scholarly journals Optically resonant structures for the enhancement of polycrystalline PbSe photoconductors

2018 ◽  
Author(s):  
◽  
Justin Stewart Grayer
Keyword(s):  
Surface Plasmon ◽  
Room Temperature ◽  
Operating Temperature ◽  
Signal To Noise Ratio ◽  
Electromagnetic Spectrum ◽  
Test Results ◽  
Resonant Structures ◽  
Atmospheric Window ◽  
Back Reflector ◽  
Reference Detector

The mid-wave infrared (MWIR) regime of the electromagnetic spectrum is attractive for long-range imaging systems due to the atmospheric window between 3 and 5 [mu]m. Due to ambient thermal background, it is often necessary to operate sensor systems below room temperature to achieve an adequate signal-to-noise ratio (SNR). This cooling requirement adds size, weight, and complexity to systems in which these parameters are at a premium. In this work I investigated two methods for optically enhancing the absorptive properties of lead selenide (PbSe) photoconductive films to increase the operating temperature up to 290 K, thereby mitigating system cooling requirements. By employing surface plasmon resonant (SPR) and embedded reflective structures, we were able to demonstrate enhanced responsivity and raise the operating temperature to room-temperature. Sensitivity was observed to increase by a factor of three for SPR enhanced detectors, and up to two-times at room temperature in detectors with an embedded Pt back reflector. Moreover, PbSe detectors with SPR discs operating at room temperature were observed to have responsivity comparable to reference detectors at 230 K. Photoconductors with the embedded Pt back reflector had a performance at room temperature that was similar to the reference detector at 250 K. Herein, I discuss my design process, as well as the fabrication of these resonant structures. Also discussed are the measurement and test results I obtained from surface plasmon and embedded reflector enhanced PbSe detectors. In this dissertation, I present results that demonstrate the viability of SPR and interference structures as mechanisms for increasing the operating temperature of PbSe MWIR photodetectors up to 290 K

scholarly journals Effect of Substrate Plate Heating on the Microstructure and Properties of Selective Laser Melted Al-20Si-5Fe-3Cu-1Mg Alloy

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 330
Author(s):  
Pan Ma ◽  
Pengcheng Ji ◽  
Yandong Jia ◽  
Xuerong Shi ◽  
Zhishui Yu ◽  
...  
Keyword(s):  
Room Temperature ◽  
Internal Stresses ◽  
Test Results ◽  
Laser Melting ◽  
Microstructure And Properties ◽  
Uniform Microstructure ◽  
Heat Treated ◽  
Fine Microstructure ◽  
Plate Heating ◽  
Substrate Plate

The Al-20Si-5Fe-3Cu-1Mg alloy was fabricated using selective laser melting (SLM). The microstructure and properties of the as-prepared SLM, post-treated SLM, and SLM with substrate plate heating are studied. The as-prepared SLM sample shows a non-uniform microstructure with four different phases: fcc-αAl, eutectic Al-Si, Al2MgSi, and δ-Al4FeSi2. With thermal treatment, the phases become coarser and the δ-Al4FeSi2 phase transforms partially to β-Al5FeSi. The sample produced with SLM substrate plate heating shows a relatively uniform microstructure without a distinct difference between hatch overlaps and track cores. Room temperature compression test results show that an as-prepared SLM sample reaches a maximum strength (862 MPa) compared to the heat-treated (524 MPa) and substrate plate heated samples (474 MPa) due to the presence of fine microstructure and the internal stresses. The reduction in strength of the sample produced with substrate plate heating is due to the coarsening of the microstructure, but the plastic deformation shows an improvement (20%). The present observations suggest that substrate plate heating can be effectively employed not only to minimize the internal stresses (by impacting the cooling rate of the process) but can also be used to modulate the mechanical properties in a controlled fashion.

scholarly journals Plasmonic semiconductor nanogroove array enhanced broad spectral band millimetre and terahertz wave detection

2021 ◽  
Vol 10 (1) ◽  
Author(s):  
Jinchao Tong ◽  
Fei Suo ◽  
Tianning Zhang ◽  
Zhiming Huang ◽  
Junhao Chu ◽  
...  
Keyword(s):  
Surface Plasmon ◽  
High Performance ◽  
Room Temperature ◽  
Spectral Band ◽  
High Capacity ◽  
Terahertz Wave ◽  
Semiconductor Surface ◽  
Wide Range ◽  
Low Sensitivity ◽  
Air Interfaces

AbstractHigh-performance uncooled millimetre and terahertz wave detectors are required as a building block for a wide range of applications. The state-of-the-art technologies, however, are plagued by low sensitivity, narrow spectral bandwidth, and complicated architecture. Here, we report semiconductor surface plasmon enhanced high-performance broadband millimetre and terahertz wave detectors which are based on nanogroove InSb array epitaxially grown on GaAs substrate for room temperature operation. By making a nanogroove array in the grown InSb layer, strong millimetre and terahertz wave surface plasmon polaritons can be generated at the InSb–air interfaces, which results in significant improvement in detecting performance. A noise equivalent power (NEP) of 2.2 × 10−14 W Hz−1/2 or a detectivity (D*) of 2.7 × 1012 cm Hz1/2 W−1 at 1.75 mm (0.171 THz) is achieved at room temperature. By lowering the temperature to the thermoelectric cooling available 200 K, the corresponding NEP and D* of the nanogroove device can be improved to 3.8 × 10−15 W Hz−1/2 and 1.6 × 1013 cm Hz1/2 W−1, respectively. In addition, such a single device can perform broad spectral band detection from 0.9 mm (0.330 THz) to 9.4 mm (0.032 THz). Fast responses of 3.5 µs and 780 ns are achieved at room temperature and 200 K, respectively. Such high-performance millimetre and terahertz wave photodetectors are useful for wide applications such as high capacity communications, walk-through security, biological diagnosis, spectroscopy, and remote sensing. In addition, the integration of plasmonic semiconductor nanostructures paves a way for realizing high performance and multifunctional long-wavelength optoelectrical devices.

scholarly journals Ab initiostructure determination of nanocrystals of organic pharmaceutical compounds by electron diffraction at room temperature using a Timepix quantum area direct electron detector

2016 ◽  
Vol 72 (2) ◽  
pp. 236-242 ◽  
Author(s):  
E. van Genderen ◽  
M. T. B. Clabbers ◽  
P. P. Das ◽  
A. Stewart ◽  
I. Nederlof ◽  
...  
Keyword(s):  
Electron Diffraction ◽  
Room Temperature ◽  
Dynamic Range ◽  
Signal To Noise Ratio ◽  
Three Dimensional ◽  
Direct Methods ◽  
Liquid Nitrogen Temperature ◽  
High Dynamic Range ◽  
Electron Diffraction Data ◽  
High Signal

Until recently, structure determination by transmission electron microscopy of beam-sensitive three-dimensional nanocrystals required electron diffraction tomography data collection at liquid-nitrogen temperature, in order to reduce radiation damage. Here it is shown that the novel Timepix detector combines a high dynamic range with a very high signal-to-noise ratio and single-electron sensitivity, enablingab initiophasing of beam-sensitive organic compounds. Low-dose electron diffraction data (∼0.013 e− Å−2 s−1) were collected at room temperature with the rotation method. It was ascertained that the data were of sufficient quality for structure solution using direct methods using software developed for X-ray crystallography (XDS,SHELX) and for electron crystallography (ADT3D/PETS,SIR2014).

scholarly journals Cellulose and Vanadium Plasmonic Sensor to Measure Ni2+ Ions

2021 ◽  
Vol 11 (7) ◽  
pp. 2963
Author(s):  
Nur Alia Sheh Omar ◽  
Yap Wing Fen ◽  
Irmawati Ramli ◽  
Umi Zulaikha Mohd Azmi ◽  
Hazwani Suhaila Hashim ◽  
...  
Keyword(s):  
Thin Film ◽  
Surface Plasmon Resonance ◽  
Surface Plasmon ◽  
Plasmon Resonance ◽  
Signal To Noise Ratio ◽  
Affinity Constant ◽  
Detection Accuracy ◽  
Plasmonic Sensor ◽  
Spr Sensor ◽  
Resonance Sensor

A novel vanadium–cellulose composite thin film-based on angular interrogation surface plasmon resonance (SPR) sensor for ppb-level detection of Ni(II) ion was developed. Experimental results show that the sensor has a linear response to the Ni(II) ion concentrations in the range of 2–50 ppb with a determination coefficient (R2) of 0.9910. This SPR sensor can attain a maximum sensitivity (0.068° ppb−1), binding affinity constant (1.819 × 106 M−1), detection accuracy (0.3034 degree−1), and signal-to-noise-ratio (0.0276) for Ni(II) ion detection. The optical properties of thin-film targeting Ni(II) ions in different concentrations were obtained by fitting the SPR reflectance curves using the WinSpall program. All in all, the proposed Au/MPA/V–CNCs–CTA thin-film-based surface plasmon resonance sensor exhibits better sensing performance than the previous film-based sensor and demonstrates a wide and promising technology candidate for environmental monitoring applications in the future.

Cryogenic Interlaminar Properties of PBO Fiber/Epoxy Composites

2011 ◽  
Vol 391-392 ◽  
pp. 1445-1449
Author(s):  
Chun Hua Zhang ◽  
Shi Lin Luan ◽  
Xiu Song Qian ◽  
Bao Hua Sun ◽  
Wen Sheng Zhang
Keyword(s):  
Liquid Nitrogen ◽  
Room Temperature ◽  
Liquid Nitrogen Temperature ◽  
Epoxy Composites ◽  
Bending Test ◽  
Test Results ◽  
Sem Images ◽  
Three Point Bending ◽  
Pbo Fiber ◽  
Interlaminar Shear

The influences of low temperature on the interlaminar properties for PBO fiber/epoxy composites have been studied at liquid nitrogen temperature (77 K) in terms of three point bending test. Results showed that the interlaminar shear strength at 77 K were significantly higher than those at room temperature (RT). For the analysis of the test results, the tensile behaviors of epoxy resin at both room temperature and liquid nitrogen temperature were investigated. The interface between fiber and matrix was observed using SEM images.

High performance shape memory effect in nitinol wire for actuators with increased operating temperature range

2014 ◽  
Vol 07 (05) ◽  
pp. 1450063 ◽  
Author(s):  
Riccardo Casati ◽  
Carlo Alberto Biffi ◽  
Maurizio Vedani ◽  
Ausonio Tuissi
Keyword(s):  
Shape Memory ◽  
Shape Memory Effect ◽  
Memory Effect ◽  
High Performance ◽  
Room Temperature ◽  
Operating Temperature ◽  
Niti Wire ◽  
Shape Memory Actuators ◽  
Nitinol Wire ◽  
Operating Temperature Range

In this research, the high performance shape memory effect (HP-SME) is experimented on a shape memory NiTi wire, with austenite finish temperature higher than room temperature. The HP-SME consists in the thermal cycling of stress induced martensite and it allows achieving mechanical work higher than that produced by conventional shape memory actuators based on the heating/cooling of detwinned martensite. The Nitinol wire was able to recover about 5.5% of deformation under a stress of 600 MPa and to withstand about 5000 cycles before failure. HP-SME path increased the operating temperature of the shape memory actuator wire. Functioning temperatures higher than 100°C was reached.

scholarly journals Magnetic properties of cobalt microwires measured by piezoresistive cantilever magnetometry

2014 ◽  
Vol 1 (1) ◽  
Author(s):  
G. Tosolini ◽  
J. M. Michalik ◽  
R. Córdoba ◽  
J. M. de Teresa ◽  
F. Pérez-Murano ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Room Temperature ◽  
Signal To Noise Ratio ◽  
Static Deflection ◽  
Magnetic Structures ◽  
Dual Beam ◽  
Piezoresistive Cantilevers ◽  
Good Signal ◽  
The Magnetic Field

AbstractWe present the magnetic characterization of cobalt wires grown by focused electron beam-induced deposition (FEBID) and studied using static piezoresistive cantilever magnetometry. We have used previously developed high force sensitive submicron-thick silicon piezoresistive cantilevers. High quality polycrystalline cobalt microwires have been grown by FEBID onto the free end of the cantilevers using dual beam equipment. In the presence of an external magnetic field, the magnetic cobalt wires become magnetized, which leads to the magnetic field dependent static deflection of the cantilevers. We show that the piezoresistive signal from the cantilevers, corresponding to a maximum force of about 1 nN, can be measured as a function of the applied magnetic field with a good signal to noise ratio at room temperature. The results highlight the flexibility of the FEBID technique for the growth of magnetic structures on specific substrates, in this case piezoresistive cantilevers.

Additional Engine Testing of an Advanced Alloy for Microturbine Primary Surface Recuperators

2006 ◽  
Author(s):  
Wendy J. Matthews
Keyword(s):  
Operating Temperature ◽  
Engine Test ◽  
Test Results ◽  
Preliminary Estimate ◽  
Parabolic Model ◽  
Scale Growth ◽  
Temperature Oxide ◽  
Model Engine ◽  
Engine Testing ◽  
Elemental Depletion

HAYNES ® alloy HR-120 ® is being evaluated as a replacement for type 347 stainless steel for use in Microturbine Primary Surface Recuperators. The material has been characterized after being subjected to both steady-state and cyclic engine exposure in a Capstone C60 MicroTurbine™ operating at 100°F above the normal operating temperature. Oxide scale growth and elemental depletion has been analyzed and documented after 1,800 and 2,500 hours of exposure. A preliminary estimate of the remaining usable oxidation life has been made using a simplified parabolic model. Engine test results indicate that HR-120 has improved oxidation resistance and elemental stability.

Sign in / Sign up

Export Citation Format

Share Document