scholarly journals Considerations on the choice of experimental parameters in residual stress measurements by hole-drilling and ESPI

2014 ◽  
Vol 8 (30) ◽  
pp. 211-219 ◽  
Author(s):  
C. Barile ◽  
C. Casavola ◽  
G. Pappalettera ◽  
C. Pappalettere
Keyword(s):  
Residual Stress ◽  
Hole Drilling ◽  
Stress Measurements ◽  
Experimental Parameters

Measurement of Residual Stresses in a Nozzle-to-Cylinder Weld After Thermal Ageing at 550°C

2007 ◽  
Author(s):  
S. Hossain ◽  
C. E. Truman ◽  
D. J. Smith ◽  
P. J. Bouchard
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Hoop Stress ◽  
Thermal Ageing ◽  
Hole Drilling ◽  
Stress Profile ◽  
Aged Condition ◽  
Steel Component ◽  
Stress Measurements ◽  
Test Treatment

This paper presents results from a programme of experimental measurements of residual stresses in a type 316H stainless steel component consisting of a nozzle welded to a cylinder. The residual stresses were measured using the deep-hole drilling (DHD) technique. The welded component had been thermally aged in a furnace at 550°C for 19,644 hours prior to the residual stress measurements. Measurements were obtained in the through-thickness section of the component at two locations: (i) in the cylinder heat affected zone (HAZ) at the flank of the nozzle-to-cylinder weld intersection and (ii) in the cylinder HAZ near the crown of the nozzle-to-cylinder weld intersection. The stress measurements made after the furnace heat soak treatment are compared with the earlier as-welded stress measurements. In comparison with as-welded residual stress measurements on the same component and with residual stresses in a service-aged (55,000 hours at 525°C) component, it was evident that the thermal soak test treatment had significantly relaxed the weld residual stresses. In particular the soak test hoop stress profile was almost identical to the service-aged condition, whereas the transverse stress distribution had only been partially relaxed by the thermal soak test.

Determination of Residual Stresses on a Centrifugal Compressor Impeller

2011 ◽  
Author(s):  
Hector Delgado ◽  
Jeff Moore ◽  
Augusto Garcia Hernandez
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Centrifugal Compressor ◽  
Welding Process ◽  
Hole Drilling ◽  
Residual Tensile Stress ◽  
Scanning Method ◽  
Stress Measurements ◽  
Hole Drilling Method ◽  
Compressor Impeller

This paper reports a comparison of two methods to perform residual stress measurements. The specimens tested by each method were two blades from a shrouded centrifugal compressor impeller. The first method is the conventional hole drilling strain gage method which was used to predict residual stresses across the blade surface. The residual stresses are released by drilling a hole in the blade. The second method is called the nonlinear harmonic (NLH) scanning method and is based on the principal that the magnetic domains of ferrous materials vary in a non-linear way relative to internal stress. The effects of residual stress may be either helpful or harmful, depending on the magnitude of the residual with respect to the operating stresses. If not adequately relieved by heat treatment, residual tensile stress that develops in the welding process of shrouded impellers, will add to the stress developed by rotation which moves the point to the right on the Goodman diagram and reduces allowable alternating stress. The results showed comparable residual stress measurements of the NLH method compared to the conventional hole drilling method.

Sign in / Sign up

Export Citation Format

Share Document