scholarly journals Effects of Methyl Acetate as Oxygenated Fuel Blending on Performance and Emissions of SI Engine

2018 ◽  
Vol 22 (1) ◽  
pp. 55-68 ◽  
Author(s):  
Abdulvahap Cakmak ◽  
Murat Kapusuz ◽  
Orkhan Ganiyev ◽  
Hakan Ozcan
Keyword(s):  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Methyl Acetate ◽  
Engine Performance ◽  
Specific Fuel Consumption ◽  
Brake Specific Fuel Consumption ◽  
Si Engine ◽  
Brake Thermal Efficiency ◽  
Oxygenated Fuel ◽  
Fuel Blending

Abstract - The objective of this paper is to investigate the use of methyl acetate as oxygenated fuel blending for base gasoline in SI engine. The effects of methyl acetate on engine performance parameters (brake specific fuel consumption, brake thermal efficiency and energy consumption rate) and exhaust emissions (CO, HC, CO2 and NOx) of SI engine have been experimentally investigated. Engine experiments were conducted on a single cylinder, water cooled, spark-ignition test engine at constant moderate speed; 1500 rpm for different loads; 104, 207, 311 and 414 kPa fuelling the engine with base gasoline, M5 (95 % base gasoline +5 % methyl acetate) and M10 (90 % base gasoline +10 % methyl acetate). The results showed that adding methyl acetate to base gasoline increases the brake specific fuel consumption while reducing the brake thermal efficiency of the engine. Furthermore, it was also observed that methyl acetate addition does not have a great effect on HC emissions, however, reduces CO and increases CO2 emissions. NOx results showed a striking increase in the level of NOx emissions with the addition of methyl acetate.

scholarly journals The experimental investigation of diesel fuel-biofuel blends at different injection pressures in a DI diesel engine

2021 ◽  
Vol 9 (4A) ◽  
Author(s):  
İlker Örs ◽  
◽  
Murat Ciniviz ◽  
Bahar Sayin Kul ◽  
Ali Kahraman ◽  
...  
Keyword(s):  
Fuel Consumption ◽  
Diesel Fuel ◽  
Thermal Efficiency ◽  
Engine Performance ◽  
Injection Pressure ◽  
Exhaust Emissions ◽  
Specific Fuel Consumption ◽  
Brake Specific Fuel Consumption ◽  
Brake Thermal Efficiency ◽  
Injection Pressures

In this study, it was aimed to investigate the effects of a diesel-biodiesel blend (B20) and a diesel-biodiesel-bioethanol blend (BE5) on combustion parameters in addition to engine performance and exhaust emissions compared with diesel fuel. Parameters included in the evaluation was brake specific fuel consumption, brake thermal efficiency, CO, CO2, HC, NOx, smoke opacity emissions and finally cylinder pressure, heat release rate, ignition delay, some key points of the combustion phases such as start of ignition, start of combustion, CA50 and CA90 and combustion duration. Engine tests were conducted at different injection pressures of 170 bar, 190 bar, which is the original injection pressure, and 220 bar by the engine being loaded by 25, 50, 75 and 100% for the assessment of engine performance and exhaust emissions. For combustion evaluation, the data obtained at 1400 rpm, maximum torque-speed, and 2800 rpm, maximum power-speed were used, while the injection pressures were set to 170, 190 and 220 bar under full load condition. According to test results, the better performance characteristics, exhaust emissions and combustion behaviour of engine were obtained with the use of BE5 at high injection pressure. So, BE5 fuel improved brake specific fuel consumption by about 7% and brake thermal efficiency by about 6% compared to B20. In addition, while the emission values of BE5 gave better results than diesel fuel, it reduced the NOx and smoke emissions of B20 by approximately 1.4% and 6.4% respectively. Moreover, it has achieved a reduction in smoke emission of up to 45% compared to diesel fuel.

scholarly journals EXPERIMENTAL ANALYSIS OF THE COMBUSTION CHAMBER COATED WITH Mo AND Al2O3-TiO2 IN A DIESEL ENGINE

2021 ◽  
Vol 55 (4) ◽  
Author(s):  
Murugan Kuppusamy ◽  
Thirumalai Ramanathan ◽  
Udhayakumar Krishnavel ◽  
Seenivasan Murugesan
Keyword(s):  
Combustion Chamber ◽  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Performance Test ◽  
Ceramic Powder ◽  
Specific Fuel Consumption ◽  
Emission Characteristic ◽  
Powder Materials ◽  
Brake Specific Fuel Consumption ◽  
Brake Thermal Efficiency

The effect of thermal-barrier coatings (TBCs) reduces fuel consumption, effectively improving the engine efficiency. This research focused on a TBC with a thickness of 300 µm insulating the combustion chamber of a direct ignition (DI) engine. The piston crown, inlet and exhaust-valve head were coated using air-plasma-spray coating. Ceramic powder materials such as molybdenum (Mo) and aluminum oxide titanium dioxide (Al2O3-TiO2) were used. A performance test of the engine with the coated combustion chamber was carried out to investigate the brake power, brake thermal efficiency, volumetric efficiency, brake specific fuel consumption and air-fuel ratio. Also, an emission-characteristic test was carried out to investigate the emissions of unburned hydrocarbon (HC), carbon monoxide (CO), nitrogen oxides (NO, NO2, NO3) and smoke opacity (SO). The results reveal that the brake thermal efficiency and brake specific fuel consumption show significant increases because of these coating materials. The effect of the Al2O3-TiO2 coating significantly reduces the HC and CO engine emissions.

The Comparative Trail Research on the Performance of a Diesel Engine Fuelled with Diesel Fuel and Biodiesel/Diesel Blended Fuel

2011 ◽  
Vol 142 ◽  
pp. 103-106
Author(s):  
Wen Ming Cheng ◽  
Hui Xie ◽  
Gang Li
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Diesel Fuel ◽  
Thermal Efficiency ◽  
Specific Fuel Consumption ◽  
Brake Specific Fuel Consumption ◽  
Brake Thermal Efficiency ◽  
Series Of Experiments ◽  
Blended Fuel ◽  
Load Conditions

This paper discusses the brake specific fuel consumption and brake thermal efficiency of a diesel engine using cottonseed biodiesel blended with diesel fuel. A series of experiments were conducted for the various blends under varying load conditions at a speed of 1500 rpm and 2500 rpm and the results were compared with the neat diesel. From the results, it is found that the brake specific fuel consumption of cottonseed biodiesel is slightly higher than that of diesel fuel at different engine loads and speeds, with this increase being higher the higher the percentage of the biodiesel in the blend. And the brake thermal efficiency of cottonseed biodiesel is nearly similar to that of diesel fuel at different engine loads and speeds. From the investigation, it is concluded that cottonseed biodiesl can be directly used in diesel engines without any modifications, at least in small blending ratios.

scholarly journals An Assessment on Performance Characteristics of Diesel Engine Using Lemongrass-Diesel Oil Fuel Blends

2021 ◽  
Author(s):  
Naveen Rana ◽  
Harikrishna Nagwan ◽  
Kannan Manickam
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Diesel Fuel ◽  
Thermal Efficiency ◽  
Specific Fuel Consumption ◽  
Performance Characteristics ◽  
Emission Characteristics ◽  
Brake Specific Fuel Consumption ◽  
Brake Thermal Efficiency ◽  
Fuel Blends

Abstract Indeed, the development of alternative fuels for use in internal combustion engines has become an essential requirement to meet the energy demand and to deal with the different problems related to fuel. The research in this domain leads to the identification of adverse fuel properties and for their solution standard limits are being defined. This paper outlines an investigation of performance and combustion characteristics of a 4-stroke diesel engine using different cymbopogon (lemongrass) - diesel fuel blends. 10% to 40% cymbopogon is mixed with diesel fuel and tested for performance characteristics like brake specific fuel consumption and brake thermal efficiency. To obtain emission characteristics smoke density in the terms of HSU has been measured. In result, it has observed that there is an increase of 5% in brake thermal efficiency and 16.33% decrease in brake specific fuel consumption. Regarding emission characteristics, a 12.9% decrease in smoke emission has been found.

Experimental Investigation of SI Engine Performance Using Oxygenated Fuel

2002 ◽  
Author(s):  
Abdulghani A. Al-Farayedhi ◽  
Ali M. Al-Dawood ◽  
P. Gandhidasan
Keyword(s):  
Thermal Efficiency ◽  
Engine Performance ◽  
Operating Conditions ◽  
Maximum Output ◽  
Si Engine ◽  
Brake Thermal Efficiency ◽  
Oxygenated Fuel ◽  
Ethanol Blends ◽  
Set Up ◽  
Better Than

The current experimental study aims to examine the effects of using oxygenates as a replacement of lead additives in gasoline on performance of a typical SI engine. The tested oxygenates are MTBE, methanol, and ethanol. These oxygenates were blended with a base unleaded fuel in three ratios (10, 15, and 20 vol.%). The engine maximum output and thermal efficiency were evaluated at a variety of engine operating conditions using an engine dynamometer set-up. The results of the oxygenated blends were compared to those of the base fuel and of a leaded fuel prepared by adding TEL to the base. When compared to the base and leaded fuels, the oxygenated blends improved the engine brake thermal efficiency. The leaded fuel performed better than the oxygenated blends in terms of the maximum output of the engine except in the case of 20 vol.% methanol and 15 vol.% ethanol blends. Overall, the methanol blends performed better than the other oxygenated blends in terms of engine output and thermal efficiency.

Turbocharged spark-ignition engine performance prediction in various inlet charged air temperatures fueled with gasoline–ethanol blends

2020 ◽  
pp. 146808742093171
Author(s):  
Reza Farzam ◽  
Bahram Jafari ◽  
Fateme Kalaki
Keyword(s):  
Fuel Consumption ◽  
Air Temperature ◽  
Thermal Efficiency ◽  
Engine Performance ◽  
Spark Ignition Engine ◽  
Specific Fuel Consumption ◽  
Brake Specific Fuel Consumption ◽  
Brake Torque ◽  
Combustion Duration ◽  
And Performance

In this research, the effect of alternative fuels and the inlet charged air temperature is numerically investigated on the performance of a turbocharged spark-ignition engine. For this purpose, a one-dimensional engine and turbocharger model is created in an engine simulation and performance analysis software and validated with former experimental results. Then, the model is run with four fuel types, including two gasoline types with different octane numbers and two ethanol–gasoline blend fuels—E25 and E85. In each case, the inlet charged air temperature is changed from cold to hot condition and performance characteristics such as the spark advance timing, brake torque, brake-specific fuel consumption and thermal efficiency, emissions and the ignition delay and combustion duration are obtained from simulation results. The results illustrate that by decreasing the inlet charged air temperature, the spark timing is more advanced due to less knock and the brake torque increases. Also, the brake-specific fuel consumption and the brake NOx and CO2 decrease and thermal efficiency increases in all fuel types. The results also demonstrate that in higher ethanol percent in blend fuels, all engine performance characteristics improve except brake-specific fuel consumption; as changing the fuel at constant fuel-to-air equivalence ratio from E25 to E85 in various revolutions per minute causes a 5.8% increase in the brake torque, 1.06% increase in the thermal efficiency, 43% and 3.9% decrease in the brake NOx and CO2 and 5.8 °CA decrease in the combustion duration, on average; while the brake-specific fuel consumption and the peak pressure increase 29% and 20%, respectively.

scholarly journals Performance and Emission Characteristics of a Four Stroke Spark Ignition Engine with Recirculation of Hot and Cold Exhaust Gases

2018 ◽  
Vol 7 (4.5) ◽  
pp. 405
Author(s):  
Aritra Ganguly ◽  
Baidya Nath Murmu ◽  
Somnath Chakrabarti
Keyword(s):  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Specific Fuel Consumption ◽  
Intake Manifold ◽  
Emission Characteristics ◽  
Exhaust Gas ◽  
Brake Specific Fuel Consumption ◽  
Brake Thermal Efficiency

An experiment has been conducted on a four-stroke, four-cylinder spark ignition engine with and without recirculation of exhaust gas for different loads at a constant speed. Two cases were considered, the first in which 10% and later 20% of the exhaust gas was directly supplied to the intake manifold at a temperature of 820°C, while in the second case the same proportions of exhaust gas were cooled in a heat-exchanger to a temperature of 210°C before supply. Engine performance parameters like brake specific fuel consumption, brake thermal efficiency were evaluated under those conditions and compared with the same engine operating without recirculation. The corresponding emission characteristics of the engine were also measured using an exhaust gas analyzer which measured the amount of NOx, CO, CO2 and un-burnt HC. The performance and emissions characteristics of the engine obtained with hot and cold EGR were compared with reference to the same engine operating without EGR. The study revealed that the performance of the engine was better in terms of brake thermal efficiency and brake specific fuel consumption with cold EGR compared to hot EGR. However, the emissions of CO and HC were higher with cold EGR compared to that of hot EGR.   

Experimental Investigation of SI Engine Performance Using Oxygenated Fuel

2004 ◽  
Vol 126 (1) ◽  
pp. 178-191 ◽  
Author(s):  
A. A. Al-Farayedhi ◽  
A. M. Al-Dawood ◽  
P. Gandhidasan
Keyword(s):  
Thermal Efficiency ◽  
Engine Performance ◽  
Operating Conditions ◽  
The Other ◽  
Maximum Output ◽  
Si Engine ◽  
Brake Thermal Efficiency ◽  
Oxygenated Fuel ◽  
Ethanol Blends ◽  
Better Than

The current experimental study aims to examine the effects of using oxygenates as a replacement of lead additives in gasoline on performance of a typical SI engine. The tested oxygenates are MTBE, methanol, and ethanol. These oxygenates were blended with a base unleaded fuel in three ratios (10, 15, and 20 vol.%). The engine maximum output and thermal efficiency were evaluated at a variety of engine operating conditions using an engine dynamometer setup. The results of the oxygenated blends were compared to those of the base fuel and of a leaded fuel prepared by adding TEL to the base. When compared to the base and leaded fuels, the oxygenated blends improved the engine brake thermal efficiency. The leaded fuel performed better than the oxygenated blends in terms of the maximum output of the engine except in the case of 20 vol.% methanol and 15 vol.% ethanol blends. Overall, the methanol blends performed better than the other oxygenated blends in terms of engine output and thermal efficiency.

Characteristics of Water-in-Diesel Emulsions in a Single Cylinder Compression Ignition Engine

2014 ◽  
Author(s):  
Teja Gonguntla ◽  
Robert Raine ◽  
Leigh Ramsey ◽  
Thomas Houlihan
Keyword(s):  
Fuel Consumption ◽  
Direct Injection ◽  
Engine Performance ◽  
Operating Conditions ◽  
Specific Fuel Consumption ◽  
Brake Specific Fuel Consumption ◽  
Compression Ignition Engine ◽  
Oil Emulsion ◽  
Single Cylinder ◽  
Performance And Emission

The objective of this project was to develop both engine performance and emission profiles for two test fuels — a 6% water-in-diesel oil emulsion (DOE-6) fuel and a neat diesel (D100) fuel. The testing was performed on a single cylinder, direct-injection, water-cooled diesel engine coupled to an eddy current dynamometer. Output parameters of the engine were used to calculate Brake Specific Fuel Consumption (BSFC) and Engine Efficiency (η) for each test fuel. DOE-6 fuels generated a 24% reduction in NOX and a 42% reduction in Carbon Monoxide emissions over the tested operating conditions. DOE-6 fuels presented higher ignition delays — between 1°-4°, yielded 1%–12% lower peak cylinder pressures and produced up to 5.5% lower exhaust temperatures. Brake Specific Fuel consumption increased by 6.6% for the DOE-6 fuels as compared to the D100 fuels. This project is the first research done by a New Zealand academic institution on water-in-diesel emulsion fuels.

scholarly journals Control of Exhaust Emissions Using Piston Coating on Two-StrokeSI Engines with Gasoline Blends

2021 ◽  
Vol 8 (1) ◽  
pp. H16-H20
Author(s):  
A.V.N.S. Kiran ◽  
B. Ramanjaneyulu ◽  
M. Lokanath M. ◽  
S. Nagendra ◽  
G.E. Balachander
Keyword(s):  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Internal Combustion Engines ◽  
Fossil Fuels ◽  
Engine Performance ◽  
Exhaust Emissions ◽  
Specific Fuel Consumption ◽  
Thermal Barrier ◽  
Piston Crown ◽  
Barrier Coating

An increase in fuel utilization to internal combustion engines, variation in gasoline price, reduction of the fossil fuels and natural resources, needs less carbon content in fuel to find an alternative fuel. This paper presents a comparative study of various gasoline blends in a single-cylinder two-stroke SI engine. The present experimental investigation with gasoline blends of butanol and propanol and magnesium partially stabilized zirconium (Mg-PSZ) as thermal barrier coating on piston crown of 100 µm. The samples of gasoline blends were blended with petrol in 1:4 ratios: 20 % of butanol and 80 % of gasoline; 20 % of propanol and 80 % of gasoline. In this work, the following engine characteristics of brake thermal efficiency (BTH), specific fuel consumption (SFC), HC, and CO emissions were measured for both coated and non-coated pistons. Experiments have shown that the thermal efficiency is increased by 2.2 % at P20. The specific fuel consumption is minimized by 2.2 % at P20. Exhaust emissions are minimized by 2.0 % of HC and 2.4 % of CO at B20. The results strongly indicate that the combination of thermal barrier coatings and gasoline blends can improve engine performance and reduce exhaust emissions.

Sign in / Sign up

Export Citation Format

Share Document