scholarly journals Experimental Measurement of Residual Stress Distribution in Rail Specimens Using Ultrasonic LCR Waves

2021 ◽  
Vol 11 (19) ◽  
pp. 9306
Author(s):  
Young-In Hwang ◽  
Geonwoo Kim ◽  
Yong-Il Kim ◽  
Jeong-Hak Park ◽  
Man-Yong Choi ◽  
...  
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Residual Stresses ◽  
Stress Measurement ◽  
Residual Stress Distribution ◽  
Material Surface ◽  
Arrival Times ◽  
Effective Depth ◽  
The Difference ◽  
The Relationship

Longitudinal critically refracted (LCR) waves are considered bulk longitudinal waves and penetrate into an effective depth beneath the surface parallel to the material surface. Such LCR waves can be employed to measure residual stresses because the acoustoelastic effect is the basis for ultrasonic residual stress measurements. This effect is described by the relationship between change of wave travel time and stress applied when such waves propagate in a stressed medium. In this paper, stresses applied in a rail were evaluated by using a developed LCR probe. With this transducer, it was verified how the difference in the arrival times of the LCR waves showed a trend as the tensile stresses increased. The acoustoelastic coefficients were calculated using the relationship between the stresses and the travel times, and the residual stresses of the used rails were measured using these coefficients. In addition, the difference in residual stress distribution according to the characteristics of the wheel-rail contact surface was analyzed from the obtained residual stress value. It was concluded that this non-destructive evaluation technique using LCR waves could be employed for accurate stress measurement of rails because differences in stress applied to the rail can be detected.

Residual Stress Measurement on a Narrow Gap Dissimilar Metal Weld Pipe

2009 ◽  
Author(s):  
Xavier Ficquet ◽  
Laurie Chidwick ◽  
Philippe Gilles ◽  
Pierre Joly
Keyword(s):  
Residual Stress ◽  
Stainless Steel ◽  
Stress Distribution ◽  
Residual Stresses ◽  
Safety Assessment ◽  
Stress Measurement ◽  
Residual Stress Distribution ◽  
Narrow Gap ◽  
Mapping Procedure ◽  
Assessment Procedures

Prior knowledge of the magnitude and distribution of residual stresses in welded components is essential if a cost effective analyses of the integrity of the components is to be made. AREVA NP has recently developed, for EPR applications, narrow gap welding techniques, for joining ferritic low alloy steel heavy section components to austenitic, stainless steel piping systems, in nuclear reactors. An appraisal of available measurement methods was carried out and two residual stress measurement techniques were used to obtain through-thickness residual stress distributions in a fully circumferential narrow gap welded pipe, the neutron diffraction, which is not presented in this paper and the deep hole drilling (DHD) method. The DHD method was used to obtain the axial and hoop residual stresses along the weld centreline and on the heat affected zone in the ferritic and stainless steel sides up to depths of about 40mm from the outer surface of the pipe. The measured residual stress distribution in the weld centreline is compared with representative residual stress distribution provided in UK safety assessment procedures. It is found that the current safety assessment procedures BS 7910:2005 and R6 are conservative. The DHD measurements were made only at limited points in and adjacent to the circumferential weld. In order to estimate the complete residual stress distribution present in the pipe, a measurement mapping procedure using finite element (FE) analysis was implemented. Therefore this paper also provides the estimates of the full residual stress state present in the pipe based on the mapping procedure.

scholarly journals Employing the Waves to Measure Longitudinal Residual Stresses in Different Depths of a Stainless Steel Welded Plate

2013 ◽  
Vol 2013 ◽  
pp. 1-8 ◽  
Author(s):  
Yashar Javadi ◽  
Sergej Hloch
Keyword(s):  
Stainless Steel ◽  
Residual Stresses ◽  
Stress Measurement ◽  
Low Cost ◽  
Austenitic Stainless Steels ◽  
Material Surface ◽  
Effective Depth ◽  
Different Depths ◽  
The Relationship ◽  
The Waves

Ultrasonic stress measurement is based on the acoustoelasticity law which presents the relationship between the stress and acoustic wave velocity in engineering materials. The technique uses longitudinal critically refracted () waves that travel parallel to the material surface. The wave is a bulk longitudinal wave that propagates within an effective depth underneath the surface while the penetration depth of a wave depends on its frequency. It is possible to measure the residual stress in different depths by employing different frequencies of the waves. This paper evaluates welding residual stresses in different depths of a plate made of austenitic stainless steel (304L). The penetration depths are accurately measured for the waves produced by 1 MHz, 2 MHz, 4 MHz, and 5 MHz transducers. Residual stresses through the thickness of the plate are then evaluated by employing four different series of transducers. It has been concluded that the method is nondestructive, easy and fast, portable, readily available, and low cost and bulk measuring technique which can be accurately employed in through-thickness stress measurement of austenitic stainless steels.

Residual Stress Prediction by Means of 3D FEM Simulation

2011 ◽  
Vol 223 ◽  
pp. 431-438 ◽  
Author(s):  
Aldo Attanasio ◽  
Elisabetta Ceretti ◽  
Cristian Cappellini ◽  
Claudio Giardini
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Stress Measurement ◽  
Numerical Models ◽  
Orthogonal Cutting ◽  
Residual Stress Distribution ◽  
Tool Geometry ◽  
Distribution Analysis ◽  
3D Fem ◽  
Workpiece Material

In cutting field, residual stress distribution analysis on the workpiece is a very interesting topic. Indeed, the residual stress distribution affects fatigue life, corrosion resistance and other functional aspects of the workpiece. Recent studies showed that the development of residual stresses is influenced by the cutting parameters, tool geometry and workpiece material. For reducing the costs of experimental tests and residual stress measurement, analytical and numerical models have been developed. The aim of these models is the possibility of forecasting the residual stress distribution into the workpiece as a function of the selected process parameters. In this work the residual stress distributions obtained simulating cutting operations using a 3D FEM software and the corresponding simulation procedure are reported. In particular, orthogonal cutting operations of AISI 1045 and AISI 316L steels were performed. The FEM results were compared with the experimental residual stress distribution in order to validate the model effectiveness.

Theoretical prediction of residual stresses induced by cold spray with experimental validation

2019 ◽  
Vol 15 (3) ◽  
pp. 599-616 ◽  
Author(s):  
Dibakor Boruah ◽  
Xiang Zhang ◽  
Matthew Doré
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Residual Stresses ◽  
Cold Spray ◽  
Residual Stress Distribution ◽  
Thermal Mismatch ◽  
Individual Layer ◽  
Content Type ◽  
Layer Height ◽  
Proposed Model

PurposeThe purpose of this paper is to develop a simple analytical model for predicting the through-thickness distribution of residual stresses in a cold spray (CS) deposit-substrate assembly.Design/methodology/approachLayer-by-layer build-up of residual stresses induced by both the peening dominant and thermal mismatch dominant CS processes, taking into account the force and moment equilibrium requirements. The proposed model has been validated with the neutron diffraction measurements, taken from the published literature for different combinations of deposit-substrate assemblies comprising Cu, Mg, Ti, Al and Al alloys.FindingsThrough a parametric study, the influence of geometrical variables (number of layers, substrate height and individual layer height) on the through-thickness residual stress distribution and magnitude are elucidated. Both the number of deposited layers and substrate height affect residual stress magnitude, whereas the individual layer height has little effect. A good agreement has been achieved between the experimentally measured stress distributions and predictions by the proposed model.Originality/valueThe proposed model provides a more thorough explanation of residual stress development mechanisms by the CS process along with mathematical representation. Comparing to existing analytical and finite element methods, it provides a quicker estimation of the residual stress distribution and magnitude. This paper provides comparisons and contrast of the two different residual stress mechanisms: the peening dominant and the thermal mismatch dominant. The proposed model allows parametric studies of geometric variables, and can potentially contribute to CS process optimisation aiming at residual stress control.

A Further Study of Residual Stresses in Circumferential Welds

1973 ◽  
Vol 95 (4) ◽  
pp. 238-242 ◽  
Author(s):  
S. Vaidyanathan ◽  
H. Weiss ◽  
I. Finnie
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Residual Stresses ◽  
Base Metal ◽  
Filler Metal ◽  
Residual Stress Distribution ◽  
Experimental Results ◽  
Circumferential Welds ◽  
Single Pass ◽  
Full Penetration

The residual stress distribution for a circumferential weld between cylinders was obtained in a prior publication for a full penetration, single pass weld with no variation of alloy content across the weld. In the present work the approach is extended to cover a wider variety of weld conditions. It is shown that the effects of multipass welds, partial penetration welds, and welds with filler metal differing greatly in properties from the base metal can approximately be taken into account. Experimental results are presented to support the proposed method of analysis.

Measurement of Residual Stress Distribution of Ground Silicon Nitride by Glancing Incidence X-ray Diffraction Technique

1995 ◽  
Vol 39 ◽  
pp. 331-338
Author(s):  
Yoshihisa Sakaida ◽  
Keisuke Tanaka ◽  
Shintaro Harada
Keyword(s):  
Residual Stress ◽  
Surface Layer ◽  
Stress Distribution ◽  
Stress Measurement ◽  
Scintillation Counter ◽  
Ground Surface ◽  
Residual Stress Distribution ◽  
X Ray Diffraction ◽  
X Ray ◽  
Very High

A new method of X-ray stress measurement was proposed to estimate non-destructively the steep residual stress distribution in the surface layer of ground Si3N4. We assumed an exponential decrement of the residual stress near the ground surface, and derived a formula for the lattice strain as a function of sin2Ψ. In the experiments, the diffraction angles were measured on the ground surface for a widest possible range of sin2ѱ using an Ω-goniometer. In order to measure the diffraction angle at very high sin η values, a scintillation counter was located on the -η side and an incident X-ray beam impinged on the ground surface with a very low angle from the +η side using the glancing incidence X-ray diffraction technique. A strong non-linearity was found in the 20-sin2ѱ diagrams especially at very high ѱ -angles. From the analysis of non-linearity, the stress distribution in the surface layer was determined. Tine residual stress took the maximum compression of 2 GPa at a depth of about 0.5 μm from the surface, and then diminished to zero at about 25 μm in depth. In the close vicinity of the ground surface, the compressive residual stress was relieved because of both the surface roughness and microcracking induced during the grinding process.

Measurement of Residual Stresses within a PWR Swaged Heater Tube

2011 ◽  
Vol 70 ◽  
pp. 279-284 ◽  
Author(s):  
D.M. Goudar ◽  
Ed J. Kingston ◽  
Mike C. Smith ◽  
Sayeed Hossain
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Stress Measurement ◽  
Measurement Techniques ◽  
Residual Stress Distribution ◽  
Hole Drilling ◽  
Shear Stresses ◽  
Outer Diameter ◽  
Near Surface ◽  
Heater Tube

Frequent failures of the pressuriser heater tubes used in Pressurised Water Reactors (PWRs) have been found. Axial cracks initiating from the tube outer diameter have been detected in some tubes as well as the resulting electrical problems. Replacement of the heater tubes requires an undesirably prolonged plant shutdown. In order to better understand these failures a series of residual stress measurements were carried out to obtain the near surface and through-thickness residual stress profiles in a stainless steel pressuriser heater tube. Three different residual stress measurement techniques were employed namely, Deep-Hole Drilling (DHD), Incremental Centre Hole Drilling (ICHD) and Sachs’ Boring (SB) to measure the through thickness residual stress distribution in the heater tubes. Results showed that the hoop stresses measured using all three techniques were predominantly tensile at all locations, while the axial stresses were found to be tensile at the surface and both tensile and compressive as they reduce to small magnitudes within the tube. The magnitude of the in-plane shear stresses was small at all measurement depths at all locations. The various measurement methods were found to complement each other well. All the measurements revealed a characteristic profile for the through-thickness residual stress distribution.

scholarly journals Separation of the Formation Mechanisms of Residual Stresses in LPBF 316L

Metals ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1234
Author(s):  
Alexander Ulbricht ◽  
Simon J. Altenburg ◽  
Maximilian Sprengel ◽  
Konstantin Sommer ◽  
Gunther Mohr ◽  
...  
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Residual Stresses ◽  
Residual Stress Distribution ◽  
Formation Mechanisms ◽  
Micro Computed Tomography ◽  
Solidification Shrinkage ◽  
Stainless Steel 316L ◽  
Heat Accumulation ◽  
Cooling Rates

Rapid cooling rates and steep temperature gradients are characteristic of additively manufactured parts and important factors for the residual stress formation. This study examined the influence of heat accumulation on the distribution of residual stress in two prisms produced by Laser Powder Bed Fusion (LPBF) of austenitic stainless steel 316L. The layers of the prisms were exposed using two different border fill scan strategies: one scanned from the centre to the perimeter and the other from the perimeter to the centre. The goal was to reveal the effect of different heat inputs on samples featuring the same solidification shrinkage. Residual stress was characterised in one plane perpendicular to the building direction at the mid height using Neutron and Lab X-ray diffraction. Thermography data obtained during the build process were analysed in order to correlate the cooling rates and apparent surface temperatures with the residual stress results. Optical microscopy and micro computed tomography were used to correlate defect populations with the residual stress distribution. The two scanning strategies led to residual stress distributions that were typical for additively manufactured components: compressive stresses in the bulk and tensile stresses at the surface. However, due to the different heat accumulation, the maximum residual stress levels differed. We concluded that solidification shrinkage plays a major role in determining the shape of the residual stress distribution, while the temperature gradient mechanism appears to determine the magnitude of peak residual stresses.

scholarly journals Influence of Welding Defects on Residual Stresses: Numerical Study

2014 ◽  
Vol 996 ◽  
pp. 506-511
Author(s):  
Intissar Frih ◽  
Pierre Antoine Adragna ◽  
Guillaume Montay
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Residual Stresses ◽  
Numerical Study ◽  
Stress Gradient ◽  
Residual Stress Distribution ◽  
Welded Structure ◽  
Critical Defect ◽  
Welding Defects ◽  
Residual Stress Gradient

This paper presents a study on the application of the finite element methods to predict the influence of a defect on the residual stress distribution in a T-welded structure. A defect is introduced in a numerical model firstly without residual stress to see its impact (size and position) on the stress distribution. Secondly the most critical defect (determined previously) is simulated with a residual stress gradient. The obtained results are useful for computation stress concentration factor due to weld residual stresses.

Sign in / Sign up

Export Citation Format

Share Document