scholarly journals Experimental Investigations of Different Loudspeakers Applied as Synthetic Jet Actuators

Actuators ◽  
2021 ◽  
Vol 10 (9) ◽  
pp. 224
Author(s):  
Paweł Gil ◽  
Joanna Wilk
Keyword(s):  
Thermal Resistance ◽  
Resonance Frequency ◽  
Sound Pressure Level ◽  
Heat Sink ◽  
Sound Pressure ◽  
Pressure Level ◽  
Synthetic Jet ◽  
Experimental Investigations ◽  
Driving Frequency ◽  
Jet Velocity

The paper presents the preliminary results of the experimental investigation of four various loudspeakers used for driving the synthetic jet actuator. The parameters, characteristic synthetic jet velocity, pressure inside the cavity, device sound pressure level (SPL), and the heat sink thermal resistance, were presented for various input power and driving frequency. The resonance frequency was determined based on electrical impedance. The highest synthetic jet momentum velocity was achieved at diaphragm resonance frequency. The maximum sound pressure level was observed, also at resonant frequency. For the same real power delivered to the actuator and for its resonance frequency, the heat sink thermal resistance had the lowest value for the specific loudspeaker. In turn, the synthetic jet velocity reached maximum for this actuator. For all actuators tested, the sound pressure level was dependent on momentum velocity.

scholarly journals Acoustic and Flow Aspects of Novel Synthetic Jet Actuator

Actuators ◽  
2020 ◽  
Vol 9 (4) ◽  
pp. 100 ◽  
Author(s):  
Emil Smyk ◽  
Paweł Gil ◽  
Rafał Gałek ◽  
Łukasz Przeszłowski
Keyword(s):  
Sound Pressure Level ◽  
Sound Pressure ◽  
Optimal Solution ◽  
Sound Level ◽  
Pressure Level ◽  
Synthetic Jet ◽  
Acoustic Properties ◽  
Synthetic Jet Actuator ◽  
Flow Parameters ◽  
Level Meter

The acoustic and flow aspects of the novel synthetic jet actuator (SJA) with fins inside the cavity were experimentally investigated for three types of enclosure design and two models of loudspeaker. The aim of the study is to find the parameter which connects the flow and acoustic properties of the SJA and allows us to choose the optimal solution in those regards. The hot wire anemometry was used for the velocity measurements and the sound pressure level was measured with a sound level meter. The model of the loudspeaker turned out to have a significantly stronger impact on the flow parameters and noise level than the shape of the fins in the cavity. The parameter that showed a dependence on the shape of the fins was the actuator’s efficiency. A ratio of the root-mean-square velocity at the orifice axis to the sound pressure level (U0.c/SPL) was used to connect the acoustic and flow properties of the tested actuators. This parameter was subsequently applied to determine the best configuration among the tested actuators.

scholarly journals Acoustic and Flow Aspects of Synthetic Jet Actuators with Chevron Orifices

2021 ◽  
Vol 11 (2) ◽  
pp. 652
Author(s):  
Emil Smyk ◽  
Marek Markowicz
Keyword(s):  
Noise Reduction ◽  
Sound Pressure Level ◽  
Sound Pressure ◽  
Pressure Level ◽  
Synthetic Jet ◽  
Synthetic Jets ◽  
Nozzle Orifice ◽  
Circular Orifice ◽  
Chevron Nozzle ◽  
The Impact

The use of a chevron nozzle/orifice is one of the methods of heat transfer enhancement and noise reduction. In the case of synthetic jets, the number of papers on this topic is small. Therefore, a synthetic jet actuator with three different chevron orifices and one circular orifice is investigated. The aim of this study is to find the impact of orifice shape on centerline velocity (measured with a hot-wire anemometer) and determine if the chevron orifice reduces the generated noise. The sound pressure level was strongly dependent on the input actuator’s power, and only one chevron orifice ensured noise reduction for low power (p = 6; 8 W). At real power p = 12 W, the sound pressure level was lower for each chevron orifice actuator than in the case of the circular orifice actuator. It is shown that the application of a chevron nozzle does not have to provide noise reduction. It is important in the case of the design of new actuators that are to operate in places where noise levels should be limited (e.g., offices).

On the acoustic levitation of droplets

1998 ◽  
Vol 356 ◽  
pp. 65-91 ◽  
Author(s):  
A. L. YARIN ◽  
M. PFAFFENLEHNER ◽  
C. TROPEA
Keyword(s):  
Sound Pressure Level ◽  
Sound Pressure ◽  
Pressure Level ◽  
Experimental Investigations ◽  
Acoustic Levitation ◽  
Rigid Sphere ◽  
Rigid Spheres ◽  
Droplet Shape ◽  
Method Of Calculation ◽  
Theoretical Approaches

This paper deals with the theoretical and experimental investigation of acoustically levitated droplets. A method of calculation of the acoustic radiation pressure based on the boundary element method (BEM) is presented. It is applied to predict shapes of droplets levitated in an acoustic field (and as a result, deformed by it). The method was compared with several known exact and approximate analytical results for rigid spheres and shown to be accurate (and a widely used approximate formula for the acoustic levitation force acting on a rigid sphere was found to be inaccurate for sound wavelengths comparable with the sphere radius). The method was also compared with some other theoretical approaches known from the literature.Displacement of the droplet centre relative to the pressure node is accounted for and shown to be significant. The results for droplet shapes and displacements are compared with experimental data, and the agreement is found to be rather good. Furthermore, the experimental investigations reveal a unique relationship between the aspect ratio of an oblate droplet and the sound pressure level in the levitator. This relationship agrees well with the predicted shapes. A practical link between droplet shape or droplet displacement and sound pressure level in a levitator is therefore now available.

Contributions of Voice and Nonverbal Communication to Perceived Masculinity–Femininity for Cisgender and Transgender Communicators

2020 ◽  
Vol 63 (4) ◽  
pp. 931-947
Author(s):  
Teresa L. D. Hardy ◽  
Carol A. Boliek ◽  
Daniel Aalto ◽  
Justin Lewicke ◽  
Kristopher Wells ◽  
...  
Keyword(s):  
Fundamental Frequency ◽  
Sound Pressure Level ◽  
Sound Pressure ◽  
Vocal Tract ◽  
Presentation Mode ◽  
Pressure Level ◽  
Presentation Modes ◽  
Audiovisual Stimuli ◽  
Vocal Tract Resonance ◽  
Point Light

Purpose The purpose of this study was twofold: (a) to identify a set of communication-based predictors (including both acoustic and gestural variables) of masculinity–femininity ratings and (b) to explore differences in ratings between audio and audiovisual presentation modes for transgender and cisgender communicators. Method The voices and gestures of a group of cisgender men and women ( n = 10 of each) and transgender women ( n = 20) communicators were recorded while they recounted the story of a cartoon using acoustic and motion capture recording systems. A total of 17 acoustic and gestural variables were measured from these recordings. A group of observers ( n = 20) rated each communicator's masculinity–femininity based on 30- to 45-s samples of the cartoon description presented in three modes: audio, visual, and audio visual. Visual and audiovisual stimuli contained point light displays standardized for size. Ratings were made using a direct magnitude estimation scale without modulus. Communication-based predictors of masculinity–femininity ratings were identified using multiple regression, and analysis of variance was used to determine the effect of presentation mode on perceptual ratings. Results Fundamental frequency, average vowel formant, and sound pressure level were identified as significant predictors of masculinity–femininity ratings for these communicators. Communicators were rated significantly more feminine in the audio than the audiovisual mode and unreliably in the visual-only mode. Conclusions Both study purposes were met. Results support continued emphasis on fundamental frequency and vocal tract resonance in voice and communication modification training with transgender individuals and provide evidence for the potential benefit of modifying sound pressure level, especially when a masculine presentation is desired.

Case study: Theoretical calculation model and variable condition analysis research on the water-splashing noise for natural draft wet cooling towers

2020 ◽  
Vol 68 (2) ◽  
pp. 137-145
Author(s):  
Yang Zhouo ◽  
Ming Gao ◽  
Suoying He ◽  
Yuetao Shi ◽  
Fengzhong Sun
Keyword(s):  
Theoretical Model ◽  
Sound Pressure Level ◽  
Water Droplet ◽  
Water Distribution ◽  
Sound Pressure ◽  
Cooling Tower ◽  
Distribution Patterns ◽  
Calculation Model ◽  
Pressure Level ◽  
Cooling Towers

Based on the basic theory of water droplets impact noise, the generation mechanism and calculation model of the water-splashing noise for natural draft wet cooling towers were established in this study, and then by means of the custom software, the water-splashing noise was studied under different water droplet diameters and water-spraying densities as well as partition water distribution patterns conditions. Comparedwith the water-splashing noise of the field test, the average difference of the theoretical and the measured value is 0.82 dB, which validates the accuracy of the established theoretical model. The results based on theoretical model showed that, when the water droplet diameters are smaller in cooling tower, the attenuation of total sound pressure level of the water-splashing noise is greater. From 0 m to 8 m away from the cooling tower, the sound pressure level of the watersplashing noise of 3 mm and 6 mm water droplets decreases by 8.20 dB and 4.36 dB, respectively. Additionally, when the water-spraying density becomes twice of the designed value, the sound pressure level of water-splashing noise all increases by 3.01 dB for the cooling towers of 300 MW, 600 MW and 1000 MW units. Finally, under the partition water distribution patterns, the change of the sound pressure level is small. For the R s/2 and Rs/3 partition radius (Rs is the radius of water-spraying area), when the water-spraying density ratio between the outer and inner zone increases from 1 to 3, the sound pressure level of water-splashing noise increases by 0.7 dB and 0.3 dB, respectively.

Sign in / Sign up

Export Citation Format

Share Document