scholarly journals Shear Failure Mode and Concrete Edge Breakout Resistance of Cast-In-Place Anchors in Steel Fiber-Reinforced Normal Strength Concrete

2020 ◽  
Vol 10 (19) ◽  
pp. 6883
Author(s):  
Jong-Han Lee ◽  
Eunsoo Choi ◽  
Baik-Soon Cho
Keyword(s):  
Flexural Strength ◽  
Failure Mode ◽  
Shear Failure ◽  
Steel Fiber ◽  
Shear Resistance ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Embedment Depth ◽  
Fiber Reinforced ◽  
Tensile Performance

Concrete edge failure of a single anchor in concrete is strongly dependent on the tensile performance of the concrete, which can be greatly improved by the addition of steel fibers. This study investigated the effect of steel fibers on the shear failure mode and edge breakout resistance of anchors installed in steel fiber-reinforced concrete (SFRC) with fiber volume percentages of 0.33, 0.67, and 1.00%. The anchor used in the study was 30 mm in diameter, with an edge distance of 75 mm and embedment depth of 240 mm. In addition to the anchor specimens, beam specimens were prepared to assess the relationship between the tensile performance of SFRC beams and the shear resistance of SFRC anchors. The ultimate flexural strength of the beam and the breakout shear resistance of the anchor increased almost linearly with increasing volume fractions of fiber. Therefore, based on the ACI 318 design equation, a term was proposed using the ultimate flexural strength of concrete instead of the compressive strength to determine the concrete breakout shear resistance of an anchor in the SFRC. The calculated shear resistance of anchors in both the plain concrete and SFRC were in good agreement with the measurements. In addition to the load capacity of the SFRC anchors, the energy absorption capacity showed a linear increase with that of the SFRC beam.

On axial compressive behavior of steel fiber reinforced concrete confined by FRP

2021 ◽  
pp. 136943322098165
Author(s):  
Hossein Saberi ◽  
Farzad Hatami ◽  
Alireza Rahai
Keyword(s):  
Reinforced Concrete ◽  
Experimental Test ◽  
Steel Fiber ◽  
Experimental Tests ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Test Results ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Frp Confinement

In this study, the co-effects of steel fibers and FRP confinement on the concrete behavior under the axial compression load are investigated. Thus, the experimental tests were conducted on 18 steel fiber-reinforced concrete (SFRC) specimens confined by FRP. Moreover, 24 existing experimental test results of FRP-confined specimens tested under axial compression are gathered to compile a reliable database for developing a mathematical model. In the conducted experimental tests, the concrete strength was varied as 26 MPa and 32.5 MPa and the steel fiber content was varied as 0.0%, 1.5%, and 3%. The specimens were confined with one and two layers of glass fiber reinforced polymer (GFRP) sheet. The experimental test results show that simultaneously using the steel fibers and FRP confinement in concrete not only significantly increases the peak strength and ultimate strain of concrete but also solves the issue of sudden failure in the FRP-confined concrete. The simulations confirm that the results of the proposed model are in good agreement with those of experimental tests.

scholarly journals ANALYSIS OF PROPERTIES OF CONCRETE USING STEEL FIBERS AS FIBER REINFORCEMENT ADMIXTURE

2017 ◽  
Vol 5 (4RASM) ◽  
pp. 59-62
Author(s):  
Vishal Gadgihalli ◽  
Meena ◽  
Sindu ◽  
Raghavendra Prasad Dinakar
Keyword(s):  
Reinforced Concrete ◽  
Flexural Strength ◽  
Steel Fibre ◽  
Fiber Reinforcement ◽  
Paper Analysis ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Fiber Reinforced ◽  
Different Types ◽  
Discrete Uniform

Fiber reinforced concrete is composite material consisting of mixtures of cement, mortar or concrete, discontinuous discrete uniform dispersed suitable fibers. Fiber reinforced concrete are of different types and properties. In this paper analysis of properties of concrete using steel fibre as fiber reinforcement admixture is studied and verified the strength of concrete to normal plane concrete with absence of admixtures. Using steel fibers as fiber reinforcement admixture increases bond strength by enhancing surface tension as steel is better in taking flexural strength this gives better results, hence we can use this steel fiber reinforcement to concrete where the compressive and flexural strength place a crucial role in construction and maintenance.

Study on Retrofitting and Strengthening of Reinforced Concrete Beams Using Fibrous Concrete

2021 ◽  
Vol 9 (8) ◽  
pp. 1676-1684
Author(s):  
Natalia Sharma
Keyword(s):  
Mechanical Properties ◽  
Reinforced Concrete ◽  
Steel Fiber ◽  
Concrete Beams ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Reinforced Concrete Beams ◽  
Cement Matrix ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete

Abstract: Reinforced concrete structures are frequently in need of repair and strengthening as a result of numerous environmental causes, ageing, or material damage under intense stress conditions, as well as mistakes made during the construction process. RC structures are repaired using a variety of approaches nowadays. The usage of FRC is one of the retrofitting strategies. Steel fiber reinforced concrete (SFRC) was used in this investigation because it contains randomly dispersed short discrete steel fibers that operate as internal reinforcement to improve the cementitious composite's characteristics (concrete). The main rationale for integrating small discrete fibers into a cement matrix is to reduce the amount of cement used. The principal reason for incorporating short discrete fibers into a cement matrix is to reduce cracking in the elastic range, increase the tensile strength and deformation capacity and increase the toughness of the resultant composite. These properties of SFRC primarily depend upon length and volume of Steel fibers used in the concrete mixture. In India, the steel fiber reinforced concrete (SFRC) has seen limited applications in several structures due to the lack of awareness, design guidelines and construction specifications. Therefore, there is a need to develop information on the role of steel fibers in the concrete mixture. The experimental work reported in this study includes the mechanical properties of concrete at different volume fractions of steel fibers. These mechanical properties include compressive strength, split tensile strength and flexural strength and to study the effect of volume fraction and aspect ratio of steel fibers on these mechanical properties. However, main aim of the study was significance of reinforced concrete beams strengthened with fiber reinforced concrete layer and to investigate how these beams deflect under strain. The objective of the investigation was finding that applying FRC to strengthen beams enhanced structural performance in terms of ultimate load carrying capacity, fracture pattern deflection, and mode of failure or not.

Punching Shear Capacity of Steel Fiber Reinforced Concrete Slab- Column Connections

2019 ◽  
Author(s):  
Josef Landler ◽  
Oliver Fischer
Keyword(s):  
Reinforced Concrete ◽  
Steel Fiber ◽  
Fiber Type ◽  
Fiber Content ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Punching Shear ◽  
Slab Thickness ◽  
Shear Reinforcement ◽  
Fiber Reinforced

<p>To design flat slabs directly supported on columns, the punching shear resistance of the slab is a main factor. It can be increased in the vicinity of the slab-column connection with punching shear reinforcement, like bent up bars or shear studs, to bear the high reaction forces. However, the usage of punching shear reinforcement requires the knowledge of special design rules and often leads to problems and deficiencies in construction.</p><p>Fiber reinforced concrete seems to be a promising alternative to conventional punching shear reinforcement. To investigate the load bearing behavior of the slab-column connection using fiber reinforced concrete, a total of eight punching shear tests were performed. The specimens were realized with a typical top and bottom flexural reinforcement, but without punching shear reinforcement. Varied parameters were the slab thickness with 250 mm and 300 mm and the fiber content V<sub>f</sub> with 0.5 Vol.-% and 1.0 Vol.-%. To investigate the influence of modern fiber types, normal- and high-strength steel fibers with normal- and double-hooked-ends were used.</p><p>In all eight experimental tests, the intended punching shear failure was achieved. The capable load using fiber reinforced concrete increased by 20 % to 50 % compared to the reference tests without steel fibers, depending on the fiber type and the fiber content V<sub>f</sub>. Additionally, this load increase was accompanied by a significant improvement in ductility. The post-cracking behavior was noticeably influenced by the used steel fiber type. An influence of the slab thickness or steel fiber type on the shear strength contributed by the fiber reinforced concrete could not be determined.</p>

Experimental Study on Rate-Dependent of the Bending Tensile Properties for Steel Fiber Reinforced Concrete

2011 ◽  
Vol 71-78 ◽  
pp. 1083-1089
Author(s):  
Zhang Luo
Keyword(s):  
Reinforced Concrete ◽  
Flexural Strength ◽  
Strain Rate ◽  
Tensile Properties ◽  
Steel Fiber ◽  
Fiber Reinforced Concrete ◽  
Test Machine ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Rate Dependent

Extensive experimental research has been done on rate-dependent properties normal concrete, but very little on the tensile properties of steel fiber reinforced concrete (SFRC). In this article, based on a high-speed Instron servo-controlled hydraulic materials test machine is adopted to investigate the strain rate-dependent properties of bending tensile properties for SFRC. The scheme of experiment, the works of specimens fabricating and the processes of both loading and measuring were introduced. A total of 30 beam specimens are tested. The steel fiber content is varied: 0%, 1.0%, 2.0%, 3.0% and 4.0% by volume. The experimental results were analyzed. The emphasis is put on the study of the flexural strength changes of SFRC under different strain rates. It is discovered that, with the improvement of the strain rate, increasing strength of SFRC is very obvious. While the strain rate increases from 1.4×10-4s-1 to 0.53×10-4s-1, the flexural strength increasing around 30%.

scholarly journals Microscale Cohesive-Friction-Based Finite Element Model for the Crack Opening Mechanism of Hooked-End Steel Fiber-Reinforced Concrete

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 669
Author(s):  
Yassir M. Abbas
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Steel Fiber ◽  
Crack Opening ◽  
Fiber Reinforced Concrete ◽  
Embedment Depth ◽  
Fe Model ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Fiber Matrix

The entire mechanical properties of steel fiber-reinforced concrete (SFRC) are significantly dependent on the fiber–matrix interactions. In the current study, a finite element (FE) model was developed to simulate the pullout response of hooked-end SFRC employing cohesive–frictional interactions. Plain stress elements were adapted in the model to exemplify the fiber process constituents, taking into consideration the material nonlinearity of the hooked-end fiber. Additionally, a surface-to-surface contact model was used to simulate the fiber’s behavior in the pullout mechanism. The model was calibrated against experimental observations, and a modification factor model was proposed to account for the 3D phenomenalistic behavior of the pullout behavior. Realistic predictions were obtained by using this factor to predict the entire pullout-slip curves and independent results for the peak pullout load. The numerical results indicated that the increased fiber diameter would alter the mode of crack opening from fiber–matrix damage to that combined with matrix spalling, which can neutralize the sensitivity of the entire pullout response of hooked-end steel fiber to embedment depth. Additionally, the fiber–matrix bond was enhanced by increasing the fiber’s surface area, sensibly leading to a higher pullout peak load and toughness. The developed FE model was also proficient in predicting microstructural stress distribution and deformations during the crack opening of SFRC. This model could be extended to fully model a loaded SFRC composite material by the inclusion of various randomly oriented dosages of fibers in the concrete block.

Bending Toughness of Zinc Phosphate Steel Fiber Reinforced Concrete before and after Corrosion

2010 ◽  
Vol 168-170 ◽  
pp. 1762-1766
Author(s):  
Min Sun ◽  
Di Jiang Wen ◽  
Peng Xie
Keyword(s):  
Reinforced Concrete ◽  
Zinc Phosphate ◽  
Steel Fiber ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Before And After ◽  
Interface Bond Strength ◽  
Interface Bond

The interface bond between steel fibers and concrete matrix is the key of carrying capacity of steel fiber reinforced concrete(SFRC). In marine tidal fluctuation zone and splashed area, steel fibers will be rusty, and the bending toughness of SFRC was weakened. In this study, we tried to improve corrosion resistance of steel fiber and the interface bond strength by depositing zinc phosphate coating on steel fiber. These zinc phosphate steel fiber reinforced concrete(ZSFRC) have higher anti-corrosion ability. After corrosion they still have higher bending toughness than common SFRC.

Sign in / Sign up

Export Citation Format

Share Document