scholarly journals Can ?Keff be assumed as the driving force for fatigue crack growth?

2015 ◽  
Vol 9 (33) ◽  
pp. 97-104 ◽  
Author(s):  
J.T.P. Castro ◽  
M.A. Meggiolaro ◽  
J.A.O. González
Keyword(s):  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Driving Force

scholarly journals Short fatigue crack growth in welded joints described by the effective cyclic J-integral

2018 ◽  
Vol 165 ◽  
pp. 09002
Author(s):  
Désiré Tchoffo Ngoula ◽  
Michael Vormwald
Keyword(s):  
Fatigue Crack ◽  
Fatigue Life ◽  
Fatigue Crack Growth ◽  
Residual Stresses ◽  
Crack Growth ◽  
Welded Joints ◽  
Driving Force ◽  
J Integral ◽  
Crack Driving Force ◽  
Short Fatigue Crack

The purpose of the present contribution is to predict the fatigue life of welded joints by using the effective cyclic J-integral as crack driving force. The plasticity induced crack closure effects and the effects of welding residual stresses are taken into consideration. Here, the fatigue life is regarded as period of short fatigue crack growth. The node release technique is used to perform finite element based crack growth analyses. For fatigue lives calculations, the effective cyclic J-integral is employed in a relation similar to the Paris (crack growth) equation. For this purpose, a specific code was written for the determination of the effective cyclic J-integral for various lifetime relevant crack lengths. The effects of welding residual stresses on the crack driving force and the calculated fatigue lives are investigated. Results reveal that the influence of residual stresses can be neglected only for large load amplitudes. Finally, the predicted fatigue lives are compared with experimental data: a good accordance between both results is achieved.

A Fatigue Crack Driving Force Parameter

2008 ◽  
Author(s):  
Ying Xiong ◽  
Zengliang Gao ◽  
Junichi Katsuta ◽  
Takeshi Sakiyama
Keyword(s):  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Driving Force ◽  
Crack Tip ◽  
Force Model ◽  
Crack Driving Force ◽  
R Ratio ◽  
Two Parameter ◽  
Better Than

Most of the previous parameters that utilized as a crack driving force were established in modifying the parameter Kop in Elber’s effective SIF range (ΔKeff = Kmax–Kop). This paper focuses on the physical meaning of compliance changes caused by plastic deformation at the crack tip, the test was carried out for structural steel under constant amplitude loading, and differences of several parameter ΔKeff in literature are analyzed quantificationally. The effect of actual stress amplitude at the crack tip on fatigue crack growth is investigated, and improved two-parameter driving force model ΔKdrive(=Kmax)n(ΔK^)1−n) has been proposed. Experimental data for several different types of materials taken from literature were used in the analyses. Presented results indicate that the parameter ΔKdrive is equally effective or better than ΔK(=Kmax-Kmin), ΔKeff(=Kmax-Kop) and ΔK*(=(Kmax)α(ΔK+)1−α) in correlating and predicting the R-ratio effects on fatigue crack growth rate.

Fatigue Crack Growth Prediction under Spectrum Load in an Aluminium Alloy using Crack Driving Force K*eff Approach

2020 ◽  
Vol 12 (3) ◽  
Author(s):  
B. Shailesh Kamath ◽  
A.R. Anilchandra ◽  
T. Sivaranjani ◽  
K. Badari Narayana ◽  
C.M. Manjunath
Keyword(s):  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Aluminium Alloy ◽  
Crack Growth ◽  
Driving Force ◽  
Fatigue Load ◽  
Single Edge ◽  
Crack Driving Force ◽  
Load Sequence ◽  
Better Than

Fatigue Crack Growth (FCG) behaviour in a Single-Edge-Notched Tension (SENT) specimen of 2024-T3 aluminium alloy under a standard mini-FALSTAFF spectrum load sequence was experimentally determined. Further, the FCG behaviour was predicted using cycle-by-cycle method and compared with experimental results. Prediction procedure involved are rain-flow counting of fatigue load cycles, estimation of crack driving force for each of the counted cycle and prediction of crack extension per cycle from constant amplitude crack growth rate equation. In the present work, a new crack driving force (CDF) K*eff involving Kujawski’s crack driving force K* in conjunction with Elber’s crack closure concept was used to account for load interaction effects. FCG prediction was also made using conventional CDF ΔKeff (Elber’s) approach. A good correlation was observed between experimental and predicted FCG behaviour under spectrum loads by the proposed K*eff approach. Also, this prediction was observed to be better than that predicted by conventional ΔKeff approach.

Sign in / Sign up

Export Citation Format

Share Document