Design and performance analysis of a novel PM assisted synchronous reluctance machine

2021 ◽  
pp. 1-10
Author(s):  
Shaopeng Wang ◽  
Jinguang Ma ◽  
Chengcheng Liu ◽  
Youhua Wang ◽  
Gang Lei ◽  
...  
Keyword(s):  
Mechanical Performance ◽  
Rolling Direction ◽  
Silicon Steel ◽  
Design Parameters ◽  
Maximum Speed ◽  
The Novel ◽  
The Finite Element Method ◽  
Reluctance Machine ◽  
And Performance ◽  
Two Machines

This paper proposes a novel permanent magnet assisted synchronous reluctance (PMAREL) machine, the main structure of this machine is quite similar to that of traditional PMAREL machine, and the main difference is that the grain-oriented silicon steel is used to replace some part of the stator teeth. The rolling direction of the grain-oriented silicon steel is along the radial direction of the machine, thus the advantage of higher permeability and higher kneel point in this material can be used to release the flux saturation problem of the traditional non-grain-oriented steel used in the PMAREL machine when the applied current density is high. Firstly, the structure of both proposed novel and traditional PMAREL machines are optimized and the design parameters are determined. Secondly the electromagnetic and mechanical performance are compared in these two machines which includes the demagnetization analysis, mechanical stress analysis when the rotor at the maximum speed, torque ability, efficiency by using the finite element method (FEM). It can be seen that the problem of stator teeth saturation in the novel PMAREL has been alleviated, and compared with the traditional PMAREL machine, the novel PMAREL has higher efficiency, wider speed range and 7% higher torque ability.

scholarly journals Design Optimization and Performance Analysis of the Pneumatic DTH Hammer with Self-Propelled Round Bit

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Kun Bo ◽  
Siyuan Sun ◽  
Yong Hu ◽  
Maosen Wang
Keyword(s):  
Oil And Gas ◽  
Vertical Section ◽  
Dynamics Simulation ◽  
Chamber Pressure ◽  
Design Parameters ◽  
The Novel ◽  
Directional Drilling ◽  
Pressure Impact ◽  
Working Principle ◽  
And Performance

Although pneumatic down-the-hole (DTH) hammers have good performance of high penetration rate and minimal deviation tendency in the vertical section of oil and gas wells, they have not been successfully used in directional drilling due to drill tool wear and wellbore disturbance. Herein, we developed a novel type of pneumatic DTH hammer with a self-propelled round bit to overcome the technical difficulties of directional drilling. Nonlinear dynamic modeling developed by the authors was used to analyze the working principle and performance of the novel DTH hammer. The kinematics and dynamics simulation of this hammer were carried out using MATLAB language, and the motion law of the piston was revealed. The performance of the novel hammer was numerically simulated and evaluated by considering fluctuations of the front and rear chamber pressure, impact energy, acceleration, and frequency. The results show that our novel DTH hammer’s working principle is feasible and has an adequate structural design. The simulation results demonstrate reasonable design parameters. Compared to the numerical results for conventional DTH hammers, the velocity and acceleration of the piston of the novel hammer changed smoothly. The frequency was slightly higher than that of conventional hammers, while other parameters were nearly equal. The novel DTH hammer can be used in directional drilling, trenchless drilling, and seabed sampling drilling.

Mathematic Analysis and Performance Simulation for Exhaust Muffler Based on Transmission Loss

2014 ◽  
Vol 651-653 ◽  
pp. 972-975
Author(s):  
Xiao Dong Li ◽  
Xin Tan Ma
Keyword(s):  
Transmission Loss ◽  
Expansion Ratio ◽  
Design Parameters ◽  
Analysis Method ◽  
Frequency Bandwidth ◽  
The Finite Element Method ◽  
Expansion Chamber ◽  
Performance Simulation ◽  
Chamber Length ◽  
And Performance

Transmission loss is an important noise reduction parameter of exhaust muffler. Based on the finite element method, transmission loss is calculated, and the influential effect of the fluid is considered in this paper. Through calculation of transmission loss of the single expendable muffler and composite muffler, the results show that expansion ratio affects amplitude of transmission loss, and expansion chamber length affects the attenuation frequency bandwidth. The analysis method and conclusions are instructive to the design parameters of exhaust muffler.

Design and Optimization of Thermomechanical Actuator via Contour Shaping

2005 ◽  
Author(s):  
Shih-Chi Chen ◽  
Martin L. Culpepper
Keyword(s):  
Mechanical Performance ◽  
Mechanical Energy ◽  
Thermal Strain ◽  
Design Tool ◽  
Design Parameters ◽  
Axial Stiffness ◽  
Element Analysis ◽  
Design Assessment ◽  
Design And Optimization ◽  
And Performance

In this paper we disclose how to contour the beams of micro-scale thermomechanical actuators (TMAs) in order to enhance the actuator’s thermal and mechanical performance. In this approach, we vary the cross section of the driving Joule heated beams over the length of the beam. Using this approach, (1) the stored mechanical energy and axial stiffness of beam may be modified to achieve an optimized force-displacement relationship, (2) the maximum achievable thermal strain of a driving beam may be increased by 29%, (3) actuator stroke may be increased by a factor of 3 or more, (4) identical force or displacement characteristics may be achieved with 90% reduction in power. This paper presents the theory and models used to predict the thermal and mechanical behavior of the actuator. The theory and models were used to create a deterministic link between the actuator’s design parameters and the actuator’s performance characteristics. The theory and models were combined within a design tool that shows less than 5% error from non-linear Finite Element Analysis simulations. The design tool has been used to generate plots that enable designers to (1) understand the qualitative relationships between design parameters and performance and (2) select first-pass design parameters. The theory was used to create a design tool, posted at http://psdam.mit.edu, that may be used to perform qualitative design assessment and optimization.

Design and Simulation of Piezoelectric Micro-Cantilever Ultrasonic Transducers for Audio Directional Loudspeakers

2008 ◽  
Author(s):  
Teng Ma ◽  
Chenguang Cai ◽  
Limei Xu ◽  
Leon Xu ◽  
Xia Wang ◽  
...  
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Mobile Communication ◽  
Mechanical Performance ◽  
Micro Electro Mechanical System ◽  
Ultrasonic Transducers ◽  
Design Parameters ◽  
The Finite Element Method ◽  
Communication Devices ◽  
Micro Cantilever

This paper presents a piezoelectric multilayered microcantilever structure as a micro-electro-mechanical system (MEMS) transducer. The proposed micro-transducer is designed for novel audio directional loudspeaker for mobile communication devices. To obtain optimum design parameters and predict the cantilever performance before actual fabrication, the mechanical and electro-mechanical performance was simulated by the finite element method and further validated with theoretical calculation. Finally the fabrication process steps are proposed.

scholarly journals Design, Analysis, and Experiment on a Novel Stick-Slip Piezoelectric Actuator with a Lever Mechanism

Micromachines ◽  
2019 ◽  
Vol 10 (12) ◽  
pp. 863 ◽  
Author(s):  
Weiqing Huang ◽  
Mengxin Sun
Keyword(s):  
Piezoelectric Actuator ◽  
Simple Structure ◽  
Fast Response ◽  
Displacement Sensor ◽  
Design Parameters ◽  
The Finite Element Method ◽  
Stick Slip ◽  
Lever Mechanism ◽  
Series Of Experiments ◽  
Stator Design

A piezoelectric actuator using a lever mechanism is designed, fabricated, and tested with the aim of accomplishing long-travel precision linear driving based on the stick-slip principle. The proposed actuator mainly consists of a stator, an adjustment mechanism, a preload mechanism, a base, and a linear guide. The stator design, comprising a piezoelectric stack and a lever mechanism with a long hinge used to increase the displacement of the driving foot, is described. A simplified model of the stator is created. Its design parameters are determined by an analytical model and confirmed using the finite element method. In a series of experiments, a laser displacement sensor is employed to measure the displacement responses of the actuator under the application of different driving signals. The experiment results demonstrate that the velocity of the actuator rises from 0.05 mm/s to 1.8 mm/s with the frequency increasing from 30 Hz to 150 Hz and the voltage increasing from 30 V to 150 V. It is shown that the minimum step distance of the actuator is 0.875 μm. The proposed actuator features large stroke, a simple structure, fast response, and high resolution.

scholarly journals A modular design method based on TRIZ and AD and its application to cutter changing robot

2021 ◽  
Vol 13 (7) ◽  
pp. 168781402110343
Author(s):  
Mei Yang ◽  
Yimin Xia ◽  
Lianhui Jia ◽  
Dujuan Wang ◽  
Zhiyong Ji
Keyword(s):  
Modular Design ◽  
Design Method ◽  
Idea Generation ◽  
Design Parameters ◽  
Problem Analysis ◽  
Concept Design ◽  
Functional Requirements ◽  
Shield Tunneling ◽  
Structural Hierarchy ◽  
And Performance

Modular design, Axiomatic design (AD) and Theory of inventive problem solving (TRIZ) have been increasingly popularized in concept design of modern mechanical product. Each method has their own advantages and drawbacks. The benefit of modular design is reducing the product design period, and AD has the capability of problem analysis, while TRIZ’s expertise is innovative idea generation. According to the complementarity of these three approaches, an innovative and systematic methodology is proposed to design big complex mechanical system. Firstly, the module partition is executed based on scenario decomposition. Then, the behavior attributes of modules are listed to find the design contradiction, including motion form, spatial constraints, and performance requirements. TRIZ tools are employed to deal with the contradictions between behavior attributes. The decomposition and mapping of functional requirements and design parameters are carried out to construct the structural hierarchy of each module. Then, modules are integrated considering the connections between each other. Finally, the operation steps in application scenario are designed in temporal and spatial dimensions. Design of cutter changing robot for shield tunneling machine is taken as an example to validate the feasibility and effectiveness of the proposed method.

Damping characteristics of a magneto-rheological damper with dual independent controllable ducts

2021 ◽  
pp. 1045389X2110188
Author(s):  
Jianqiang Yu ◽  
Xiaomin Dong ◽  
Tao Wang ◽  
Zhengmu Zhou ◽  
Yaqin Zhou
Keyword(s):  
Dynamic Range ◽  
Fluid Flows ◽  
Mr Damper ◽  
Viscous Damping ◽  
The Novel ◽  
The Finite Element Method ◽  
Damping Force ◽  
Damping Characteristics ◽  
Magneto Rheological ◽  
The Mathematical Model

This paper presents the damping characteristics of a linear magneto-rheological (MR) damper with dual controllable ducts based on numerical and experimental analysis. The novel MR damper consisting of a dual-rod cylinder system and a MR valve is used to reduce the influences of viscous damping force and improve dynamic range. Driven by the dual-rod cylinder system, MR fluid flows in the MR valve. The pressure drop of the MR valve with dual independent controllable ducts can be controlled by tuning the current of two independent coils. Based on the mathematical model and the finite element method, the damping characteristics of the MR damper is simulated. A prototype is designed and tested on MTS machine to evaluate its damping characteristics. The results show that the working states and damping force of the MR damper can be controlled by the two independent coils.

scholarly journals Does Hyperoxia Restrict Pyrenean Rock Lizards Iberolacerta bonnali to High Elevations?

Diversity ◽  
2021 ◽  
Vol 13 (5) ◽  
pp. 200
Author(s):  
Eric J. Gangloff ◽  
Sierra Spears ◽  
Laura Kouyoumdjian ◽  
Ciara Pettit ◽  
Fabien Aubret
Keyword(s):  
High Elevation ◽  
Conservation Strategy ◽  
The Novel ◽  
Thermal Physiology ◽  
Treatment Groups ◽  
Thermal Performance Curve ◽  
And Performance ◽  
Thermal Preferences ◽  
High Elevations ◽  
Intense Radiation

Ectothermic animals living at high elevation often face interacting challenges, including temperature extremes, intense radiation, and hypoxia. While high-elevation specialists have developed strategies to withstand these constraints, the factors preventing downslope migration are not always well understood. As mean temperatures continue to rise and climate patterns become more extreme, such translocation may be a viable conservation strategy for some populations or species, yet the effects of novel conditions, such as relative hyperoxia, have not been well characterised. Our study examines the effect of downslope translocation on ectothermic thermal physiology and performance in Pyrenean rock lizards (Iberolacerta bonnali) from high elevation (2254 m above sea level). Specifically, we tested whether models of organismal performance developed from low-elevation species facing oxygen restriction (e.g., hierarchical mechanisms of thermal limitation hypothesis) can be applied to the opposite scenario, when high-elevation organisms face hyperoxia. Lizards were split into two treatment groups: one group was maintained at a high elevation (2877 m ASL) and the other group was transplanted to low elevation (432 m ASL). In support of hyperoxia representing a constraint, we found that lizards transplanted to the novel oxygen environment of low elevation exhibited decreased thermal preferences and that the thermal performance curve for sprint speed shifted, resulting in lower performance at high body temperatures. While the effects of hypoxia on thermal physiology are well-explored, few studies have examined the effects of hyperoxia in an ecological context. Our study suggests that high-elevation specialists may be hindered in such novel oxygen environments and thus constrained in their capacity for downslope migration.

scholarly journals Preparation and Performance Evaluation of Duotone 3D-Printed Polyetheretherketone as Oral Prosthetic Materials: A Proof-of-Concept Study

Polymers ◽  
2021 ◽  
Vol 13 (12) ◽  
pp. 1949
Author(s):  
Ling Ding ◽  
Wei Lu ◽  
Jiaqi Zhang ◽  
Chuncheng Yang ◽  
Guofeng Wu
Keyword(s):  
Titanium Dioxide ◽  
Performance Evaluation ◽  
Mechanical Performance ◽  
Mechanical Tests ◽  
Flexural Properties ◽  
Proof Of Concept ◽  
Tooth Color ◽  
Dental Application ◽  
3D Printed ◽  
And Performance

Literature has reported the successful use of 3D printed polyetheretherketone (PEEK) to fabricate human body implants and oral prostheses. However, the current 3D printed PEEK (brown color) cannot mimic the vivid color of oral tissues and thus cannot meet the esthetical need for dental application. Therefore, titanium dioxide (TiO2) and ferric oxide (Fe2O3) were incorporated into PEEK to prepare a series of tooth-color and gingival-color PEEK composites in this study. Through color measurements and mechanical tests, the color value and mechanical performance of the 3D printed PEEK composites were evaluated. In addition, duotone PEEK specimens were printed by a double nozzle with an interface between tooth-color and gingival-color parts. The mechanical performance of duotone PEEK with two different interfaces (horizontal and vertical) was investigated. With the addition of TiO2 and Fe2O3, the colors of 3D printed PEEK composites become closer to that of dental shade guides. 3D printed PEEK composites generally demonstrated superior tensile and flexural properties and hence have great potential in the dental application. In addition, duotone 3D printed PEEK with a horizontal interfacial orientation presented better mechanical performance than that with a vertical one.

scholarly journals Survival Research Laboratories: A Dystopian Industrial Performance Art

Arts ◽  
2019 ◽  
Vol 8 (1) ◽  
pp. 17
Author(s):  
Nicolas Ballet
Keyword(s):  
Performance Art ◽  
Mechanical Performance ◽  
Common Interest ◽  
The Novel ◽  
Performance Group ◽  
Leading Role ◽  
Industrial Culture ◽  
Industrial Performance ◽  
Machine Art ◽  
Group Survival

This paper examines the leading role played by the American mechanical performance group Survival Research Laboratories (SRL) within the field of machine art during the late 1970s and early 1980s, and as organized under the headings of (a) destruction/survival; (b) the cyborg as a symbol of human/machine interpenetration; and (c) biomechanical sexuality. As a manifestation of the era’s “industrial” culture, moreover, the work of SRL artists Mark Pauline and Eric Werner was often conceived in collaboration with industrial musicians like Monte Cazazza and Graeme Revell, and all of whom shared a common interest in the same influences. One such influence was the novel Crash! by English author J. G. Ballard, and which in turn revealed the ultimate direction in which all of these artists sensed society to be heading: towards a world in which sex itself has fallen under the mechanical demiurge.

Sign in / Sign up

Export Citation Format

Share Document