Instantaneous Three-Dimensional Vorticity Measurements in Vortical Flow over a Delta Wing

AIAA Journal ◽  
10.2514/2.20 ◽  
1997 ◽  
Vol 35 (10) ◽  
pp. 1612-1620 ◽  
Author(s):  
A. Honkan ◽  
J. Andreopoulos
Keyword(s):  
Delta Wing ◽  
Three Dimensional ◽  
Vortical Flow

Instantaneous three-dimensional vorticity measurements in vortical flow over a delta wing

AIAA Journal ◽  
1997 ◽  
Vol 35 ◽  
pp. 1612-1620
Author(s):  
A. Honkan ◽  
J. Andreopoulos
Keyword(s):  
Delta Wing ◽  
Three Dimensional ◽  
Vortical Flow

Numerical Investigations for the Effect of Slender Body on Dynamic Rolling Characteristics of a 80°/60° Double Delta Wing

2013 ◽  
Vol 444-445 ◽  
pp. 286-292
Author(s):  
Bing Han ◽  
Min Xu ◽  
Xi Pei ◽  
Xiao Min An
Keyword(s):  
Stokes Equations ◽  
Delta Wing ◽  
Time Lag ◽  
Slender Body ◽  
Vortical Flow ◽  
Navier Stokes ◽  
Rolling Motion ◽  
Navier Stokes Equations ◽  
Lag Effect ◽  
Double Delta Wing

The effect of slender body on the rolling characteristics of a double delta wing is found by comparing the numerical simulation results of the double delta wing and wing-body configuration. The coupled computation system solving the Navier-Stokes equations and the rolling motion equation alternatively to obtain the unsteady vortical flow around the two configurations while rolling. The results conclusively showed the upwash effect of the slender body enhanced the energy of strake vortex and merged vortex.The aerodynamic lag of double delta wing is weak, contrarily, the time lag effect of the wing-body configuration is significant. The asymmetry vortices structure nearby the trailing edge are believed to be the main reason for the unsteady time lag effect.

Boundary-Layer Flow Between the Attachment Lines on a Flat Plate Delta Wing at Incidence

1962 ◽  
Vol 13 (1) ◽  
pp. 1-16
Author(s):  
J. C. Cooke
Keyword(s):  
Boundary Layer ◽  
Delta Wing ◽  
Three Dimensional ◽  
External Flow ◽  
Two Dimensional ◽  
Conical Flow ◽  
Slender Body Theory ◽  
Layer Flow ◽  
Body Theory ◽  
Transition Fronts

SummaryA three-dimensional laminar-boundary-layer calculation is carried out over the area concerned. The external flow is simplified, being calculated by slender-body theory assuming conical flow, with two point vortices above the wing, their positions and strength being determined by experiment. Attempts are made to draw transition fronts both for two-dimensional and sweep instability from this calculation. The combination of these gives fronts similar to those observed in some experiments. Because there is little or no pressure gradient over the area in question it is suggested that it is a region where distributed suction might usefully be applied in order to maintain laminar flow and reduce drag.

Novel Turbine Endwall Contours for the Reduction of Heat Transfer Generated Using the Ice Formation Method

2012 ◽  
Author(s):  
Kristian Haase ◽  
Sven Winkler ◽  
Bernhard Weigand ◽  
Sven Olaf Neumann
Keyword(s):  
Heat Transfer ◽  
Guide Vane ◽  
Three Dimensional ◽  
Vortical Flow ◽  
Ice Formation ◽  
The Novel ◽  
Average Heat ◽  
Low Pressure Turbine ◽  
Transfer Behavior ◽  
Formation Method

Three-dimensional contouring of vane endwalls has proven to be an efficient method for reducing aerodynamic losses or, respectively, endwall heat transfer by active manipulation of the complex vortical flow structures in the vane passage. The present study shows the application of the Ice Formation Method for endwall contouring of a guide vane row with the goal of reducing endwall heat transfer. Endwall contours for the guide vane row of a low pressure turbine are experimentally generated in form of ice contours and evaluated with respect to their heat transfer behavior. A comparison with the flat plate showed that average heat transfer is considerably reduced for the ice-contoured endwalls with reductions up to 42%. The generated endwall contours were also digitized and used in numerical simulations. The latter allowed for a comparison of endwall heat transfer for the novel contours with the heat transfer for a flat, uncontoured endwall. This showed that the new endwall contours also feature decreased average heat transfer compared to the flat endwall with the maximum obtained reduction being 12%.

Flow/Acoustic Mechanisms in Three-Dimensional Vortices Undergoing Sinusoidal-Wave Instabilities

2007 ◽  
Author(s):  
Wenhua Li ◽  
Z. C. Zheng ◽  
Ying Xu
Keyword(s):  
Flow Field ◽  
Three Dimensional ◽  
Vortex Pair ◽  
Particle Method ◽  
Acoustic Signals ◽  
Short Wave ◽  
Vortical Flow ◽  
Vortex Particle Method ◽  
Structure Changes ◽  
Wave Instabilities

It has been identified that vorticity in a vortex core directly relates to the frequency of a significant sound peak from an aircraft wake vortex pair where each of the vortices is modeled as an elliptic core Kirchhoff vortex. In three-dimensional vortices, sinusoidal instabilities at various length scales result in significant flow structure changes in these vortices, and thus influence their radiated acoustic signals. In this study, a three-dimensional vortex particle method is used to simulate the incompressible vortical flow. The flow field, in the form of vorticity, is employed as the source in the far-field acoustic calculation using a vortex sound formula that enables computation of acoustic signals radiated from an approximated incompressible flow field. Cases of vortex rings and a pair of counter-rotating vortices are studied when they are undergoing both long- and short-wave instabilities. Both inviscid and viscous interactions are considered and effects of turbulence are simulated using sub-grid-scale models.

Sign in / Sign up

Export Citation Format

Share Document