 ◽  
Author(s):  
Ali H. Jawad ◽  
Ahmed Saud Abdulhameed ◽  
Noor Nazihah Bahrudin ◽  
Nurul Nadiah Mohd Firdaus Hum ◽  
S. N. Surip ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Surface Area ◽  
Sugarcane Bagasse ◽  
High Surface ◽  
High Surface Area ◽  
Dye Adsorption ◽  
Type I ◽  
Order Kinetic ◽  
Bagasse Waste

Abstract In this work, sugarcane bagasse waste (SBW) was used as a lignocellulosic precursor to develop a high surface area activated carbon (AC) by thermal treatment of the SBW impregnated with KOH. This sugarcane bagasse waste activated carbon (SBWAC) was characterized by means of crystallinity, porosity, surface morphology and functional groups availability. The SBWAC exhibited Type I isotherm which corresponds to microporosity with high specific surface area of 709.3 m2/g and 6.6 nm of mean pore diameter. Further application of SBWAC as an adsorbent for methylene blue (MB) dye removal demonstrated that the adsorption process closely followed the pseudo-second order kinetic and Freundlich isotherm models. On the other hand, thermodynamic study revealed the endothermic nature and spontaneity of MB dye adsorption on SBWAC with high acquired adsorption capacity (136.5 mg/g). The MB dye adsorption onto SBWAC possibly involved electrostatic interaction, H-bonding and π-π interaction. This work demonstrates SBW as a potential lignocellulosic precursor to produce high surface area AC that can potentially remove more cationic dyes from the aqueous environment.

Activated carbon fiber from liquefied wood and polyvinyl butyral as an additive for production of flexible all-carbon yarn supercapacitors

Holzforschung ◽  
2018 ◽  
Vol 72 (5) ◽  
pp. 367-374 ◽  
Author(s):  
Yuxiang Huang ◽  
Wenji Yu ◽  
Guangjie Zhao
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Carbon Fibers ◽  
High Surface ◽  
High Surface Area ◽  
Polyvinyl Butyral ◽  
Activated Carbon Fiber ◽  
Bet Surface Area ◽  
Liquefied Wood ◽  
New Material

AbstractA novel way to prepare mesoporous activated carbon fibers (ACFs-P) has been developed, while the ACFs-P with high surface area were obtained from liquefied wood by combining polyvinyl butyral (PVB) blending and steam activation. The porosity properties of the new material was investigated by N2adsorption and the Brunauer–Emmett–Teller (BET) surface area was found to be 2710 m2g−1and a pore volume of 1.540 cm3g−1, of which 58.2% was mesoporous with diameters between 3 and 6 nm. ACFs-P had a higher methylene blue (MB) adsorption capacity (962 mg/g) than the PVB-added carbon fibers (CFs-P) and ACFs-P without PVB (ACFs-C). Flexible all-carbon yarn supercapacitors can be produced from ACFs-P as powder or fiber. The fiber approach led to yarn supercapacitors with a less favorable electrochemical performance than the powder based production owing to the poor strength of the fibers. A 10 cm long yarn supercapacitor from the powdered ACFs exhibited a high specific length capacitance of 43 mF cm−1at 2 mV s−1. Yarn supercapacitors showed an excellent mechanical flexibility and its capacitor properties were not diminished after bending or crumpling.

Facile Synthesis of Activated Carbon from Swamp Taro Stalk via Single Step ZnCl2 Activation

2016 ◽  
Vol 857 ◽  
pp. 475-479 ◽  
Author(s):  
M.S. Mohammed Yahya ◽  
Jeyashelly Andas ◽  
Ghani Zaidi Ab
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
High Surface ◽  
High Surface Area ◽  
Total Pore Volume ◽  
Structure Type ◽  
Sem Analysis ◽  
Single Step ◽  
Bet Surface Area ◽  
Type Iv

In this work, mesoporous activated carbon with high surface area was synthesized from swamp taro stalk by single step ZnCl2 activation. The synthesized activated carbon was characterized by Na2S2O3 volumetric method, Fourier Transform Infrared Spectroscopy (FTIR), Scanning Electron Microscope (SEM) and N2 adsorption-desorption analyses. Under the single step ZnCl2 activation, the registered iodine number, BET surface area, total pore volume and pore diameter were 1087.57 mgg-1, 1242.26 m2g-1, 0.73cm3g-1 and 3.72 nm respectively with yield of 25.34%. SEM analysis evidenced the well-formation of porous structure. Type IV isotherm with H2 loops obtained from N2-sorption studies indicates the ink bottles shape mesoporous network structure. This research proved the successful conversion of plant waste into high grade activated carbon.

A comparison of different activated carbon performances on catalytic ozonation of a model azo reactive dye

2012 ◽  
Vol 66 (1) ◽  
pp. 179-184 ◽  
Author(s):  
Ş. Gül ◽  
O. Eren ◽  
Ş. Kır ◽  
Y. Önal
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Activated Carbons ◽  
High Surface ◽  
High Surface Area ◽  
Reactive Dye ◽  
Catalytic Ozonation ◽  
Bet Surface Area ◽  
Solution Ph ◽  
Pore Properties

The objective of this study is to compare the performances of catalytic ozonation processes of two activated carbons prepared from olive stone (ACOS) and apricot stone (ACAS) with commercial ones (granular activated carbon-GAC and powder activated carbon-PAC) in degradation of reactive azo dye (Reactive Red 195). The optimum conditions (solution pH and amount of catalyst) were investigated by using absorbencies at 532, 220 and 280 nm wavelengths. Pore properties of the activated carbon (AC) such as BET surface area, pore volume, pore size distribution, and pore diameter were characterized by N2 adsorption. The highest BET surface area carbon (1,275 m2/g) was obtained from ACOS with a particle size of 2.29 nm. After 2 min of catalytic ozonation, decolorization performances of ACOS and ACAS (90.4 and 91.3%, respectively) were better than that of GAC and PAC (84.6 and 81.2%, respectively). Experimental results showed that production of porous ACs with high surface area from olive and apricot stones is feasible in Turkey.

Low voltage electrolyte-gated organic transistors making use of high surface area activated carbon gate electrodes

2014 ◽  
Vol 2 (28) ◽  
pp. 5690-5694 ◽  
Author(s):  
J. Sayago ◽  
F. Soavi ◽  
Y. Sivalingam ◽  
F. Cicoira ◽  
C. Santato
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Low Voltage ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
Reference Electrode ◽  
Organic Transistors ◽  
Gate Electrodes ◽  
External Reference

The use of high surface area, low cost, activated carbon gate electrodes enables low voltage (sub-1 V) operation in ionic liquid-gated organic transistors and renders unnecessary the presence of an external reference electrode to monitor the channel potential.

scholarly journals The Role of the Aluminum Source on the Physicochemical Properties of γ-AlOOH Nanoparticles

2020 ◽  
Vol 39 (1) ◽  
pp. 89
Author(s):  
Rafael Romero Toledo ◽  
Luis M. Anaya Esparza ◽  
J. Merced Martínez Rosales
Keyword(s):  
Electron Microscopy ◽  
Physicochemical Properties ◽  
Surface Area ◽  
Low Cost ◽  
Nitrogen Adsorption ◽  
Bet Surface Area ◽  
Precipitation Method ◽  
X Ray ◽  
Aluminum Salts ◽  
Adsorption Desorption

The effect on the physicochemical properties of aluminum salts on the synthesis of γ-AlOOH nanostructures has been investigated in detail using a hydrolysis-precipitation method. X-ray fluorescence (XRF), Fourier transform infrared spectroscopy (FTIR), X-ray powder diffraction (XRD), field-emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM), were used to characterize the synthesized samples. The specific surface area, pore size distribution and pore diameter of the different γ-AlOOH structures were discussed by the N2 adsorption-desorption analysis. According to the results of the nanostructure, characterization revealed that for synthesized γ-AlOOH nanostructures from AlCl3 and Al(NO3)3, obvious XRD peaks corresponding to the bayerite phase are found indicating an impure γ-AlOOH phase. Furthermore, the nitrogen adsorption-desorption analysis indicated that the obtained γ-AlOOH nanoparticles from Al2(SO4)3 of technical grade (95.0 % of purity) and low cost, possess a high BET surface area of approximately 350 m2/g, compared to the obtained nanostructures from aluminum sources reactive grade, which was attributed to the presence of Mg (0.9 wt.%) in its nanostructure.

scholarly journals Modification of Microelectrode Arrays with High Surface Area Dendritic Platinum 3D Structures: Enhanced Sensitivity for Oxygen Detection in Ionic Liquids

Nanomaterials ◽  
2018 ◽  
Vol 8 (9) ◽  
pp. 735 ◽  
Author(s):  
Ghulam Hussain ◽  
Anthony O’Mullane ◽  
Debbie Silvester
Keyword(s):  
Surface Area ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
3D Structures ◽  
Surface Areas ◽  
Enhanced Sensitivity ◽  
Redox Active ◽  
Low Concentrations ◽  
One Step

Electrochemical gas sensors are often used for identifying and quantifying redox-active analyte gases in the atmosphere. However, for amperometric sensors, the current signal is usually dependent on the electroactive surface area, which can become small when using microelectrodes and miniaturized devices. Microarray thin-film electrodes (MATFEs) are commercially available, low-cost devices that give enhanced current densities compared to mm-sized electrodes, but still give low current responses (e.g., less than one nanoamp), when detecting low concentrations of gases. To overcome this, we have modified the surface of the MATFEs by depositing platinum into the recessed holes to create arrays of 3D structures with high surface areas. Dendritic structures have been formed using an additive, lead acetate (Pb(OAc)2) into the plating solution. One-step and two-step depositions were explored, with a total deposition time of 300 s or 420 s. The modified MATFEs were then studied for their behavior towards oxygen reduction in the room temperature ionic liquid (RTIL) [N8,2,2,2][NTf2]. Significantly enhanced currents for oxygen were observed, ranging from 9 to 16 times the current of the unmodified MATFE. The highest sensitivity was obtained using a two-step deposition with a total time of 420 s, and both steps containing Pb(OAc)2. This work shows that commercially-available microelectrodes can be favorably modified to give significantly enhanced analytical performances.

Sign in / Sign up

Export Citation Format

Share Document