Magnetic properties of Nd-Fe-Co-Al rapid solidification alloys

2013 ◽  
Vol 104 (5) ◽  
pp. 471-475
Author(s):  
Nguyen Huy Dan ◽  
Luu Tien Hung
Keyword(s):  
Magnetic Properties ◽  
Rapid Solidification

Structural and low-temperature magnetic properties of as-quenched and annealed Ni–Si–B alloys produced by rapid solidification

2021 ◽  
Vol 132 ◽  
pp. 107140
Author(s):  
M. Ipatov ◽  
V. Zhukova ◽  
L. Dominguez ◽  
K.L. Alvarez ◽  
A. Chizhik ◽  
...  
Keyword(s):  
Magnetic Properties ◽  
Low Temperature ◽  
Rapid Solidification

Improvement of corrosion resistance and magnetic properties of FeCoNiAl0.2Si0.2 high entropy alloy via rapid-solidification

2020 ◽  
Vol 122 ◽  
pp. 106778 ◽  
Author(s):  
Chen Chen ◽  
Hang Zhang ◽  
Yanzhou Fan ◽  
Ran Wei ◽  
Weiwei Zhang ◽  
...  
Keyword(s):  
Magnetic Properties ◽  
Corrosion Resistance ◽  
Rapid Solidification ◽  
High Entropy Alloy ◽  
High Entropy

Magnetic properties of MnBi prepared by rapid solidification

1992 ◽  
Vol 46 (22) ◽  
pp. 14578-14582 ◽  
Author(s):  
X. Guo ◽  
X. Chen ◽  
Z. Altounian ◽  
J. O. Ström-Olsen
Keyword(s):  
Magnetic Properties ◽  
Rapid Solidification

Microstructure and magnetic properties of semi-hard Fe-Co-B-Cu alloys formed by rapid solidification

1994 ◽  
Vol 30 (6) ◽  
pp. 4948-4950
Author(s):  
A. Zaluska ◽  
G. Rudkowska ◽  
P. Rudkowski ◽  
J.O. Strom-Olsen
Keyword(s):  
Magnetic Properties ◽  
Rapid Solidification ◽  
Cu Alloys ◽  
Microstructure And Magnetic Properties

Magnetic properties of Ni-Mn-Ga ribbon prepared by rapid solidification

2002 ◽  
Vol 38 (5) ◽  
pp. 2841-2843 ◽  
Author(s):  
O. Heczko ◽  
P. Svec ◽  
D. Janickovic ◽  
K. Ullakko
Keyword(s):  
Magnetic Properties ◽  
Rapid Solidification

Magnetic Properties of α Fe/NdFeB Nanocomposite Alloys Prepared by Two-Step Rapid Solidification

1999 ◽  
Vol 577 ◽  
Author(s):  
M. Yamasaki ◽  
H. Mizuguchi ◽  
H Morioka ◽  
M. Hamano ◽  
A. Inoue
Keyword(s):  
Magnetic Properties ◽  
Size Distribution ◽  
Rapid Solidification ◽  
Melt Spinning ◽  
Rotor System ◽  
Powder Size ◽  
Lower Side ◽  
Quenching Rate ◽  
Powder Size Distribution ◽  
Bonded Magnet

ABSTRACTIn order to obtain directly powders of nanocomposite a Fe/NdFeB alloys with the composition of NdxFebaICO8NbyB, where x: 8.0-8.5, y: 1.5-2.5, z: 6.0-6.5 in at%, have been prepared using the two-step rapid solidification apparatus, which is composed of a gas atomizing system at the upper side and a collision-and-solidificating rotor system at the lower side. It is found that the coercivity (HcJ) of flat-shaped powders obtained depends on powder sizes. The best HcJ in each sieved powder is 525 kA/m (6.60 kOe) for a size more than 500 p m, 449 kA/m (5.64 kOe) for 150-500 pm, and 391 kA/m (4.91 kOe) for 50-150 p m. These values are not so high compared to those of powders of ribbons prepared using a single-roller melt spinning apparatus. This should be attributed to the powder size distribution that causes fluctuation of the quenching rate. Thickness of the flat powder is found to be controllable up to 70/g m, which is useful to get compression molded bonded magnets with a high density and thus a high remanence (Br). An epoxy-bonded magnet with (BH)max: 61.8 kJ/m 3 (7.76 MGOe), Br: 0.732 T (7.32 kG), HcJ: 427 kA/m (5.36 kOe), and density of 6.20 Mg/m 3 is obtained.

Sign in / Sign up

Export Citation Format

Share Document