scholarly journals Comparison of Novel Seismic Protection Devices to Attenuate the Earthquake Induced Energy

Actuators ◽  
2021 ◽  
Vol 10 (4) ◽  
pp. 73
Author(s):  
Osman Hansu ◽  
Esra Mete Güneyisi
Keyword(s):  
Lateral Displacement ◽  
Time History ◽  
Seismic Protection ◽  
Base Shear ◽  
Seismic Demands ◽  
Nonlinear Time History Analyses ◽  
History Of ◽  
Protection Devices ◽  
Nonlinear Time History ◽  
Better Than

This study addresses an alternative use of viscous dampers (VDs) associated with buckling restrained braces (BRBs) as innovative seismic protection devices. For this purpose, 4-, 8- and 12-story steel bare frames were designed with 6.5 m equal span length and 4 m story height. Thereafter, they were seismically improved by mounting the VDs and BRBs in three patterns, namely outer bays, inner bays, and all bays over the frame heights. The structures were modeled using SAP 2000 software and evaluated by the nonlinear time history analyses subjected to the six natural ground motions. The seismic responses of the structures were investigated for the lateral displacement, interstory drift, absolute acceleration, maximum base shear, and time history of roof displacement. The results clearly indicated that the VDs and BRBs reduced seismic demands significantly compared to the bare frame. Moreover, the all-bay pattern performed better than the others.

Influence of Earthquake Attack Angle on Seismic Demands for Structures under Bi-Directional Ground Motions

2011 ◽  
Vol 255-260 ◽  
pp. 2330-2334 ◽  
Author(s):  
Yu Zhang ◽  
Quan Wang Li ◽  
Jian Sheng Fan
Keyword(s):  
Seismic Design ◽  
Ground Motions ◽  
Time History ◽  
Earthquake Excitation ◽  
Seismic Demands ◽  
3 Dimensional ◽  
Nonlinear Time History Analyses ◽  
Modification Factor ◽  
Structural Responses ◽  
Nonlinear Time History

The earthquake may attack the structural building from any angle, but in current seismic design codes, this type of uncertainty is seldom accounted. The uncertainty associated with the direction of earthquake excitation was considered in this paper, and its effect on structural responses was investigated. For this purpose, a simple 3-dimensional model with symmetric plan was established, which had fundamental periods ranged from 0.1s to 5.0s, and was subjected to a set of 30 ground motion pairs for which both linear and nonlinear time history analyses were performed. Analyzing results showed that, on average, the elastic roof acceleration is 32% underestimated, and the inelastic roof displacement is 18% underestimated if the variation of earthquake excitation direction is not consider. Recognizing this, a modification factor for the seismic demand was proposed thorough a statistical analysis, which guarantees a probability of 95% design safety

scholarly journals Spectral Assessment of the Effects of Base Flexibility on Seismic Demands of a Structure

2016 ◽  
Vol 2016 ◽  
pp. 1-8
Author(s):  
J. Borzouie ◽  
J. G. Chase ◽  
G. A. MacRae ◽  
G. W. Rodgers ◽  
G. C. Clifton
Keyword(s):  
Lateral Displacement ◽  
Time History ◽  
Nonlinear Time History Analysis ◽  
Seismic Demand ◽  
Rotational Stiffness ◽  
Earthquake Excitation ◽  
Seismic Demands ◽  
Fixed Base ◽  
Linear And Nonlinear ◽  
Nonlinear Time History

Base flexibility of structures changes and can increase the demands on structural elements during earthquake excitation. Such flexibility may come from the base connection, foundation, and soil under the foundation. This research evaluates the effects of column base rotational stiffness on the seismic demand of single storey frames with a range of periods using linear and nonlinear time history analysis. The base rotational stiffness ranges considered are based on previous studies considering foundation and baseplate flexibility. Linear and nonlinear spectral analyses show that increasing base flexibility generally increases frame lateral displacement and top moment of the column. Furthermore, moments at the top of the columns and the nonlinear base rotation may also increase with increasing base flexibility, especially for shorter period structures. Since many commonly used baseplate connections may be categorized as being semirigid, it is essential to design and model structures using realistic base rotational stiffness rather than simply use a fixed base assumption. The overall results also illustrate the range of increased seismic demand as a function of normalized rotational stiffness and structural period for consideration in design.

scholarly journals Seismic Performance of a Green Roof Structure

2021 ◽  
Vol 13 (8) ◽  
pp. 4278
Author(s):  
Svetlana Tam ◽  
Jenna Wong
Keyword(s):  
Green Roof ◽  
Time History ◽  
Green Roofs ◽  
Moment Frame ◽  
Steel Moment Frame ◽  
Roof Structure ◽  
Nonlinear Time History Analyses ◽  
Vegetated Roofs ◽  
Nonlinear Time History ◽  
The Impact

Sustainability addresses the need to reduce the structure’s impact on the environment but does not reduce the environment’s impact on the structure. To explore this relationship, this study focuses on quantifying the impact of green roofs or vegetated roofs on seismic responses such as story displacements, interstory drifts, and floor level accelerations. Using an archetype three-story steel moment frame, nonlinear time history analyses are conducted in OpenSees for a shallow and deep green roof using a suite of ground motions from various distances from the fault to identify key trends and sensitivities in response.

Second Paper: Deep Drawing and Free Forming Using a Water Hammer Technique

1964 ◽  
Vol 179 (1) ◽  
pp. 222-233 ◽  
Author(s):  
A. P. Vafiadakis ◽  
W. Johnson ◽  
I. S. Donaldson
Keyword(s):  
Deep Drawing ◽  
Time History ◽  
Water Hammer ◽  
High Rate ◽  
Pressure Time ◽  
Order Of Magnitude ◽  
History Of ◽  
Overall Efficiency ◽  
Initial Movement ◽  
Better Than

Earlier work on a water-hammer technique for high-rate forming of sheet metal has been extended to include work on deep drawing using lead plugs. A study of the pressure-time history of a deforming blank during its initial movement is reported. An assessment of the overall efficiency of the process has been made and is found to be about 50 per cent; this is an order of magnitude better than that found with comparable electro-hydraulic and explosive methods.

scholarly journals A simple method for determining seismic demands on gravity load frames

2017 ◽  
Vol 44 (8) ◽  
pp. 661-673 ◽  
Author(s):  
J. Beauchamp ◽  
P. Paultre ◽  
P. Léger
Keyword(s):  
Response Spectrum ◽  
Time History ◽  
Bending Moment ◽  
New Method ◽  
Simple Method ◽  
Seismic Demands ◽  
Gravity Load ◽  
Comparison Results ◽  
Seismic Force ◽  
Nonlinear Time History

This paper presents a simple method based on modal response spectrum analysis to compute internal forces in structural elements belonging to gravity framing not part of the seismic force resisting system (SFRS). It is required that demands on these gravity load resisting system (GLRS) be determined according to the design displacement profile of the SFRS. The proposed new method uses the fact that if the linear stiffness properties of the GLRS not part of the SFRS have negligible values compared to those of the SFRS, only the latter will provide lateral resistance. Displacements of the GLRS then correspond to those of the SFRS alone. The new method is illustrated by computing the seismic responses of a symmetric and an asymmetric multi-storey reinforced concrete building. These results are compared to those obtained from the application of the simplified analysis method proposed in the Canadian standard for the design of concrete structures. Nonlinear time history analyses are also performed to provide a benchmark for comparison. Results show that the new method can predict shear and bending moment in all members at once with ease. Therefore, this new simplified method can effectively be used to predict seismic forces in elements not considered part of the SFRS.

Application of Damper in the Seismic Engineering

2013 ◽  
Vol 391 ◽  
pp. 301-304
Author(s):  
Teng Fei Zhong ◽  
Yu Bai ◽  
Ya Juan Sun
Keyword(s):  
Energy Dissipation ◽  
Time History ◽  
Reference Value ◽  
Seismic Effect ◽  
Parameter Method ◽  
Stiffness Parameter ◽  
Seismic Engineering ◽  
History Of ◽  
Nonlinear Time History ◽  
Simplified Modeling

The article describes the theory and application of energy dissipation technology. Puts forward the simplified modeling and optimization of damper stiffness parameter method .Through nonlinear time history of the structure show its obvious seismic effect. Prove that the method has certain reference value of the energy dissipation design.

Optimization Design of Large Span Cable-Stayed Bridge in High Seismic Risk Zone

2013 ◽  
Vol 353-356 ◽  
pp. 2015-2019
Author(s):  
Zhi Hua Xiong ◽  
Yun Cheng Feng ◽  
Song Lin Song ◽  
Jiang Bo Wang
Keyword(s):  
Optimization Design ◽  
Time History ◽  
Nonlinear Time History Analysis ◽  
Seismic Safety ◽  
Seismic Demands ◽  
Large Span ◽  
Cable Stayed Bridge ◽  
History Analysis ◽  
Ductile Steel ◽  
Nonlinear Time History

To ensure seismic safety of a large span cable-stayed bridge, two alternative pylon shapes and section types were studied. Nonlinear time history analysis was performed in the context. It is found that the A-shaped pylon is much stiffener than the H-shaped pylon in terms of deformation. The steel A-shaped pylon can significantly reduce the seismic demands of the key member including tower drift and moment. A ductile steel link between towers is proposed for the optimization of design in the paper. The A-shaped reinforced concrete tower with ductile steel link was proved to be a relatively balanced plan considering engineering, aesthetic and economic factors.

Non-Linear Step-by-Step Seismic Response and the Push-Over Analysis Comparison of a Reinforced Concrete of Ductile Frames 15 Level Building

2008 ◽  
Vol 385-387 ◽  
pp. 229-232
Author(s):  
Jorge A. Avila ◽  
Eduardo Martínez
Keyword(s):  
Lateral Displacement ◽  
Time History ◽  
Seismic Zone ◽  
Lateral Loads ◽  
Base Shear ◽  
Non Linear ◽  
Story Drift ◽  
Lateral Displacements ◽  
Group B ◽  
Level Building

Based on a ductile frames 15 level building, a non-linear analysis with increased monotonically lateral loads (Push-Over) was made in order to determine its collapse and its principal responses were compared against the elastic and inelastic time-history seismic responses determined with the SCT-EW-85 record. The seismic-resistance design and faced to gravitational loads was made according to the Complementary Technical Norms of Concrete Structures Design (NTC-Concrete) and the NTC-Seismic of the Mexico City Code (RDF-04), satisfying the limit service states (relative lateral displacement between story height maximum relations, story drifts ≤ 0.012) and failure (seismic behavior factor, Q= 3). The compressible (soft) seismic zone IIIb and the office use type (group B) were considered. The non-linear responses were determined with nominal and over-resistance effects. The comparison were made with base shear force–roof lateral displacement relations, global distribution of plastic hinges, failure mechanics tendency, lateral displacements and story drift and its distribution along the height of the building, local and global ductility demands, etc. For the non-linear static analysis with increased monotonically lateral loads, it was important to select the type of lateral forces distribution.

Sign in / Sign up

Export Citation Format

Share Document