A high-order reduced Navier Stokes approximation for accurate mean flow calculation

1997 ◽  
Author(s):  
Michael Stanek ◽  
Stanley Rubin ◽  
Michael Stanek ◽  
Stanley Rubin
Keyword(s):  
High Order ◽  
Navier Stokes ◽  
Mean Flow ◽  
Flow Calculation ◽  
Stokes Approximation

Rotational and Quasiviscous Cold Flow Models for Axisymmetric Hybrid Propellant Chambers

2010 ◽  
Vol 132 (10) ◽  
Author(s):  
Joseph Majdalani ◽  
Michel Akiki
Keyword(s):  
Rocket Engine ◽  
Navier Stokes ◽  
Mathematical Treatment ◽  
Hybrid Rocket ◽  
Mean Flow ◽  
Viscous Effects ◽  
Navier Stokes Equation ◽  
Flow Models ◽  
Hybrid Rocket Engine ◽  
Wall Injection

In this work, we present two simple mean flow solutions that mimic the bulk gas motion inside a full-length, cylindrical hybrid rocket engine. Two distinct methods are used. The first is based on steady, axisymmetric, rotational, and incompressible flow conditions. It leads to an Eulerian solution that observes the normal sidewall mass injection condition while assuming a sinusoidal injection profile at the head end wall. The second approach constitutes a slight improvement over the first in its inclusion of viscous effects. At the outset, a first order viscous approximation is constructed using regular perturbations in the reciprocal of the wall injection Reynolds number. The asymptotic approximation is derived from a general similarity reduced Navier–Stokes equation for a viscous tube with regressing porous walls. It is then compared and shown to agree remarkably well with two existing solutions. The resulting formulations enable us to model the streamtubes observed in conventional hybrid engines in which the parallel motion of gaseous oxidizer is coupled with the cross-streamwise (i.e., sidewall) addition of solid fuel. Furthermore, estimates for pressure, velocity, and vorticity distributions in the simulated engine are provided in closed form. Our idealized hybrid engine is modeled as a porous circular-port chamber with head end injection. The mathematical treatment is based on a standard similarity approach that is tailored to permit sinusoidal injection at the head end.

Simulation of the Transitional Flow in a Low Pressure Gas Turbine Cascade With a High-Order Discontinuous Galerkin Method

2013 ◽  
Vol 135 (7) ◽  
Author(s):  
A. Ghidoni ◽  
A. Colombo ◽  
S. Rebay ◽  
F. Bassi
Keyword(s):  
Discontinuous Galerkin ◽  
Turbulence Model ◽  
Stokes Equations ◽  
Time Integration ◽  
High Order ◽  
Transitional Flow ◽  
Navier Stokes ◽  
Implicit Time ◽  
Turbine Cascade ◽  
High Reynolds

In the last decade, discontinuous Galerkin (DG) methods have been the subject of extensive research efforts because of their excellent performance in the high-order accurate discretization of advection-diffusion problems on general unstructured grids, and are nowadays finding use in several different applications. In this paper, the potential offered by a high-order accurate DG space discretization method with implicit time integration for the solution of the Reynolds-averaged Navier–Stokes equations coupled with the k-ω turbulence model is investigated in the numerical simulation of the turbulent flow through the well-known T106A turbine cascade. The numerical results demonstrate that, by exploiting high order accurate DG schemes, it is possible to compute accurate simulations of this flow on very coarse grids, with both the high-Reynolds and low-Reynolds number versions of the k-ω turbulence model.

Spatial Stability Analysis of a Flap Side Edge Vortex

2005 ◽  
Vol 4 (1-2) ◽  
pp. 37-47
Author(s):  
Jean-Philippe Brazier ◽  
Frédéric Moens ◽  
Philippe Bardoux
Keyword(s):  
Stability Analysis ◽  
Temporal Stability ◽  
Low Frequency ◽  
Aerodynamic Noise ◽  
Navier Stokes ◽  
Mean Flow ◽  
Side Edge ◽  
Amplification Rate ◽  
Edge Vortex ◽  
Flap Deflection

The flap side edge vortex is suspected to contribute to aerodynamic noise generation. Using a temporal stability analysis, Khorrami and Singer have shown that unstable modes could exist in this vortex. Due to the convective nature of this instability, a spatial analysis is more suitable. This is the subject of the present work. The mean flow past a 2D wing with a half-span flap has been computed with a steady 3D Navier-Stokes code. Then, local linear stability calculations are performed in several planes perpendicular to the vortex axis. The vortex is assumed axisymmetric and modelled with Batchelor's analytical vortex. Using Gaster's relation, the spatial amplification rate is calculated, giving by integration the relative amplitude of the fluctuations. Some low-frequency fluctuations are seen to be preferentially amplified by the vortex, but the amplifications remain small, so that this mechanism alone should not produce important noise in this particular configuration, where the flap deflection angle is moderate.

scholarly journals Modeling the 3-d flow around a cylinder using the SAS hybrid model

2014 ◽  
Vol 16 (5) ◽  
pp. 901-918 ◽  
Keyword(s):  
Turbulence Modeling ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Cross Flow ◽  
Numerical Code ◽  
Navier Stokes ◽  
Computational Domain ◽  
Mean Flow ◽  
Unstable Flow ◽  
Vortex Size

<div> <p>Three-dimensional calculations were performed to simulate the flow around a cylindrical vegetation element using the Scale Adaptive Simulation (SAS) model; commonly, this is the first step of the modeling of the flow through multiple vegetation elements. SAS solves the Reynolds Averaged Navier-Stokes equations in stable flow regions, while in regions with unstable flow it goes unsteady producing a resolved turbulent spectrum after reducing eddy viscosity according to the locally resolved vortex size represented by the von Karman length scale. A finite volume numerical code was used for the spatial discretisation of the rectangular computational domain with stream-wise, cross-flow and vertical dimensions equal to 30D, 11D and 1D, respectively, which was resolved with unstructured grids. Calculations were compared with experiments and Large Eddy Simulations (LES). Predicted overall flow parameters and mean flow velocities exhibited a very satisfactory agreement with experiments and LES, while the agreement of predicted turbulent stresses was satisfactory. Calculations showed that SAS is an efficient and relatively fast turbulence modeling approach, especially in relevant practical problems, in which the very high accuracy that can be achieved by LES at the expense of large computational times is not required.</p> </div> <p>&nbsp;</p>

Sign in / Sign up

Export Citation Format

Share Document