Reducing Shock Interactions in a Single Stage High Pressure Turbine via 3D Aerodynamic Shaping

2013 ◽  
Author(s):  
Braden Hancock
Keyword(s):  
High Pressure ◽  
Single Stage ◽  
High Pressure Turbine ◽  
Shock Interactions

Development of New Single and High-Density Heat-Flux Gauges for Unsteady Heat Transfer Measurements for a Rotating Transonic Turbine

2020 ◽  
Author(s):  
Richard Celestina ◽  
Spencer Sperling ◽  
Louis Christensen ◽  
Randall Mathison ◽  
Hakan Aksoy ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
High Pressure ◽  
Pressure Ratio ◽  
High Density ◽  
Secondary Flows ◽  
Single Stage ◽  
High Pressure Turbine ◽  
Transonic Turbine ◽  
New Generation

Abstract This paper presents the development and implementation of a new generation of double-sided heat-flux gauges at The Ohio State University Gas Turbine Laboratory (GTL) along with heat transfer measurements for film-cooled airfoils in a single-stage high-pressure transonic turbine operating at design corrected conditions. Double-sided heat flux gauges are a critical part of turbine cooling studies, and the new generation improves upon the durability and stability of previous designs while also introducing high-density layouts that provide better spatial resolution. These new customizable high-density double-sided heat flux gauges allow for multiple heat transfer measurements in a small geometric area such as immediately downstream of a row of cooling holes on an airfoil. Two high-density designs are utilized: Type A consists of 9 gauges laid out within a 5 mm by 2.6 mm (0.20 inch by 0.10 inch) area on the pressure surface of an airfoil, and Type B consists of 7 gauges located at points of predicted interest on the suction surface. Both individual and high-density heat flux gauges are installed on the blades of a transonic turbine experiment for the second build of the High-Pressure Turbine Innovative Cooling program (HPTIC2). Run in a short duration facility, the single-stage high-pressure turbine operated at design-corrected conditions (matching corrected speed, flow function, and pressure ratio) with forward and aft purge flow and film-cooled blades. Gauges are placed at repeated locations across different cooling schemes in a rainbow rotor configuration. Airfoil film-cooling schemes include round, fan, and advanced shaped cooling holes in addition to uncooled airfoils. Both the pressure and suction surfaces of the airfoils are instrumented at multiple wetted distance locations and percent spans from roughly 10% to 90%. Results from these tests are presented as both time-average values and time-accurate ensemble averages in order to capture unsteady motion and heat transfer distribution created by strong secondary flows and cooling flows.

Using CFD to Reduce Resonant Stresses on a Single-Stage, High-Pressure Turbine Blade

2002 ◽  
Author(s):  
J. P. Clark ◽  
A. S. Aggarwala ◽  
M. A. Velonis ◽  
R. E. Gacek ◽  
S. S. Magge ◽  
...  
Keyword(s):  
High Pressure ◽  
Turbine Blade ◽  
Guide Vane ◽  
Turbine Blades ◽  
Suction Side ◽  
Lessons Learned ◽  
Single Stage ◽  
Navier Stokes ◽  
High Pressure Turbine ◽  
Time Resolved

The ability to predict levels of unsteady forcing on high-pressure turbine blades is critical to avoid high-cycle fatigue failures. In this study, 3D time-resolved computational fluid dynamics is used within the design cycle to predict accurately the levels of unsteady forcing on a single-stage high-pressure turbine blade. Further, nozzle-guide-vane geometry changes including asymmetric circumferential spacing and suction-side modification are considered and rigorously analyzed to reduce levels of unsteady blade forcing. The latter is ultimately implemented in a development engine, and it is shown successfully to reduce resonant stresses on the blade. This investigation builds upon data that was recently obtained in a full-scale, transonic turbine rig to validate a Reynolds-Averaged Navier-Stokes (RANS) flow solver for the prediction of both the magnitude and phase of unsteady forcing in a single-stage HPT and the lessons learned in that study.

Design and Test Results of a Ultra High Loaded Single Stage High Pressure Turbine

2013 ◽  
Author(s):  
Harjit S. Hura ◽  
Scott Carson ◽  
Rob Saeidi ◽  
Hyoun-Woo Shin ◽  
Paul Giel
Keyword(s):  
High Pressure ◽  
Total Pressure ◽  
High Speed ◽  
Pressure Ratio ◽  
Single Stage ◽  
Test Results ◽  
High Pressure Turbine ◽  
Technology Program ◽  
High Pressure Ratio ◽  
Expected Performance

This paper describes the engine and rig design, and test results of an ultra-highly loaded single stage high pressure turbine. In service aviation single stage HPTs typically operate at a total-to-total pressure ratio of less than 4.0. At higher pressure ratios or energy extraction the nozzle and blade both have regions of supersonic flow and shock structures which, if not mitigated, can result in a large loss in efficiency both in the turbine itself and due to interaction with the downstream component which may be a turbine center frame or a low pressure turbine. Extending the viability of the single stage HPT to higher pressure ratios is attractive as it enables a compact engine with less weight, and lower initial and maintenance costs as compared to a two stage HPT. The present work was performed as part of the NASA UEET (Ultra-Efficient Engine Technology) program from 2002 through 2005. The goal of the program was to design and rig test a cooled single stage HPT with a pressure ratio of 5.5 with an efficiency at least two points higher than the state of the art. Preliminary design tools and a design of experiments approach were used to design the flow path. Stage loading and through-flow were set at appropriate levels based on prior experience on high pressure ratio single stage turbines. Appropriate choices of blade aspect ratio, count, and reaction were made based on comparison with similar HPT designs. A low shock blading design approach was used to minimize the shock strength in the blade during design iterations. CFD calculations were made to assess performance. The HPT aerodynamics and cooling design was replicated and tested in a high speed rig at design point and off-design conditions. The turbine met or exceeded the expected performance level based on both steady state and radial/circumferential traverse data. High frequency dynamic total pressure measurements were made to understand the presence of unsteadiness that persists in the exhaust of a transonic turbine.

Time-Averaged and Time-Accurate Aero-Dynamics for the Recessed Tip Cavity of a High-Pressure Turbine Blade and the Outer Stationary Shroud: Comparison of Computational and Experimental Results

2004 ◽  
Author(s):  
Brian R. Green ◽  
John W. Barter ◽  
Charles W. Haldeman ◽  
Michael G. Dunn
Keyword(s):  
High Pressure ◽  
Turbine Blade ◽  
Computational Models ◽  
Turbine Rotor ◽  
Single Stage ◽  
Cfd Modeling ◽  
Blade Surface ◽  
High Pressure Turbine ◽  
Pressure Transducers ◽  
Blade Tip

The unsteady aero-dynamics of a single-stage high-pressure turbine blade operating at design corrected conditions has been the subject of a thorough study involving detailed measurements and computations. The experimental configuration consisted of a single-stage high-pressure turbine and the adjacent, downstream, low-pressure turbine nozzle row. All three blade-rows were instrumented at three spanwise locations with flush-mounted, high frequency response pressure transducers. The rotor was also instrumented with the same transducers on the blade tip and platform and the stationary shroud was instrumented with pressure transducers at specific locations above the rotating blade. Predictions of the time-dependent flow field around the rotor were obtained using MSU-TURBO, a 3D, non-linear, computational fluid dynamics (CFD) code. Using an isolated blade-row unsteady analysis method, the unsteady surface pressure for the high-pressure turbine rotor due to the upstream high-pressure turbine nozzle was calculated. The predicted unsteady pressure on the rotor surface was compared to the measurements at selected spanwise locations on the blade, in the recessed cavity, and on the shroud. The rig and computational models included a flat and recessed blade tip geometry and were used for the comparisons presented in the paper. Comparisons of the measured and predicted static pressure loading on the blade surface show excellent correlation from both a time-average and time-accurate standpoint. This paper concentrates on the tip and shroud comparisons between the experiments and the predictions and these results also show good correlation with the time-resolved data. These data comparisons provide confidence in the CFD modeling and its ability to capture unsteady flow physics on the blade surface, in the flat and recessed tip regions of the blade, and on the stationary shroud.

Large Eddy Simulation of Combustor and Complete Single-Stage High-Pressure Turbine of the FACTOR Test Rig

2019 ◽  
Author(s):  
Martin Thomas ◽  
Jerome Dombard ◽  
Florent Duchaine ◽  
Laurent Gicquel ◽  
Charlie Koupper
Keyword(s):  
High Pressure ◽  
Large Eddy Simulation ◽  
Combustion Chamber ◽  
Measurement Data ◽  
Single Stage ◽  
High Pressure Turbine ◽  
Lean Burn ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Compact Design

Abstract Development goals for next generation aircraft engines are mainly determined by the need to reduce fuel consumption and environmental impact. To reduce NOx emissions lean combustion technologies will be applied in future development projects. The more compact design and the absence of dilution holes in this type of engines shortens residence times in the combustion chamber and reduces mixing which results in higher levels of swirl, turbulence and temperature distortions at the exit of the combustion chamber. For these engines interactions between components are more important, so that the traditional engine design approach of component-wise optimization will have to be adapted. To study new lean burn architectures the European FACTOR project investigates the transport of hot streaks produced by a non-reactive combustor simulator through a single stage high-pressure turbine. In this work high-fidelity Large Eddy Simulation (LES) of combustor and complete high-pressure turbine are discussed and validated against experimental data. Measurement data is available on P40 (exit of the combustion chamber), P41 (exit of the stator) and P42 (exit of the rotor) and generally shows a good agreement to LES data.

Averaged and Time-Dependent Aerodynamics of a High Pressure Turbine Blade Tip Cavity and Stationary Shroud: Comparison of Computational and Experimental Results

2004 ◽  
Vol 127 (4) ◽  
pp. 736-746 ◽  
Author(s):  
Brian R. Green ◽  
John W. Barter ◽  
Charles W. Haldeman ◽  
Michael G. Dunn
Keyword(s):  
High Pressure ◽  
Turbine Blade ◽  
Computational Models ◽  
Single Stage ◽  
Time Dependent ◽  
Cfd Modeling ◽  
Blade Surface ◽  
High Pressure Turbine ◽  
Pressure Transducers ◽  
Blade Tip

The unsteady aero-dynamics of a single-stage high-pressure turbine blade operating at design corrected conditions has been the subject of a thorough study involving detailed measurements and computations. The experimental configuration consisted of a single-stage high-pressure turbine and the adjacent, downstream, low-pressure turbine nozzle row. All three blade-rows were instrumented at three spanwise locations with flush-mounted, high-frequency response pressure transducers. The rotor was also instrumented with the same transducers on the blade tip and platform and the stationary shroud was instrumented with pressure transducers at specific locations above the rotating blade. Predictions of the time-dependent flow field around the rotor were obtained using MSU-TURBO, a three-dimensional (3D), nonlinear, computational fluid dynamics (CFD) code. Using an isolated blade-row unsteady analysis method, the unsteady surface pressure for the high-pressure turbine rotor due to the upstream high-pressure turbine nozzle was calculated. The predicted unsteady pressure on the rotor surface was compared to the measurements at selected spanwise locations on the blade, in the recessed cavity, and on the shroud. The rig and computational models included a flat and recessed blade tip geometry and were used for the comparisons presented in the paper. Comparisons of the measured and predicted static pressure loading on the blade surface show excellent correlation from both a time-average and time-accurate standpoint. This paper concentrates on the tip and shroud comparisons between the experiments and the predictions and these results also show good correlation with the time-resolved data. These data comparisons provide confidence in the CFD modeling and its ability to capture unsteady flow physics on the blade surface, in the flat and recessed tip regions of the blade, and on the stationary shroud.

Design and Test of a Highly Loaded Single-Stage High Pressure Turbine

2011 ◽  
Author(s):  
T. Wolf ◽  
E. Janke ◽  
R. Benton ◽  
F. Kost ◽  
F. Haselbach ◽  
...  
Keyword(s):  
High Pressure ◽  
Single Stage ◽  
Medium Size ◽  
Attractive Alternative ◽  
Efficient Design ◽  
High Pressure Turbine ◽  
Comparison Of Experiments ◽  
Performance Area ◽  
Aero Engines ◽  
Highly Loaded

For the small to medium thrust range of modern aero engines, highly loaded single-stage HP turbines facilitate an attractive alternative to a more conventional 2-stage HPT architecture. Within the German government funded LUFO-3 programme “Transonic Single Stage High-Pressure Turbine”, a substantial activity towards the development and test of supersonic aerodynamic technology for single stage turbines was launched in 2003. This paper describes fundamental aerodynamic concept studies and related cascade experiments in support of a future highly loaded high-pressure turbine architecture. Details of the first out of two builds featuring an engine representative single-stage HPT is described in detail. Focus will be on instrumentation design, selected results from performance, area traverse and unsteady blade surface pressure measurements and the comparison of experiments with numerical simulations. The successfully completed test campaign confirms the existence of an aerodynamically efficient design of a highly loaded HPT, thereby enabling a competitive building block for a small to medium size engine concept.

scholarly journals Installation of a Turbine Stage in the Pyestock Isentropic Light Piston Facility

1994 ◽  
Author(s):  
M. A. Hilditch ◽  
A. Fowler ◽  
T. V. Jones ◽  
K. S. Chana ◽  
M. L. G. Oldfield ◽  
...  
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Single Stage ◽  
Constant Speed ◽  
Turbine Stage ◽  
High Pressure Turbine ◽  
Dimensional Parameters ◽  
Run Time ◽  
Annular Cascade

The Isentropic Light Piston Facility (ILPF) at Pyestock has been upgraded to include a single stage, high pressure turbine. All major non-dimensional parameters are accurately scaled during the 0.4s run time, enabling heat transfer and aerodynamic measurements to be made at engine representative conditions. The ILPF was previously an annular cascade facility. This paper describes the design and integration of the rotor module and the results of the commissioning tests. An important feature is a novel, patented, turbobrake which is shown to maintain the turbine at a constant speed during the run.

Comparison of Harmonic and Time Marching Unsteady Computational Fluid Dynamics Solutions With Measurements for a Single-Stage High-Pressure Turbine

2013 ◽  
Vol 136 (1) ◽  
Author(s):  
Brian R. Green ◽  
Randall M. Mathison ◽  
Michael G. Dunn
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
High Pressure ◽  
Flow Path ◽  
Single Stage ◽  
Phase Lag ◽  
High Pressure Turbine ◽  
Rotating Blade ◽  
Time Marching ◽  
Turbine Flow Path

The unsteady aerodynamics of a single-stage high-pressure turbine has been the subject of a study involving detailed measurements and computations. Data and predictions for this experiment have been presented previously, but the current study compares predictions obtained using the nonlinear harmonic simulation method to results obtained using a time-marching simulation with phase-lag boundary conditions. The experimental configuration consisted of a single-stage high-pressure turbine (HPT) and the adjacent, downstream, low-pressure turbine nozzle row (LPV) with an aerodynamic design that is typical to that of a commercial high-pressure ratio HPT and LPV. The flow path geometry was equivalent to engine hardware and operated at the proper design-corrected conditions to match cruise conditions. The high-pressure vane and blade were uncooled for these comparisons. All three blade rows are instrumented with flush-mounted, high-frequency response pressure transducers on the airfoil surfaces and the inner and outer flow path surfaces, which include the rotating blade platform and the stationary shroud above the rotating blade. Predictions of the time-dependent flow field for the turbine flow path were obtained using a three-dimensional, Reynolds-averaged Navier–Stokes computational fluid dynamics (CFD) code. Using a two blade row computational model of the turbine flow path, the unsteady surface pressure for the high-pressure vane and rotor was calculated using both unsteady methods. The two sets of predictions are then compared to the measurements looking at both time-averaged and time-accurate results, which show good correlation between the two methods and the measurements. This paper concentrates on the similarities and differences between the two unsteady methods, and how the predictions compare with the measurements since the faster harmonic solution could allow turbomachinery designers to incorporate unsteady calculations in the design process without sacrificing accuracy when compared to the phase-lag method.

Sign in / Sign up

Export Citation Format

Share Document