scholarly journals An Equivalent Truss Model for In-Plane Nonlinear Analysis of Unreinforced Masonry Walls

2018 ◽  
Vol 4 (4) ◽  
pp. 828 ◽  
Author(s):  
Mohammadamir Najafgholipour
Keyword(s):  
Shear Failure ◽  
Computational Cost ◽  
Failure Criteria ◽  
Unreinforced Masonry ◽  
Masonry Wall ◽  
Seismic Evaluation ◽  
Plane Failure ◽  
Seismic Performance Evaluation ◽  
Truss Model ◽  
Performance Based Seismic Design

According to the importance of seismic evaluation of existing unreinforced masonry (URM) buildings, researchers have been interested in numerical modelling of these types of structures and their components. On the other hand, in seismic performance evaluation and retrofitting codes which are mostly based on Performance Based Seismic Design (PBSD), different analysis methods such as linear and nonlinear, static and dynamic analyses are employed. Therefore, simple equivalent frame models with lower computational cost are very useful for modelling and analysis of unreinforced masonry buildings. In this article, a simple equivalent truss model is proposed for modelling and analysis of an unreinforced masonry wall with sliding shear failure as the governing in-plane failure mode. The model is developed according to an analogy between the internal forces in a triangular truss and the Mohr-Coulomb failure criteria. Then, the proposed model is generalized for modelling and push over analysis of combinations of walls. Finally, the modelling procedure is applied for push over analysis of an unreinforced masonry wall consists of some piers and the push over curve of the wall is determined and discussed.

scholarly journals Experimental Study on Dynamic Behavior of Unreinforced Masonry Walls

2013 ◽  
Vol 8 (2) ◽  
pp. 305-311 ◽  
Author(s):  
Taiki Saito ◽  
◽  
Luis Moya ◽  
Cesar Fajardo ◽  
Koichi Morita ◽  
...  
Keyword(s):  
Dynamic Behavior ◽  
Failure Mode ◽  
Shear Failure ◽  
Shaking Table Test ◽  
Unreinforced Masonry ◽  
Masonry Wall ◽  
Shaking Table ◽  
Masonry Walls ◽  
Plane Failure ◽  
Out Of Plane

The dynamic behavior of an unreinforced masonry wall is investigated through a shaking table test of two specimens. In order to represent a non-engineering one-story house, the first specimen consists of a Cshaped structure with masonry walls connected only at their ends. The second specimen is built to represent an upper story, so the C wall is connected at the top by a wooden diaphragm floor, and a weight is suspended onto it. The test results show each specimen exhibits different behaviors. In the first specimen, an out-of-plane failure mode governs. In the second specimen, a shear failure mode governs.

scholarly journals Numerical Modeling of Unreinforced Masonry Walls Strengthened with Fe-Based Shape Memory Alloy Strips

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2961
Author(s):  
Moein Rezapour ◽  
Mehdi Ghassemieh ◽  
Masoud Motavalli ◽  
Moslem Shahverdi
Keyword(s):  
Energy Dissipation ◽  
Shape Memory Alloy ◽  
Shape Memory ◽  
Unreinforced Masonry ◽  
Masonry Wall ◽  
Masonry Walls ◽  
Vertical Strip ◽  
Maximum Resistance ◽  
The Cross ◽  
Post Tensioning

This study presents a new way to improve masonry wall behavior. Masonry structures comprise a significant part of the world’s structures. These structures are very vulnerable to earthquakes, and their performances need to be improved. One way to enhance the performances of such types of structures is the use of post-tensioning reinforcements. In the current study, the effects of shape memory alloy as post-tensioning reinforcements on originally unreinforced masonry walls were investigated using finite element simulations in Abaqus. The developed models were validated based on experimental results in the literature. Iron-based shape memory alloy strips were installed on masonry walls by three different configurations, namely in cross or vertical forms. Seven macroscopic masonry walls were modeled in Abaqus software and were subjected to cyclic loading protocol. Parameters such as stiffness, strength, durability, and energy dissipation of these models were then compared. According to the results, the Fe-based strips increased the strength, stiffness, and energy dissipation capacity. So that in the vertical-strip walls, the stiffness increases by 98.1%, and in the cross-strip model's position, the stiffness increases by 127.9%. In the vertical-strip model, the maximum resistance is equal to 108 kN, while in the end cycle, this number is reduced by almost half and reaches 40 kN, in the cross-strip model, the maximum resistance is equal to 104 kN, and in the final cycle, this number decreases by only 13.5% and reaches 90 kN. The scattering of Fe-based strips plays an important role in energy dissipation. Based on the observed behaviors, the greater the scattering, the higher the energy dissipation. The increase was more visible in the walls with the configuration of the crossed Fe-based strips.

scholarly journals Analytical investigation of high-velocity impact on hybrid unidirectional/woven composite panels

2016 ◽  
Vol 30 (4) ◽  
pp. 545-563 ◽  
Author(s):  
H Shanazari ◽  
GH Liaghat ◽  
H Hadavinia ◽  
A Aboutorabi
Keyword(s):  
Cross Sections ◽  
Shear Failure ◽  
Failure Criteria ◽  
Analytical Investigation ◽  
Woven Fabrics ◽  
Body Armor ◽  
Ballistic Performance ◽  
Nonwoven Fabrics ◽  
Ballistic Protection ◽  
Maximum Tensile Strain

In addition to fiber properties, the fabric structure plays an important role in determining ballistic performance of composite body armor textile. Textile structures used in ballistic protection are woven fabrics, unidirectional (UD) fabric structures, and nonwoven fabrics. In this article, an analytical model based on wave propagation and energy balance between the projectile and the target is developed to analyze hybrid fabric panels for ballistic protection. The hybrid panel consists of two types of structure: woven fabrics as the front layers and UD material as the rear layers. The model considers different cross sections of surface of the target in the woven and UD fabric of the hybrid panel. Also the model takes into account possible shear failure by using shear strength together with maximum tensile strain as the failure criteria. Reflections of deformation waves at interface between the layers and also the crimp of the yarn are modeled in the woven part of the hybrid panel. The results show greater efficiency of woven fibers in front layers (more shear resistance) and UD yarns in the rear layers (more tensile resistance), leading to better ballistic performance. Also modeling the yarn crimp results in more trauma at the backface of the panel producing data closer to the experimental results. It was found that there is an optimum ratio of woven to UD materials in the hybrid ballistic panel.

Research Situation on the Performance-Based Seismic Design Method for Reinforced Concrete Structure

2010 ◽  
Vol 163-167 ◽  
pp. 1757-1761
Author(s):  
Yong Le Qi ◽  
Xiao Lei Han ◽  
Xue Ping Peng ◽  
Yu Zhou ◽  
Sheng Yi Lin
Keyword(s):  
Reinforced Concrete ◽  
Seismic Design ◽  
Design Method ◽  
Concrete Structures ◽  
Reinforced Concrete Structures ◽  
Seismic Evaluation ◽  
Seismic Codes ◽  
Performance Based Seismic Design ◽  
Capacity Calculation ◽  
Seismic Design Method

Various analytical approaches to performance-based seismic design are in development. Based on the current Chinese seismic codes，elastic capacity calculation under frequent earthquake and ductile details of seismic design shall be performed for whether seismic design of new buildings or seismic evaluation of existing buildings to satisfy the seismic fortification criterion “no damage under frequent earthquake, repairable under fortification earthquake, no collapse under severe earthquake”. However, for some special buildings which dissatisfy with the requirements of current building codes, elastic capacity calculation under frequent earthquake is obviously not enough. In this paper, the advanced performance-based seismic theory is introduced to solve the problems of seismic evaluation and strengthening for existing reinforced concrete structures, in which story drift ratio and deformation of components are used as performance targets. By combining the features of Chinese seismic codes, a set of performance-based seismic design method is established for reinforced concrete structures. Different calculation methods relevant to different seismic fortification criterions are adopted in the proposed method, which solve the problems of seismic evaluation for reinforced concrete structures.

A numerical approach to predict soil bearing potential for isolated footing

2021 ◽  
Author(s):  
Gilbert Hinge ◽  
Jayanta Kumar Das ◽  
Biswadeep Bharali
Keyword(s):  
Bearing Capacity ◽  
Shear Failure ◽  
Correlation Coefficients ◽  
Failure Criteria ◽  
Numerical Approach ◽  
Ultimate Bearing Capacity ◽  
Foundation Design ◽  
Advantages And Disadvantages ◽  
Local Shear ◽  
Failure Conditions

<p>The success of any civil engineering structure's foundation design depends upon the accuracy of estimation of soil’s ultimate bearing capacity. Numerous numerical approaches have been proposed to estimate the foundation's bearing capacity value to avoid repetitive and expensive experimental work. All these models have their advantages and disadvantages. In this study, we compiled all the governing equations mentioned in Bureau of Indian standard IS:6403-1981 and modify the equation for Ultimate Bearing Capacity. The equation was modified by considering two new parameters, K1(for general shear) and K2 (for local shear) so that a common governing equation can be used for both general and local shear failure criteria. The program used for running the model was written in MATLAB language code and verified with the observed field data. Results indicate that the proposed model accurately characterized the ultimate, safe, and allowable bearing capacity of a shallow footing at different depths. The correlation coefficients between the observed and model-predicted bearing capacity values for a 2m foundation depth with footing size of 1.5 ×1.5, 2.0 × 2.0, and 2.5 × 2.5 m are 0.95, 0.94, and 0.96. A similar result was noted for the other foundation depth and footing size. Findings show that the model can be used as a reliable tool for predicting the bearing capacity of shallow foundations at any given depth.  Moreover, the formulated model can also be used for the transition zone between general and local shear failure conditions.</p>

Strength Simulation of Woven Fabric Composite Materials With Material Nonlinearity Using Micromechanics Based Model

2000 ◽  
Author(s):  
A. Tabiei ◽  
G. Song ◽  
Y. Jiang
Keyword(s):  
Finite Element ◽  
Shear Failure ◽  
Material Model ◽  
Failure Criteria ◽  
Woven Fabric ◽  
Woven Composites ◽  
Explicit Finite Element ◽  
Representative Cell ◽  
Pure Matrix ◽  
Transverse Failure

Abstract The objective of the current investigation is to predict failure strength of woven composites, which considers the two-dimensional extent of woven fabric, based on micro-mechanics. The formulation has an interface with nonlinear finite element codes. At each load increment, global stresses and strains are communicated to the representative cell and subsequently distributed to each subcell. Once stresses and strains are associated to a subcell they can be distributed to each constituent of the subcell (i.e. fill, warp, and resin). Consequently micro-failure criteria (MFC) are defined for each constituents of a subcell and the proper stiffness degradation is modeled. Different stages of failure such as warp transverse failure, fill transverse failure, failure of pure matrix in longitudinal and shear, shear failure in fill and warp, and fiber in fill and warp in longitudinal tension are considered. Good correlation is observed between the predicted and the experimental results presented in the published literature. This material model is suitable for implicit failure analysis under static loads and is being modified for explicit finite element codes to deal with problems such as crashworthiness and impact.

scholarly journals An Approach for Stability Analysis of Gas/Fluid-Filled Cylindrical Hole in Laminated Materials

2020 ◽  
Vol 2020 ◽  
pp. 1-15
Author(s):  
Song Leng ◽  
Li Hou ◽  
Yang Duan
Keyword(s):  
Failure Criterion ◽  
Shear Failure ◽  
Cylindrical Hole ◽  
Material Strength ◽  
Strength Anisotropy ◽  
Plane Failure ◽  
Hole Wall ◽  
Weak Plane ◽  
Laminated Materials ◽  
Laminated Structures

An explicit analytical workflow for cylindrical hole stability analyses in general laminated materials that possess transversely isotropic (TI) anisotropy is presented. In this approach, the calculation of the distribution of the stresses around a cylindrical hole and the failure evaluation at the hole wall consider the effects of both material elasticity anisotropy and strength anisotropy caused by material laminated structures. Material strength anisotropy is assumed to be caused by the sliding of preexisting weakness planes oriented parallel to the isotropic plane of the material. The effect of anisotropy on strength is modeled by combining a shear failure criterion for the intact matrix and a weak plane failure criterion for the planes of weakness. We derive critical pressure solutions for the stability of the intact matrix around a hole filled with gas or fluid based on the Mohr–Coulomb failure criterion and Drucker–Prager failure criterion; either one of them can be combined with the weak plane failure criterion to give the solution for hole wall shear failure pressure. The solution for hole wall fracture initiation pressure is derived based on the tensile failure criterion. This approach can be applied to holes of arbitrary orientation in general laminated materials.

Sign in / Sign up

Export Citation Format

Share Document