scholarly journals Evaluation of Mechanical Properties of Micro-Titanium and CNT Reinforced Copper Based MMC

2021 ◽  
pp. 81-104
Author(s):  
Dr. Ranjith V ◽  
Dr. H K Shivanand2 ◽  
Dr. Tukaram Jadhav3 ◽  
Verma R4 ◽  
Puneeth P
Keyword(s):  
Mechanical Properties ◽  
Performance Studies ◽  
Metal Matrix ◽  
Stir Casting ◽  
Vital Role ◽  
New Combination ◽  
Matrix Composites ◽  
Power Sector ◽  
Casting Technique ◽  
Effective Reinforcement

Copper based composites plays a vital role in the field of marine, aerospace, automobile and power sector for making of components like electrical sliding contacts, gears, bearings, bushes, brakes and clutches etc. Even though promising reinforcements are available for the composites, always researchers search for the new combination of matrix and reinforcement for tailored properties and cost effectiveness. CNT is one of the effective reinforcement used in the metal matrix composites by various researches because of its excellent properties. The present work is focused on the preparation of copper/CNTs/Micro-Titanium composite through stir casting technique performance studies of the composite are made on the mechanical properties. The composite prepared with reinforcement such as CNTs and Micro-Titanium of 0.5, 1, 1.5 % and 1, 3 & 5wt. % were studied. The Tensile strength, Compression strength, Hardness was found out via experimentation.

An Investigation of Mechanical Properties on Aluminium 6061 Reinforced with Silicon Carbide - Metal Matrix Composites

2015 ◽  
Vol 787 ◽  
pp. 568-572 ◽  
Author(s):  
A. Radha ◽  
K.R. Vijayakumar
Keyword(s):  
Mechanical Properties ◽  
Silicon Carbide ◽  
Metal Matrix ◽  
Charpy Impact ◽  
Vortex Method ◽  
Weight Fraction ◽  
Stir Casting ◽  
Matrix Composites ◽  
Casting Technique ◽  
High Fatigue

Composite materials like Aluminium metal matrix composite is playing a very important role in manufacturing industries e.g. automobile and aerospace industries, due to their superior properties such as light weight, low density, high specific modulus, high fatigue strength etc., In this study Aluminium(Al 6061) is reinforced with Silicon Carbide particles and fabricated by Stir Casting Technique (vortex method). The MMC rectangular bars (samples) are prepared with Al6061 and SiC (28 µ size) as the reinforced particles by weight fraction from 0%, 5%, 10%, and 15% of SiC. The microstructure analysis and Mechanical properties like Tensile Strength, Vickers Hardness and Charpy Impact Strength were investigated on prepared specimens. It is observed that the properties are increased with increasing of reinforced specimens by weight fraction.

Characterization and mechanical response of novel Al-(Mg–TiFe–SiC) metal matrix composites developed by stir casting technique

2019 ◽  
Vol 53 (28-30) ◽  
pp. 3929-3938 ◽  
Author(s):  
Samuel O Akinwamide ◽  
Serge M Lemika ◽  
Babatunde A Obadele ◽  
Ojo J Akinribide ◽  
Bolanle T Abe ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Silicon Carbide ◽  
Metal Matrix ◽  
Mechanical Response ◽  
Frictional Coefficient ◽  
Stir Casting ◽  
Matrix Composites ◽  
Tribological Behaviour ◽  
Casting Technique ◽  
Electron Microscopes

This study was conducted to investigate the synthesis, characterization and mechanical properties of aluminium reinforced with ferrotitanium and silicon carbide via stir casting technique. Microstructures of as-cast samples were analysed using optical and scanning electron microscopes equipped with energy-dispersive X-ray spectroscopy. The mechanical properties in terms of hardness, tensile, tribological behaviour and fracture were assessed. Results showed that the homogeneous dispersion of reinforcement was within the metal matrix composite. Tribological study revealed a decrease in frictional coefficient of the composites with lowest frictional coefficient observed in composite with addition of silicon carbide as reinforcement. Morphology of fractured surface displayed a reduction in the size of dimples formed in reinforced aluminium composites when compared with larger dimple sizes observed in as-cast aluminium alloy.

Microstructure and Mechanical Behavior of Nanoparticles Reinforced Metal Matrix Composites – A Review

2014 ◽  
Vol 592-594 ◽  
pp. 939-944 ◽  
Author(s):  
S. Santhosh Kumar ◽  
Somashekhar S. Hiremath
Keyword(s):  
Mechanical Properties ◽  
Metal Matrix Composites ◽  
Metal Matrix ◽  
High Performance ◽  
Physical And Mechanical Properties ◽  
Stir Casting ◽  
Matrix Composites ◽  
Casting Technique ◽  
Effect Of Particle Size ◽  
Properties Of Composites

Micro sized particles such as SiC, Al2O3and diamond particles reinforced with metal matrix composites are most commonly used in high performance applications like military, automotive and aerospace industries. Nowadays nano sized particles are replacing the micro sized particles because of their improved physical and mechanical properties. This paper reviews the stir processing method, mechanical properties, effect of particle size on properties of composites and structure of the metal matrix composites reinforced with nanoparticles. Among the variety of liquid metallurgy techniques processes available for preparing metal matrix composites, stir casting technique is generally accepted route and currently practised commercially because of its simplicity flexibility and Uniform distribution.

scholarly journals Machinability study of Al-TiC metal matrix composite

2018 ◽  
Vol 144 ◽  
pp. 03001 ◽  
Author(s):  
P. N. Siddappa ◽  
B. P. Shivakumar ◽  
K. B. Yogesha ◽  
M. Mruthunjaya ◽  
M. B. Hanamantraygouda
Keyword(s):  
Mechanical Properties ◽  
Feed Rate ◽  
Metal Matrix ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Stir Casting ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Matrix Composites ◽  
Casting Technique

Aluminum Metal Matrix Composites have emerged as an advanced class of structural materials have a combination of different, superior properties compared to an unreinforced matrix, which can result in a number of service benefits such as increased strength, higher elastic moduli, higher service temperature, low CTE, improved wear resistance, high toughness, etc. The excellent mechanical properties of these materials together with weight saving makes them very attractive for a variety of engineering applications in aerospace, automotive, electronic industries, etc. Hence, these materials provide as alternative substitutes for conventional engineering materials when specific mechanical properties necessary for required applications. In this work an attempt is made to study the machining parameters of Al6061/TiC MMC. The composite is developed by reinforcing TiC particles in varying proportions of 3, 6, 9 and 12 % weight fractions to the Al6061 matric alloy through stir casting technique. Cutting forces were measured by varying cutting speed and feed rate with constant depth of cut for different % weight fractions. The results showed that the cutting force increases with the increase of feed rate and decreases with the increase of cutting speed for all the weight fractions. Cutting parameters were optimized using Taguchi technique.

scholarly journals Properties of AlSi9Cu3 metal matrix micro and nano composites produced via stir casting

2018 ◽  
Vol 16 (1) ◽  
pp. 726-731 ◽  
Author(s):  
Tennur Gülşen Ünal ◽  
Ege Anıl Diler
Keyword(s):  
Mechanical Properties ◽  
Metal Matrix ◽  
Weight Fraction ◽  
Stir Casting ◽  
Mechanical Tests ◽  
Matrix Composites ◽  
Casting Method ◽  
Porosity Formation ◽  
Three Point Bending ◽  
Hardness Values

AbstractThe effects of micro and nano sized reinforcement particles on microstructure and mechanical properties of aluminium alloy-based metal matrix composites were investigated in this study. AlSi9Cu3 alloy was reinforced with micro and nano sized ceramic reinforcement particles at different weight fractions by using a stir casting method. The mechanical tests (hardness, three point bending) were performed to determine the mechanical properties of AlSi9Cu3 alloy-based microcomposites (AMMCs) and nanocomposites (AMMNCs). The experimental results have shown that the size and weight fraction of reinforcement particles have a strong influence on the microstructure and the mechanical properties of AlSi9Cu3 alloy-based microcomposites and nanocomposites. The relative densities of all AMMC and AMMNC samples are lower than unreinforced AlSi9Cu3 alloy due to porosity formation with the increase of weight fraction of reinforcement particles. As weight fraction increases, hardness values of AMMCs and AMMNCs increase. Maximum flexural strength can be obtained at 3.5wt.% for the AMMC sample with microsized Al2O3 particles and at 2wt.% for the AMMNC sample with nano-sized Al2O3 particles. After the weight fractions exceed these values, flexural strengths of both AMMCs and AMMNCs decrease due to clustering of Al2O3 particles.

Production of Al Metal Matrix Composites by the Stir-Casting Method

2013 ◽  
Vol 592-593 ◽  
pp. 614-617 ◽  
Author(s):  
Konstantinos Anthymidis ◽  
Kostas David ◽  
Pavlos Agrianidis ◽  
Afroditi Trakali
Keyword(s):  
Mechanical Properties ◽  
Metal Matrix Composites ◽  
Automobile Industry ◽  
Metal Matrix ◽  
Aluminum Matrix ◽  
Stir Casting ◽  
Aluminum Matrix Composites ◽  
Matrix Composites ◽  
Casting Method ◽  
Alloy Matrix

It is well known that the addition of ceramic phases in an alloy e.g. aluminum, in form of fibers or particles influences its mechanical properties. This leads to a new generation of materials, which are called metal matrix composites (MMCs). They have found a lot of application during the last twenty-five years due to their low density, high strength and toughness, good fatigue and wear resistance. Aluminum matrix composites reinforced by ceramic particles are well known for their good thermophysical and mechanical properties. As a result, during the last years, there has been a considerable interest in using aluminum metal matrix composites in the automobile industry. Automobile industry use aluminum alloy matrix composites reinforced with SiC or Al2O3 particles for the production of pistons, brake rotors, calipers and liners. However, no reference could be cited in the international literature concerning aluminum reinforced with TiB particles and Fe and Cr, although these composites are very promising for improving the mechanical properties of this metal without significantly alter its corrosion behavior. Several processing techniques have been developed for the production of reinforced aluminum alloys. This paper is concerned with the study of TiB, Fe and Cr reinforced aluminum produced by the stir-casting method.

Mechanical properties and fracture mechanism of ZA-27/TiO2 particulate metal matrix composites

2003 ◽  
Vol 217 (3) ◽  
pp. 201-206 ◽  
Author(s):  
K H W Seah ◽  
S C Sharma ◽  
M Krishna
Keyword(s):  
Mechanical Properties ◽  
Titanium Dioxide ◽  
Fracture Mechanism ◽  
Matrix Alloy ◽  
Stir Casting ◽  
Primary Objective ◽  
Matrix Composites ◽  
Casting Technique ◽  
Titanium Dioxide Particle ◽  
The Matrix

The mechanical properties and the fracture mechanism of composites consisting of ZA-27 alloy reinforced with titanium dioxide particles were investigated with the primary objective of understanding the influence of the particulate reinforcement on the mechanical behaviour of the ZA-27 alloy. The titanium dioxide particle content in the composites ranged from 0 to 6 per cent, in steps of 2 wt %. The composites were fabricated by the stir casting technique in which the reinforcement particles were dispersed in the vortex created in the molten matrix alloy. The study revealed improvements in Young's modulus, ultimate tensile strength (UTS), compressive strength, yield strength and hardness of the composites as the titanium dioxide content was increased, but at the expense of ductility and impact strength. The fracture behaviour of the composite was also significantly influenced by the presence of titanium dioxide particles. Eventual fracture was a result of crack propagation through the matrix as well as through the reinforcing particles. Scanning electron microscopy and fractography analyses were carried out to provide suitable explanations for the observed phenomena.

Sign in / Sign up

Export Citation Format

Share Document