scholarly journals Beam Bond Tests of GFRP and Steel Reinforcement to Concrete

2018 ◽  
Vol 64 (4) ◽  
pp. 243-256
Author(s):  
D. Szczech ◽  
R. Kotynia
Keyword(s):  
Reinforced Concrete ◽  
Surface Preparation ◽  
Steel Reinforcement ◽  
Experimental Program ◽  
Bond Behaviour ◽  
Gfrp Bars ◽  
Concrete Members ◽  
Glass Fiber Reinforced ◽  
Steel Bars ◽  
Frp Bars

AbstractThe paper presents research program of bond between glass fiber reinforced polymer bars and concrete in reference to the steel bars. Bond between the reinforcement and concrete is a crucial parameter governing a behaviour of reinforced concrete members and transferring of the internal forces from concrete to the reinforcement. The use of FRP bars as an equivalent reinforcement to steel in concrete structures has increased in recent years. The FRP bars are very different from steel, mainly due to much lower elasticity modulus and their anisotropic structure. Good performance of FRP reinforced concrete requires sufficient interfacial bond between bars and concrete. However, there are no specific standards referring to the surface preparation of these bars, that leads to variable bond behaviour of the composite reinforcement to the concrete. The objective of the study was to investigate the influence of variable parameters on the bond behaviour to concrete. The experimental program consisted of eighteen beam bond specimens varying in: bar diameter (12mm, 16mm, 18mm) and type of reinforcement (GFRP sand – coated and steel bars). Although the GFRP bars indicated good bond behaviour to concrete, the average bond strength was slightly lower than that of steel reinforcement of 16mm and 18 mm, while it was higher for the GFRP bars of 12mm diameter.

Minimum thickness of concrete members reinforced with fibre reinforced polymer bars

2001 ◽  
Vol 28 (4) ◽  
pp. 583-592 ◽  
Author(s):  
Amin Ghali ◽  
Tara Hall ◽  
William Bobey
Keyword(s):  
Reinforced Concrete ◽  
Minimum Thickness ◽  
Reinforced Polymers ◽  
Flexural Members ◽  
Steel Reinforced Concrete ◽  
Concrete Members ◽  
Reinforced Polymer ◽  
Steel Bars ◽  
Fibre Reinforced Polymer ◽  
Frp Bars

To avoid excessive deflection most design codes specify the ratio (l/h)s, the span to minimum thickness of concrete members without prestressing. Use of the values of (l/h)s specified by the codes, in selecting the thickness of members, usually yields satisfactory results when the members are reinforced with steel bars. Fibre reinforced polymer (FRP) bars have an elastic modulus lower than that of steel. As a result, the values of (l/h)s specified in codes for steel-reinforced concrete would lead to excessive deflection if adopted for FRP-reinforced concrete. In this paper, an equation is developed giving the ratio (l/h)f for use with FRP bars in terms of (l/h)s and (εs/εf), where εs and εf are the maximum strain allowed at service in steel and FRP bars, respectively. To control the width of cracks, ACI 318-99 specifies εs = 1200 × 10–6 for steel bars having a modulus of elasticity, Es, of 200 GPa and a yield strength, fy, of 400 MPa. At present, there is no value specified for εf; a value is recommended in this paper.Key words: concrete, cracking, deflection, fibre reinforced polymers, flexural members, minimum thickness.

scholarly journals Preparation and characterization of glass fibers – polymers (epoxy) bars (GFRP) reinforced concrete for structural applications

2016 ◽  
Vol 11 (1) ◽  
pp. 15-22
Author(s):  
Saeed Alkjk ◽  
Rafee Jabra ◽  
Salem Alkhater
Keyword(s):  
Tensile Strength ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Glass Fibers ◽  
Reinforce Concrete ◽  
Experimental Program ◽  
Gfrp Bars ◽  
Structural Applications ◽  
Steel Bars ◽  
Deflection Test

Abstract The paper presents some of the results from a large experimental program undertaken at the Department of Civil Engineering of Damascus University. The project aims to study the ability to reinforce and strengthen the concrete by bars from Epoxy polymer reinforced with glass fibers (GFRP) and compared with reinforce concrete by steel bars in terms of mechanical properties. Five diameters of GFRP bars, and steel bars (4mm, 6mm, 8mm, 10mm, 12mm) tested on tensile strength tests. The test shown that GFRP bars need tensile strength more than steel bars. The concrete beams measuring (15cm wide × 15cm deep × and 70cm long) reinforced by GFRP with 0.5 vol.% ratio, then the concrete beams reinforced by steel with 0.89 vol.% ratio. The concrete beams tested on deflection test. The test shown that beams which reinforced by GFRP has higher deflection resistance, than beams which reinforced by steel. Which give more advantage to reinforced concrete by GFRP.

Flexural Behaviour of Reinforced Concrete Beam with Glass Fiber Reinforced Polymer (GFRP) Bar Strengthened with Carbon Fiber Reinforced Polymer (CFRP) Plate

2014 ◽  
Vol 1051 ◽  
pp. 748-751 ◽  
Author(s):  
Norhafizah Salleh ◽  
Abdul Rahman Mohd Sam ◽  
Jamaludin Mohd Yatim ◽  
Mohd. Firdaus bin Osman
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Reinforced Concrete Beam ◽  
Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Gfrp Bars ◽  
Reinforced Polymer ◽  
Cfrp Plate ◽  
Glass Fiber Reinforced ◽  
Steel Bars

The use of glass-fiber-reinforced polymer (GFRP) bar to replace steel reinforcement in concrete structures is a relatively a new technique. The GFRP bars possess mechanical properties different from steel bars, including high tensile strength combined with low elastic modulus and linear stress–strain relationship up to failure. Therefore, design procedures and process should account for these properties. This paper presents the experimental work on the flexural behavior of concrete beam reinforced with GFRP bars and strengthen with CFRP plate. A total of ten reinforced concrete beams reinforced with either steel and GFRP bars were cast and tested under four point loads. Eight concrete beams (200x250x2800mm) were reinforced with 13mm diameter GFRP bars together with strengthening using CFRP plate and two control beams reinforced with 12mm diameter steel bars were tested. The experimental results show that although the stiffness of the beams reduced but the ultimate load of the GFRP reinforced concrete beam is bigger than steel reinforced beam. It was also found that strengthening using CFRP plate will further enhanced the flexural performance of the beams with GFRP bars.

scholarly journals Bending reinforced concrete beams with glass fiber reinforced polymer bars: an experimental analysis

2021 ◽  
Vol 14 (3) ◽  
Author(s):  
Tales Viebrantz Fernandes ◽  
Aline Ribeiro Paliga ◽  
Charlei Marcelo Paliga
Keyword(s):  
Reinforced Concrete ◽  
Glass Fiber ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
Fiber Reinforced Polymers ◽  
Fiber Reinforced ◽  
Cross Sectional ◽  
Gfrp Bars ◽  
Glass Fiber Reinforced ◽  
Steel Bars

abstract: There is a recurring need to construct in places where environmental aggressiveness is very high, such as tidal-splash sites, chemical industries, etc. In these places, steel bars, commonly used for concrete reinforcement, can suffer deterioration, losing cross-sectional area and consequently the resistant capacity. In this regard, Glass Fiber Reinforced Polymers (GFRP) bars can replace steel because of its high strength to harsh environments, low weight and high tensile strength. Thus, this work aimed to compare reinforced concrete beams with steel bars and GFRP bending bars using the procedures indicated in ABNT:NBR 6118 and ACI 440.1R-15, respectively. Experimental three-point flexural tests were performed on six concrete beams, three reinforced with steel bars and three reinforced with GFRP bars. The beams were designed for centered point loads of 23.5 kN, 37.5 kN and 57 kN, and for each load one beam was reinforced in steel and one in GFRP. As main conclusions, it can be said that the beams reinforced with GFRP bars presented greater transverse displacements due to the low modulus of elasticity of this material. In addition, the beams presented rupture loads close to each design load, showing agreement in the recommendations of the two normative documents. Comparing the maximum loads of steel and GFRP beams, ratios of +9.3%, -3.2% and -3% were obtained for beams designed for 23.5 kN, 37.5 kN and 57 kN, respectively. Also, that variations in design loads cause greater variation in the longitudinal reinforcement rate of GFRP bar-beams compared to steel-bar beams.

Analisa Pola Kegagalan Balok Beton Menggunakan GFRP Bar Tanpa Selimut Beton

2020 ◽  
Vol 24 (1) ◽  
pp. 11-16
Author(s):  
Saddam - Husein ◽  
Rudy Djamaluddin ◽  
Rita Irmawaty ◽  
Kusnadi Kusnadi
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Concrete Cover ◽  
Steel Reinforcement ◽  
Fiber Reinforced Polymer ◽  
Mode Analysis ◽  
Flexural Capacity ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced ◽  
Gfrp Bar

SADDAM HUSEIN. Analisa Pola Kegagalan Balok Beton Menggunakan GFRP Bar Tanpa Selimut Beton (dibimbing oleh Rudi Djamaluddin dan Rita Irmawaty) Struktur beton bertulang yang menggunakan tulangan baja pada daerah korosif, menjadi rawan terhadap kerusakan atau penurunan kekuatannya akibat korosi.Korosi pada tulangan baja merupakan salah satu faktor penyebab menurunnya kekuatan struktur beton bertulang. Salah satu material yang dikembangkan mengatasi korosi adalah penggunaan material tulangan GFRP (Glass Fiber Reinforced Polymer). Penelitian ini bertujuan untuk menganalisa kapasitas lentur dan pola kegagalan balok beton tanpa selimut dengan menggunakan material tulangan GFRP bar.   Desain penelitian merupakan eksperimental laboratorium dengan rekapitulasi sebanyak 6 sampel yang terdiri dari 2 Balok beton menggunakan tulangan baja dengan selimut beton, 2 balok beton menggunakan tulangan GFRP bar dengan selimut beton, 2 balok beton menggunakan GFRP bar tanpa selimut beton. Metode pengujian dilakukan dengan dengan pengujian lentur statik monotonik dan Analisis data menggunakan uji kondisi retak awal dan kondisi ultimit.   Hasil penelitian ini menunjukkan bahwa kapasitas lentur pada balok dengan tulangan GFRP bar lebih besar dibandingkan dengan balok tulangan baja dan mampu meningkatkan kapasitas lentur balok dalam menahan beban sebesar 39.76 %, pola kegagalan beton yang terjadi pada balok tulangan baja mengalami kegagalan lentur tekan ditandai dengan retakan yang terjadi pada sisi tertekan dan membentuk retakan tegak dengan sumbu netral beton yang tertekan, sedangkan pada balok beton tulangan GFRP tanpa selimut mengalami kegagalan keruntuhan tekan geser dengan kondisi tulangan berdeformasi (bi-linear) dengan retak miring dan secara tiba-tiba menjalar menuju sumbu netral beton yang tertekan sehingga terjadilah keruntuhan secara tiba-tiba.     SADDAM HUSEIN.Failure mode analysis of concrete Beams Using GFRP rebar Without concrete cover (supervised by Rudi Djamaluddin and Rita Irmawaty)   Reinforced concrete that uses rebar steel in corrosive areas, are prone to damage or decreased strength due to corrosion. Corrosion in the steel reinforcement is one of the factors that decreasing strength of reinforced concrete. One of the materials developed to overcome corrosion is the use of GFRP (Glass Fiber Reinforced Polymer) reinforcement material. This study aims to analyze the flexural capacity and failure mode of concrete beams without concrete cover using material GFRP bar as reinforcement.   The research design was an experimental laboratory with a recapitulation of 6 samples consisting of 2 beams using steel reinforcement with concrete cover.2 concrete beams using reinforcement GFRP bar with concrete cover, 2 beams using GFRP bars without concrete cover. The  research method uses the monotonic static flexure and analyzing the data using the initial crack condition and ultimate conditions test.   The results of the research indicate the flexural capacity of the beams with GFRP bar reinforcement is higher than steel reinforcement beams and can increase 39.76% of the flexural capacity of the beams in holding loads , the failure mode analysis occurs in steel reinforcing beam experiences compressive failure. Failure was characterized  by cracks that occur on the depressing side and form an upright crack with the neutral axis of the compressed concrete, whereas in GFRP reinforced concrete beams without concrete cover, failure of shear compression with conditions of deformed reinforcement (bi-linear) with sloping cracks and suddenly spread towards the neutral axis of the compressed concrete so that there was a sudden collapse.

scholarly journals Bond Behaviour of Near-Surface Mounted Strips in RC Beams—Experimental Investigation and Numerical Simulations

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4362
Author(s):  
Renata Kotynia ◽  
Hussien Abdel Baky ◽  
Kenneth W. Neale
Keyword(s):  
Concrete Strength ◽  
Element Model ◽  
Steel Reinforcement ◽  
Reinforcement Ratio ◽  
Experimental Program ◽  
Fe Model ◽  
Bond Behaviour ◽  
Near Surface ◽  
Cfrp Laminates ◽  
Near Surface Mounted

This paper presents an investigation of the bond mechanism between carbon fibre reinforced polymer (CFRP) laminates, concrete and steel in the near-surface mounted (NSM) CFRP-strengthened reinforced concrete (RC) beam-bond tests. The experimental program consisting of thirty modified concrete beams flexurally strengthened with NSM CFRP strips was published in. The effects of five parameters and their interactions on the ultimate load carrying capacities and the associated bond mechanisms of the beams are investigated in this paper with consideration of the following investigated parameters: beam span, beam depth, longitudinal tensile steel reinforcement ratio, the bond length of the CFRP strips and compressive concrete strength. The longitudinal steel reinforcement was cut at the beam mid-span in four beams to investigate a better assessment of the influence of the steel reinforcement ratio on the bond behaviour of CFRP to concrete bond behaviour. The numerical analysis implemented in this paper is based on a nonlinear micromechanical finite element model (FEM) that was used for investigation of the flexural behaviour of NSM CFRP-strengthened members. The 3D model based on advanced CFRP to concrete bond responses was introduced to modelling of tested specimens. The FEM procedure presents the orthotropic behaviour of the CFRP strips and the bond response between the CFRP and concrete. Comparison of the experimental and numerical results revealed an excellent agreement that confirms the suitability of the proposed FE model.

scholarly journals Numerical Sensing of Plastic Hinge Regions in Concrete Beams with Hybrid (FRP and Steel) Bars

Sensors ◽  
2018 ◽  
Vol 18 (10) ◽  
pp. 3255 ◽  
Author(s):  
Fang Yuan ◽  
Mengcheng Chen
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Plastic Hinge ◽  
Reinforcement Ratio ◽  
Reinforced Concrete Beams ◽  
Concrete Members ◽  
Steel Bars ◽  
Hybrid Reinforcement ◽  
Steel Hardening

Fibre-reinforced polymer (FRP)-reinforced concrete members exhibit low ductility due to the linear-elastic behaviour of FRP materials. Concrete members reinforced by hybrid FRP–steel bars can improve strength and ductility simultaneously. In this study, the plastic hinge problem of hybrid FRP–steel reinforced concrete beams was numerically assessed through finite element analysis (FEA). Firstly, a finite element model was proposed to validate the numerical method by comparing the simulation results with the test results. Then, three plastic hinge regions—the rebar yielding zone, concrete crushing zone, and curvature localisation zone—of the hybrid reinforced concrete beams were analysed in detail. Finally, the effects of the main parameters, including the beam aspect ratio, concrete grade, steel yield strength, steel reinforcement ratio, steel hardening modulus, and FRP elastic modulus on the lengths of the three plastic zones, were systematically evaluated through parametric studies. It is determined that the hybrid reinforcement ratio exerts a significant effect on the plastic hinge lengths. The larger the hybrid reinforcement ratio, the larger is the extent of the rebar yielding zone and curvature localisation zone. It is also determined that the beam aspect ratio, concrete compressive strength, and steel hardening ratio exert significant positive effects on the length of the rebar yielding zone.

scholarly journals FLEXURAL CAPACITY OF CONCRETE BEAMS REINFORCED WITH STEEL AND FIBRE‐REINFORCED POLYMER (FRP) BARS

2004 ◽  
Vol 10 (3) ◽  
pp. 209-215
Author(s):  
Hau Yan Leung
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Concrete Members ◽  
Reinforced Polymer ◽  
Beam Design ◽  
Reinforced Concrete Member ◽  
Current Design ◽  
Fibre Reinforced Polymer ◽  
Steel Rebars ◽  
Frp Bars

Although much research on concrete beams reinforced with fibre‐reinforced polymer (FRP) rods has been conducted in recent years, their use still does not receive the attention it deserves from practicising engineers. This is attributed to the fact that FRP is brittle in nature and the collapse of FRP‐reinforced concrete member may be catastrophic. A rational beam design can incorporate a hybrid use of FRP rods and steel rods. Current design codes only deal with steel‐reinforced or FRP‐reinforced concrete members. Therefore in this study some design charts and equations for concrete beam sections reinforced with FRP rods and steel rebars were generated. Results from the theoretical derivations agreed well with experimental data.

scholarly journals Effect of Steel Fibers on the Hysteretic Performance of Concrete Beams with Steel Reinforcement—Tests and Analysis

Materials ◽  
2020 ◽  
Vol 13 (13) ◽  
pp. 2923 ◽  
Author(s):  
Violetta K. Kytinou ◽  
Constantin E. Chalioris ◽  
Chris G. Karayannis ◽  
Anaxagoras Elenas
Keyword(s):  
Reinforced Concrete ◽  
Steel Reinforcement ◽  
Steel Fibers ◽  
Experimental Program ◽  
Engineering Practice ◽  
Cracking Behavior ◽  
Tension Softening ◽  
Proposed Model ◽  
Hysteretic Performance ◽  
Cracking Performance

The use of fibers as mass reinforcement to delay cracking and to improve the strength and the post-cracking performance of reinforced concrete (RC) beams has been well documented. However, issues of common engineering practice about the beneficial effect of steel fibers to the seismic resistance of RC structural members in active earthquake zones have not yet been fully clarified. This study presents an experimental and a numerical approach to the aforementioned question. The hysteretic response of slender and deep steel fiber-reinforced concrete (SFRC) beams reinforced with steel reinforcement is investigated through tests of eleven beams subjected to reversal cyclic loading and numerical analysis using 3D finite element (FE) modeling. The experimental program includes flexural and shear-critical SFRC beams with different ratios of steel reinforcing bars (0.55% and 1.0%), closed stirrups (from 0 to 0.5%), and fibers with content from 0.5 to 3% per volume. The developed nonlinear FE numerical simulation considers well-established relationships for the compression and tensional behavior of SFRC that are based on test results. Specifically, a smeared crack model is proposed for the post-cracking behavior of SFRC under tension, which employs the fracture characteristics of the composite material using stress versus crack width curves with tension softening. Axial tension tests of prismatic SFRC specimens are also included in this study to support the experimental project and to verify the proposed model. Comparing the numerical results with the experimental ones it is revealed that the proposed model is efficient and accurately captures the crucial aspects of the response, such as the SFRC tension softening effect, the load versus deformation cyclic envelope and the influence of the fibers on the overall hysteretic performance. The findings of this study also reveal that SFRC beams showed enhanced cyclic behavior in terms of residual stiffness, load-bearing capacity, deformation, energy dissipation ability and cracking performance, maintaining their integrity through the imposed reversal cyclic tests.

Sign in / Sign up

Export Citation Format

Share Document