Multi-Evaporator Two-Phase Loop Cooling System

2006 ◽  
Author(s):  
David Bugby ◽  
Terri Miller ◽  
Jeff Baker
Keyword(s):  
Cooling System ◽  
Two Phase ◽  
Phase Loop

Electronics Thermal Management Using Advanced Hybrid Two-Phase Loop Technology

2007 ◽  
Author(s):  
Chanwoo Park ◽  
Aparna Vallury ◽  
Jon Zuo ◽  
Jeffrey Perez ◽  
Paul Rogers
Keyword(s):  
Thermal Management ◽  
High Performance ◽  
Cooling System ◽  
Active Flow Control ◽  
Heat Pipes ◽  
High Heat ◽  
Heat Fluxes ◽  
Significant Advance ◽  
Two Phase ◽  
Phase Loop

The paper discusses an advanced Hybrid Two-Phase Loop (HTPL) technology for electronics thermal management. The HTPL combined active mechanical pumping with passive capillary pumping realizing a reliable yet high performance cooling system. The evaporator developed for the HTPL used 3-dimensional metallic wick structures to enhance boiling heat transfer by passive capillary separation of liquid and vapor phases. Through the testing using various prototype hybrid loops, it was demonstrated that the hybrid loops were capable of removing high heat fluxes from multiple heat sources with large surface areas up to 135cm2 and 10kW heat load. Because of the passive capillary phase separation, the hybrid loop operation didn’t require any active flow control of the liquid in the evaporator, even at highly transient and asymmetrical heat inputs between the evaporators. These results represent the significant advance over state-of-the-art heat pipes, loop heat pipes and evaporative spray cooling devices in terms of performance, robustness and simplicity.

scholarly journals Numerical Study of a Cooling System Using Phase Change of a Refrigerant in a Thermosyphon

Energies ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3634
Author(s):  
Grzegorz Czerwiński ◽  
Jerzy Wołoszyn
Keyword(s):  
Mass Transfer ◽  
Phase Change ◽  
Heat Dissipation ◽  
Cooling System ◽  
Numerical Study ◽  
Relaxation Parameter ◽  
Phase Changes ◽  
Transfer Time ◽  
Two Phase ◽  
Time Relaxation

With the increasing trend toward the miniaturization of electronic devices, the issue of heat dissipation becomes essential. The use of phase changes in a two-phase closed thermosyphon (TPCT) enables a significant reduction in the heat generated even at high temperatures. In this paper, we propose a modification of the evaporation–condensation model implemented in ANSYS Fluent. The modification was to manipulate the value of the mass transfer time relaxation parameter for evaporation and condensation. The developed model in the form of a UDF script allowed the introduction of additional source equations, and the obtained solution is compared with the results available in the literature. The variable value of the mass transfer time relaxation parameter during condensation rc depending on the density of the liquid and vapour phase was taken into account in the calculations. However, compared to previous numerical studies, more accurate modelling of the phase change phenomenon of the medium in the thermosyphon was possible by adopting a mass transfer time relaxation parameter during evaporation re = 1. The assumption of ten-fold higher values resulted in overestimated temperature values in all sections of the thermosyphon. Hence, the coefficient re should be selected individually depending on the case under study. A too large value may cause difficulties in obtaining the convergence of solutions, which, in the case of numerical grids with many elements (especially three-dimensional), significantly increases the computation time.

A Pumped Two-Phase Cooling System for Spacecraft

1983 ◽  
Author(s):  
S. Ollendorf ◽  
F. A. Costello
Keyword(s):  
Cooling System ◽  
Two Phase ◽  
Two Phase Cooling

Model Predictive Control of a Pumped Two-Phase Cooling System With Microchannel Heat Exchangers

2018 ◽  
Author(s):  
Oyuna Angatkina ◽  
Andrew Alleyne
Keyword(s):  
Heat Flux ◽  
Model Predictive Control ◽  
Predictive Control ◽  
Heat Exchangers ◽  
Cooling System ◽  
High Heat ◽  
High Heat Flux ◽  
Two Phase ◽  
Cooling Systems ◽  
Two Phase Cooling

Two-phase cooling systems provide a viable technology for high–heat flux rejection in electronic systems. They provide high cooling capacity and uniform surface temperature. However, a major restriction of their application is the critical heat flux condition (CHF). This work presents model predictive control (MPC) design for CHF avoidance in two-phase pump driven cooling systems. The system under study includes multiple microchannel heat exchangers in series. The MPC controller performance is compared to the performance of a baseline PI controller. Simulation results show that while both controllers are able to maintain the two-phase cooling system below CHF, MPC has significant reduction in power consumption compared to the baseline controller.

Sign in / Sign up

Export Citation Format

Share Document