Air injection at Lake Cachuma, California

1973 ◽  
Author(s):  
M.W. Busby
Keyword(s):  
1970 ◽  
Author(s):  
B. P. Mironov ◽  
M.I. Smirnov ◽  
Nadezhda I. Yarygina

2015 ◽  
Vol 3 (2) ◽  
pp. 15-27
Author(s):  
Ahmed A. Imram ◽  
Humam K. Jalghef ◽  
Falah F. Hatem

     The effect of introducing ramp with a cylindrical slot hole on the film cooling effectiveness has been investigated experimentally and numerically. The film cooling effectiveness measurements are obtained experimentally. A test study was performed at a single mainstream with Reynolds number 76600 at three different coolant to mainstream blowing ratios 1.5, 2, and 3. Numerical simulation is introduced to primarily estimate the best ramp configurations and to predict the behavior of the transport phenomena in the region linked closely to the interaction between the coolant air injection and the hot air mainstram flow. The results showed that using ramps with trench cylindrical holes would enhanced the overall film cooling effectiveness by 83.33% compared with baseline model at blowing ratio of 1.5, also  the best overall flim cooling effectevness was obtained at blowing ratio of 2 while it is reduced at blowing ratio of 3.


2004 ◽  
Vol 39 (3) ◽  
pp. 223-229 ◽  
Author(s):  
Mostafa A. Warith ◽  
Graham J. Takata

Abstract Municipal solid waste (MSW) is slow to stabilize under conventional anaerobic landfill conditions, demanding long-term monitoring and pollution control. Provision of aerobic conditions offers several advantages including accelerated leachate stabilization, increased landfill airspace recovery and a reduction in greenhouse gas emissions. Air injection was applied over 130 days to bench-scale bioreactors containing fresh and aged MSW representative of newly constructed and pre-existing landfill conditions. In the fresh MSW simulation bioreactors, aeration reduced the average time to stabilization of leachate pH by 46 days, TSS by 42 days, TDS by 84 days, BOD5 by 46 days and COD by 32 days. In addition, final leachate concentrations were consistently lower in aerated test cells. There was no indication of a gradual decrease in the concentration of ammonia, and it is likely this high ammonia concentration would continue to be problematic in bioreactor landfill applications. This study focussed only on biodegradability of organics in the solid waste. The concentrations of the nonreactive or conservative substances such as chloride and/or heavy metals remain in the bioreactor landfills due to the continuous recirculation of leachate. The results of this study demonstrate the potential for air injection to accelerate stabilization of municipal solid waste, with greatest influence on fresh waste with a high biodegradable organic fraction.


2021 ◽  
Vol 220 ◽  
pp. 108455
Author(s):  
Siamak Hoseinzadeh ◽  
Ali Sohani ◽  
Stephan Heyns

Processes ◽  
2021 ◽  
Vol 9 (7) ◽  
pp. 1182
Author(s):  
Seung-Jun Kim ◽  
Yong Cho ◽  
Jin-Hyuk Kim

Under low flow-rate conditions, a Francis turbine exhibits precession of a vortex rope with pressure fluctuations in the draft tube. These undesirable flow phenomena can lead to deterioration of the turbine performance as manifested by torque and power output fluctuations. In order to suppress the rope with precession and a swirl component in the tube, the use of anti-swirl fins was investigated in a previous study. However, vortex rope generation still occurred near the cone of the tube. In this study, unsteady-state Reynolds-averaged Navier–Stokes analyses were conducted with a scale-adaptive simulation shear stress transport turbulence model. This model was used to observe the effects of the injection in the draft tube on the unsteady internal flow and pressure phenomena considering both active and passive suppression methods. The air injection affected the generation and suppression of the vortex rope and swirl component depending on the flow rate of the air. In addition, an injection level of 0.5%Q led to a reduction in the maximum unsteady pressure characteristics.


2001 ◽  
Vol 17 (4) ◽  
pp. 263-287 ◽  
Author(s):  
Theron G. Miller ◽  
W. C. Mackay ◽  
David T. Walty

Sign in / Sign up

Export Citation Format

Share Document