Combined optical method for monitoring of the physical parameters of thin dielectric films on the surface of single-crystal silicon

2019 ◽  
Vol 11 ◽  
Author(s):  
V. Belyukh ◽  
B. Pavlyk
Keyword(s):  
Single Crystal ◽  
Optical Method ◽  
Single Crystal Silicon ◽  
Dielectric Films ◽  
Physical Parameters ◽  
Crystal Silicon ◽  
Thin Dielectric Films

Analysis of Silicon-On-Insulator Structures Formed By Oxygen Ion Implantation

1985 ◽  
Vol 43 ◽  
pp. 300-301
Author(s):  
N. Lewis ◽  
E. L. Hall ◽  
A. Mogro-Campero ◽  
R. P. Love
Keyword(s):  
Ion Implantation ◽  
Single Crystal ◽  
Single Crystal Silicon ◽  
Silicon Layer ◽  
Device Fabrication ◽  
Silicon On Insulator ◽  
High Dose ◽  
Crystal Silicon ◽  
Oxygen Ion ◽  
Oxygen Ion Implantation

The formation of buried oxide structures in single crystal silicon by high-dose oxygen ion implantation has received considerable attention recently for applications in advanced electronic device fabrication. This process is performed in a vacuum, and under the proper implantation conditions results in a silicon-on-insulator (SOI) structure with a top single crystal silicon layer on an amorphous silicon dioxide layer. The top Si layer has the same orientation as the silicon substrate. The quality of the outermost portion of the Si top layer is important in device fabrication since it either can be used directly to build devices, or epitaxial Si may be grown on this layer. Therefore, careful characterization of the results of the ion implantation process is essential.

scholarly journals The Influence of Wire Speed on Phase Transitions and Residual Stress in Single Crystal Silicon Wafers Sawn by Resin Bonded Diamond Wire Saw

Micromachines ◽  
2021 ◽  
Vol 12 (4) ◽  
pp. 429
Author(s):  
Tengyun Liu ◽  
Peiqi Ge ◽  
Wenbo Bi
Keyword(s):  
Residual Stress ◽  
Surface Layer ◽  
Phase Transitions ◽  
Single Crystal ◽  
Amorphous Silicon ◽  
Silicon Wafer ◽  
Single Crystal Silicon ◽  
Silicon Wafers ◽  
Crystal Silicon ◽  
Diamond Wire

Lower warp is required for the single crystal silicon wafers sawn by a fixed diamond wire saw with the thinness of a silicon wafer. The residual stress in the surface layer of the silicon wafer is the primary reason for warp, which is generated by the phase transitions, elastic-plastic deformation, and non-uniform distribution of thermal energy during wire sawing. In this paper, an experiment of multi-wire sawing single crystal silicon is carried out, and the Raman spectra technique is used to detect the phase transitions and residual stress in the surface layer of the silicon wafers. Three different wire speeds are used to study the effect of wire speed on phase transition and residual stress of the silicon wafers. The experimental results indicate that amorphous silicon is generated during resin bonded diamond wire sawing, of which the Raman peaks are at 178.9 cm−1 and 468.5 cm−1. The ratio of the amorphous silicon surface area and the surface area of a single crystal silicon, and the depth of amorphous silicon layer increases with the increasing of wire speed. This indicates that more amorphous silicon is generated. There is both compressive stress and tensile stress on the surface layer of the silicon wafer. The residual tensile stress is between 0 and 200 MPa, and the compressive stress is between 0 and 300 MPa for the experimental results of this paper. Moreover, the residual stress increases with the increase of wire speed, indicating more amorphous silicon generated as well.

scholarly journals Novel Abrasive-Impregnated Pads and Diamond Plates for the Grinding and Lapping of Single-Crystal Silicon Carbide Wafers

2021 ◽  
Vol 11 (4) ◽  
pp. 1783
Author(s):  
Ming-Yi Tsai ◽  
Kun-Ying Li ◽  
Sun-Yu Ji
Keyword(s):  
Silicon Carbide ◽  
Wear Rate ◽  
Single Crystal ◽  
Traditional Method ◽  
Removal Rate ◽  
Chemical Mechanical Planarization ◽  
Single Crystal Silicon ◽  
Crystal Silicon ◽  
Diamond Grit ◽  
Ceramic Binder

In this study, special ceramic grinding plates impregnated with diamond grit and other abrasives, as well as self-made lapping plates, were used to prepare the surface of single-crystal silicon carbide (SiC) wafers. This novel approach enhanced the process and reduced the final chemical mechanical planarization (CMP) polishing time. Two different grinding plates with pads impregnated with mixed abrasives were prepared: one with self-modified diamond + SiC and a ceramic binder and one with self-modified diamond + SiO2 + Al2O3 + SiC and a ceramic binder. The surface properties and removal rate of the SiC substrate were investigated and a comparison with the traditional method was conducted. The experimental results showed that the material removal rate (MRR) was higher for the SiC substrate with the mixed abrasive lapping plate than for the traditional method. The grinding wear rate could be reduced by 31.6%. The surface roughness of the samples polished using the diamond-impregnated lapping plate was markedly better than that of the samples polished using the copper plate. However, while the surface finish was better and the grinding efficiency was high, the wear rate of the mixed abrasive-impregnated polishing plates was high. This was a clear indication that this novel method was effective and could be used for SiC grinding and lapping.

Sign in / Sign up

Export Citation Format

Share Document