Effect of surface roughness on the kinetics of mass transfer during gas carburizing*

2008 ◽  
Vol 63 (5) ◽  
pp. 257-264 ◽  
Author(s):  
O. Karabelchtchikova ◽  
Chr. A. Brown ◽  
R. D. Sisson
Keyword(s):  
Mass Transfer ◽  
Surface Roughness ◽  
Gas Carburizing ◽  
Kinetics Of ◽  
Effect Of Surface

scholarly journals The Effect of Surface Roughness on Diffusion and Chemical Reaction Controlled Limiting Currents on a Rotating Cylinder Electrode in Deaerated Solutions with and Without CO2

CORROSION ◽  
10.5006/2552 ◽  
2018 ◽  
Vol 74 (9) ◽  
pp. 971-983 ◽  
Author(s):  
M. Al-Khateeb ◽  
R. Barker ◽  
A. Neville ◽  
H.M. Thompson
Keyword(s):  
Mass Transfer ◽  
Surface Roughness ◽  
Sherwood Number ◽  
Schmidt Number ◽  
Rotating Cylinder ◽  
Operating Conditions ◽  
Limiting Current ◽  
Surface Roughening ◽  
Rotating Cylinder Electrode ◽  
Effect Of Surface

The influence of surface roughness on mass transfer on a rotating cylinder electrode apparatus is investigated experimentally for a roughness pattern consisting of grooves parallel to the direction of fluid flow. Mass transfer from four different samples, with roughness values of 0.5 μm, 6 μm, 20 μm, and 34 μm, is measured using the limiting current technique for a range of rotational speeds in NaCl solutions saturated with N2 at pH = 3 and 4. Comparison with available correlations for the Sherwood number in literature (which are independent of surface roughness and are either for specific or arbitrary roughness patterns) shows that H+ mass transfer only correlates well for particular levels of roughness and that their accuracy can be increased if a correlation is utilized which is a function of surface roughening. A new correlation for Sherwood number as a function of the Reynolds number, Schmidt number, and surface roughness is proposed which agrees well with the mass transfer observed from all of the rough surface cases considered for this particular roughness pattern. Complementary experiments in CO2 environments were used to assess the combined limiting current associated with H+ and H2CO3 reduction (with the latter occurring via the buffering effect and being associated with the slow CO2 hydration step). Although the increase in sample roughness clearly leads to an increase in the rate of H+ mass transfer, in the CO2 environments considered, surface roughness is found to have no significant influence on the limiting current contribution from H2CO3, which can therefore be determined from Vetter’s equation across this range of operating conditions.

scholarly journals Effect of Surface Roughness on Oxidation Resistance of Stainless Steel AISI 316Ti During Exposure at High Temperature

2020 ◽  
Vol 29 (12) ◽  
pp. 8060-8069
Author(s):  
Wojciech J. Nowak
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Oxidation Resistance ◽  
Surface Preparation ◽  
Surface Region ◽  
Lower Surface ◽  
Near Surface ◽  
Steel Aisi ◽  
Kinetics Of ◽  
Effect Of Surface

AbstractIn the present work, the influence of surface roughness on oxidation kinetics of AISI 316Ti stainless steel and its consequences in term of oxidation resistance were investigated. Namely, the effect of surface roughness on oxidation resistance was evaluated during different types of cyclic oxidation tests at 900 and 1000 °C. The obtained results revealed that alloy possessing higher surface roughness showed longer lifetime compared to that with lower surface roughness. It was also found that more severe cyclic conditions suppressed the positive effect of surface roughness on sample’s lifetime. The better oxidation resistance of rougher alloy was correlated with suppressed formation of Fe-rich nodules on ground surfaces and explained by the combined effect of introduced defects in the near-surface region and possible increase in residual stresses caused by mechanical surface preparation.

EFFECT OF SURFACE ROUGHNESS ON MASS TRANSFER IN A FLAT-PLATE MICROCHANNEL BIOREACTOR

2005 ◽  
Vol 19 (28n29) ◽  
pp. 1559-1562 ◽  
Author(s):  
Y. ZENG ◽  
T. S. LEE ◽  
P. YU ◽  
H. T. LOW
Keyword(s):  
Mass Transfer ◽  
Surface Roughness ◽  
Flat Plate ◽  
Species Concentration ◽  
Solute Depletion ◽  
Smooth Channel ◽  
Dimensional Parameters ◽  
Microfabrication Technique ◽  
Volume Method ◽  
Effect Of Surface

Surface roughness exists in most microfluidic devices due to the microfabrication technique or particle adhesion. In this study, a numerical model based on Finite Volume Method has been developed to simulate the mass transfer in a flat-plate microchannel bioreactor with semi-circular protrusions uniformly distributed on the bottom. The results show that the mass transfer in rough channel is enhanced, as shown by lower minimum species concentration in the rough channel compared with that in smooth channel. Non-dimensional parameters such as Peclet number (Pe), Damkohler number (Da) and the roughness size ratio (β) can influence the effect of roughness greatly. However, it is important to ensure that the minimum species concentration in the rough channel is adequate for cell growth. The results would provide guidance on the perfusion requirements to avoid solute depletion or toxicity during cell culture.

Effect of Surface Roughness on Film Cooling Performance

1985 ◽  
Vol 107 (1) ◽  
pp. 111-116 ◽  
Author(s):  
R. J. Goldstein ◽  
E. R. G. Eckert ◽  
H. D. Chiang ◽  
E. Elovic
Keyword(s):  
Mass Transfer ◽  
Surface Roughness ◽  
Experimental Investigation ◽  
Rough Surface ◽  
Film Cooling ◽  
Free Stream ◽  
Cooling Performance ◽  
Effect Of Surface

An experimental investigation of film cooling on a rough surface has been performed using a mass transfer technique. Two injection geometries (one and two rows of holes) and six roughness patterns were used. The density of the injected gas was close to that of the free-stream air. The presence of roughness causes a decrease in the spanwise-averaged effectiveness for both injection geometries at low blowing rates, and an increase in the effectiveness for one-row injection at high blowing rates, but not for two-row injection. The results for two-row injection (with or without roughness) can be correlated by a parameter used to correlate slot-injection data. The influence of roughness pattern on the average effectiveness and on the lateral uniformity of the effectiveness is described.

Sign in / Sign up

Export Citation Format

Share Document