scholarly journals EXPERIMENTAL STUDY ON DISTRIBUTION OF COMPRESSIVE STRENGTH OF POROUS CONCRETE

2006 ◽  
Vol 71 (601) ◽  
pp. 9-14
Author(s):  
Takamasa YAMAMOTO ◽  
Shigemitsu HATANAKA ◽  
Naoki MISHIMA ◽  
Sachio KOIKE ◽  
Yukihisa YUASA
Keyword(s):  
Experimental Study ◽  
Compressive Strength ◽  
Porous Concrete

scholarly journals Penetration and Strength Analysis of Pervious Concrete

2021 ◽  
Vol 2070 (1) ◽  
pp. 012244
Author(s):  
Kuldeep Kumar ◽  
Manjeet Bansal ◽  
Rishav Garg ◽  
Rajni Garg
Keyword(s):  
Experimental Study ◽  
Compressive Strength ◽  
Portland Cement ◽  
Coarse Aggregate ◽  
Pervious Concrete ◽  
Strength Analysis ◽  
Porous Concrete ◽  
Fine Aggregates ◽  
Infiltration Tests ◽  
Curing Age

Abstract Porous concrete is an amalgamation of coarse aggregate, Portland cement, and water, which permits rainfall water to permeate through the surface and into the ground before it runs off. Porous concrete encompasses little or no fine aggregates and adequate cementitious fixative to coat the coarse aggregate while keeping the voids interconnected. IRC 44-2017 states that range of permeability for pervious concrete should be from 0.135 cm/second to 1.22 cm/second and array of compressive strength should be 5MPa - 25MPa. In this experimental study, two properties of no fine concrete namely compressive strength and porousness at the curing age of 7th & 28rd days has been targeted. Compressive strength and Infiltration tests were conducted on the pervious concrete of grade M10 and M15 by keeping variation of fine aggregates of 0% - 5%. We observed that fines aggregate help to rise the compressive strength of porous concrete but decrease the permeability. Thus, by careful optimization of the mix, pervious concrete can be obtained for suitable use in low strength load.

scholarly journals Experimental Study on Improvement of Marine Soft Soil with Alkali Residue

2018 ◽  
Vol 53 ◽  
pp. 04021
Author(s):  
SHAO Yong ◽  
LIU Xiao-li ◽  
ZHU Jin-jun
Keyword(s):  
Experimental Study ◽  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Void Ratio ◽  
Soft Soil ◽  
Compressive Modulus ◽  
Engineering Properties ◽  
Test Results ◽  
Use Of Resources ◽  
One Year

Industrial alkali slag is the discharge waste in the process of alkali production. About one million tons of alkali slag is discharged in China in one year. It is a burden on the environment, whether it is directly stacked or discharged into the sea. If we can realize the use of resources, it is a multi-pronged move, so alkali slag is used to improve solidified marine soft soil in this paper. The test results show that the alkali residue can effectively improve the engineering properties of marine soft soil. Among them, the unconfined compressive strength and compressive modulus are increased by about 10 times, and the void ratio and plasticity index can all reach the level of general clay. It shows that alkali slag has the potential to improve marine soft soil and can be popularized in engineering.

Experimental Study on Utilization FGD Byproducts in Building Bricks

2010 ◽  
Vol 150-151 ◽  
pp. 753-757 ◽  
Author(s):  
Xiong Hao Li ◽  
Yong Jie Xue ◽  
Min Zhou
Keyword(s):  
Experimental Study ◽  
Compressive Strength ◽  
Optimum Design ◽  
Power Plants ◽  
Pilot Scale ◽  
Mixture Composition ◽  
Technical Requirement ◽  
Do No Harm ◽  
Maximum Compressive Strength ◽  
Scale Experiment

This paper discussed the feasibility of unburned and non-autoclaved, steam cured bricks prepared by FGD byproducts from coal-fired power plants. The results show that FGD byproduct, aggregates, cementious materials and water could be used to prepare bricks during the process of stir and compaction under natural cure and steam cured condition. S4 and Z2 are the optimum design mixture composition. The maximum compressive strength and saturation coefficient are 28.7 MPa and 96.7%. FGD byproducts do no harm to environment and a pilot-scale experiment demonstrates that bricks made with FGDA can meet the MU10 level bricks technical requirement.

Experimental Study on the Failure Criterion for Brittle Materials in Compression

2011 ◽  
Vol 320 ◽  
pp. 259-262
Author(s):  
Xu Ran ◽  
Zhe Ming Zhu ◽  
Hao Tang
Keyword(s):  
Thin Film ◽  
Experimental Study ◽  
Compressive Strength ◽  
Fracture Mechanics ◽  
Failure Criterion ◽  
Brittle Materials ◽  
Experimental Results ◽  
Experiment Study ◽  
Confining Stress ◽  
Theoretical Results

The mechanical behavior of multi-cracks under compression has become a very important project in the field of fracture mechanics and rock mechanics. In this paper, based on the previous theoretical results of the failure criterion for brittle materials under compression, experiment study is implemented. The specimens are square plates and are made of cement, sand and water, and the cracks are made by using a very thin film (0.1 mm). The relations of material compressive strength versus crack spacing and the lateral confining stress are obtained from experimental results. The experimental results agree well with the failure criterion for brittle materials under compression, which indicates that the criterion is effective and applicable.

Microstructure and Mechanical Properties of Ambiently-Cured Blended Coal Ash-Based Geopolymer Concrete

2016 ◽  
Vol 857 ◽  
pp. 400-404
Author(s):  
Tian Yu Xie ◽  
Togay Ozbakkaloglu
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Compressive Strength ◽  
Fly Ash ◽  
Bottom Ash ◽  
Coal Ash ◽  
Geopolymer Concrete ◽  
Mass Ratio ◽  
Blended Coal ◽  
Microstructure And Mechanical Properties

This paper presents the results of an experimental study on the behavior of fly ash-, bottom ash-, and blended fly and bottom ash-based geopolymer concrete (GPC) cured at ambient temperature. Four bathes of GPC were manufactured to investigate the influence of the fly ash-to-bottom ash mass ratio on the microstructure, compressive strength and elastic modulus of GPC. All the results indicate that the mass ratio of fly ash-to-bottom ash significantly affects the microstructure and mechanical properties of GPCs

Sign in / Sign up

Export Citation Format

Share Document