scholarly journals An Accurate Analysis for Computation of Thermal Minimum Film Thickness in Inlet Zone in Hydrostatic Extrusion Process

2013 ◽  
Vol 8 (2) ◽  
pp. 171-178 ◽  
Author(s):  
Pankaj Tomar ◽  
Raj Kumar Pandey ◽  
Yogendra Nath
Keyword(s):  
Film Thickness ◽  
Extrusion Process ◽  
Hydrostatic Extrusion ◽  
Accurate Analysis ◽  
Minimum Film Thickness ◽  
Inlet Zone

Thermal and Starvation Effects on the Minimum Film Thickness in Inlet Zone in Cold Rolling

2008 ◽  
Vol 130 (2) ◽  
Author(s):  
P. Singh ◽  
R. K. Pandey ◽  
Y. Nath
Keyword(s):  
Film Thickness ◽  
Temperature Rise ◽  
Speed Reduction ◽  
Heating Effects ◽  
Empirical Relations ◽  
Viscous Shear ◽  
Minimum Film Thickness ◽  
Starvation Effects ◽  
Shear Heating ◽  
Inlet Zone

The main objective of this research is to analyze the variation of minimum film thickness in the inlet zone of roll-strip interface by incorporating starvation and viscous shear heating effects at high rolling speeds (5–20m∕s), reduction ratios (0.05–0.20), and slip values (varying up to 20%). An additional objective of this paper is to develop empirical relations for predictions of minimum film thicknesses (both isothermal and thermal) and maximum film temperature rise in the inlet zone of the lubricated roll strip contact as functions of roll-speed, reduction ratio, material parameter, slip, and starvation parameter. An efficient numerical method based on Lobatto quadrature technique is adopted for rigorous analysis of the present problem. The results reveal that the existence of starvation seems to be beneficial in terms of reduction in maximum film temperature rise as well as reduction in quantity of oil required for lubrication provided thin continuous film exists at the contact.

scholarly journals Film Thickness Calculations in Elastohydrodynamically Lubricated Circular Contacts, Using a Multigrid Method

1988 ◽  
Vol 110 (3) ◽  
pp. 503-507 ◽  
Author(s):  
A. A. Lubrecht ◽  
C. H. Venner ◽  
W. E. ten Napel ◽  
R. Bosma
Keyword(s):  
Film Thickness ◽  
Multigrid Method ◽  
Point Contact ◽  
Hertzian Contact ◽  
Medium Size ◽  
Fine Grid ◽  
Central Value ◽  
Minimum Film Thickness ◽  
Inlet Zone ◽  
The Cost

Minimum, central and average film thicknesses have been calculated for the isothermal E.H.L. point contact case, for a variety of load, rolling speed, and material parameters. The equations governing this problem were solved using a Multigrid method. This technique offers the possibility to work with a very fine grid, obtaining detailed and accurate solutions, at the cost of moderate cpu times and storage requirements, on medium size computers. Computations for low loads, requiring a large inlet zone, have been carried out using local grid refinements. The fluid in these calculations is assumed to be compressible and its viscosity-pressure behavior is described by either the Roelands equation, or the Barus equation. The ratio between the calculated minimum film thickness and the central value varied with the parameters governing the problem, but for low loads, a value of 3/4 was obtained. The film thickness behavior at these low loads can be accurately described in terms of the minimum film thickness. For higher loads, however, a description based on a film thickness, averaged over the Hertzian contact, is more appropriate to be compared with the asymptotic solution (Ertel, Grubin).

Thermal Elastohydrodynamic Lubrication of Heavily Loaded Line Contacts—An Efficient Inlet Zone Analysis

1998 ◽  
Vol 120 (1) ◽  
pp. 119-125 ◽  
Author(s):  
Mihir K. Ghosh ◽  
Raj K. Pandey
Keyword(s):  
Film Thickness ◽  
Thermal Loading ◽  
Elastohydrodynamic Lubrication ◽  
Thermal Reduction ◽  
Reduction Factor ◽  
Computationally Efficient ◽  
Rolling Velocity ◽  
Minimum Film Thickness ◽  
Line Contacts ◽  
Inlet Zone

An inlet zone analysis of TEHD lubrication of heavily loaded line contacts has been done using a computationally efficient and accurate numerical method based on Lobatto quadrature developed by Elrod and Brewe (1986). The results under extremely heavy conditions of dimensionless load W = 5.2*10−4 (pH = 2.0 GPa) and dimensionless rolling velocity U = 2.0*10−10(50 m/s) are presented. Significant reduction in thermal reduction factor (film thickness) at high rolling speeds relative to isothermal conditions have been observed. The results of the present work have been compared with the results of Wilson and Sheu (1983) and Hsu and Lee (1994). A correction formula of the thermal reduction factor for the minimum film thickness has been derived for a range of thermal loading parameters, loads, and slip ratios.

Predictive tool for frictional performance of piston ring-pack/liner conjunction

2019 ◽  
Vol 13 (3) ◽  
pp. 5513-5527
Author(s):  
J. W. Tee ◽  
S. H. Hamdan ◽  
W. W. F. Chong
Keyword(s):  
Film Thickness ◽  
Mathematical Models ◽  
Piston Ring ◽  
Published Data ◽  
Predictive Tool ◽  
Frictional Losses ◽  
Fundamental Understanding ◽  
Minimum Film Thickness ◽  
Piston Ring Pack ◽  
Ring Pack

Fundamental understanding of piston ring-pack lubrication is essential in reducing engine friction. This is because a substantial portion of engine frictional losses come from piston-ring assembly. Hence, this study investigates the tribological impact of different piston ring profiles towards engine in-cylinder friction. Mathematical models are derived from Reynolds equation by using Reynolds’ boundary conditions to generate the contact pressure distribution along the complete piston ring-pack/liner conjunction. The predicted minimum film thickness is then used to predict the friction generated between the piston ring-pack and the engine cylinder liner. The engine in-cylinder friction is predicted using Greenwood and Williamson’s rough surface contact model. The model considers both the boundary friction and the viscous friction components. These mathematical models are integrated to simulate the total engine in-cylinder friction originating from the studied piston ring-pack for a complete engine cycle. The predicted minimum film thickness and frictional properties from the current models are shown to correlate reasonably with the published data. Hence, the proposed mathematical approach prepares a simplistic platform in predicting frictional losses of piston ring-pack/liner conjunction, allowing for an improved fundamental understanding of the parasitic losses in an internal combustion engine.

Sinusoidal Three-Lobe Bearings—Optimization and Stability Charts

1980 ◽  
Vol 102 (4) ◽  
pp. 416-424 ◽  
Author(s):  
W. E. ten Napel ◽  
R. Bosma
Keyword(s):  
Film Thickness ◽  
Stability Parameters ◽  
Stability Regions ◽  
Damping Coefficients ◽  
Optimum Position ◽  
Minimum Film Thickness ◽  
Stiffness And Damping

In contradistinction to the commonly used segmented three-lobe bearing, another type of bearing, i.e., the sinusoidal three-lobe bearing has been investigated in this paper. The main advantage of this bearing is that it can very easily be manufactured. Special attention has been paid to problems of optimization with regard to minimum film thickness and friction, respectively. Stiffness and damping coefficients have been calculated as well as stability regions and stability parameters. Additionally, the optimum position of the oil grooves has been investigated.

Dynamic Analysis of Tilting-Pad Journal Bearing—Influence of Pad Deformations

1994 ◽  
Vol 116 (3) ◽  
pp. 621-627 ◽  
Author(s):  
H. Desbordes ◽  
M. Fillon ◽  
C. Chan Hew Wai ◽  
J. Frene
Keyword(s):  
Film Thickness ◽  
Pressure Field ◽  
Journal Bearing ◽  
Maximum Pressure ◽  
Tilting Pad ◽  
Minimum Film Thickness ◽  
Dimensional Finite Element ◽  
The One ◽  
Tilting Pad Journal Bearing ◽  
Tilting Pad Journal Bearings

A theoretical nonlinear analysis of tilting-pad journal bearings is presented for small and large unbalance loads under isothermal conditions. The radial displacements of internal pad surface due to pressure field are determined by a two-dimensional finite element method in order to define the actual film thickness. The influence of pad deformations on the journal orbit, on the minimum film thickness and on the maximum pressure is studied. The effects of pad displacements are to decrease the minimum film thickness and to increase the maximum pressure. The orbit amplitude is also increased by 20 percent for the large unbalance load compared to the one obtained for rigid pad.

Influence of Surface Waviness on the Thermal Elastohydrodynamic Lubrication of an Eccentric-Tappet Pair

2013 ◽  
Vol 135 (2) ◽  
Author(s):  
J. Wang ◽  
C. H. Venner ◽  
A. A. Lubrecht
Keyword(s):  
Film Thickness ◽  
Elastohydrodynamic Lubrication ◽  
Surface Waviness ◽  
Film Pressure ◽  
Oil Film ◽  
Working Cycle ◽  
Temperature Oscillations ◽  
Minimum Film Thickness ◽  
Traction Coefficient ◽  
Oil Film Pressure

The effect of single-sided and double-sided harmonic surface waviness on the film thickness, pressure, and temperature oscillations in an elastohydrodynamically lubricated eccentric-tappet pair has been investigated in relation to the eccentricity and the waviness wavelength. The results show that, during one working cycle, the waviness causes significant fluctuations of the oil film, pressure, and temperature, as well as a reduction in minimum film thickness. Smaller wavelength causes more dramatic variations in oil film. The fluctuations of the pressure, film thickness, temperature, and traction coefficient caused by double-sided waviness are nearly the same compared with the single-sided waviness, but the variations are less intense.

An Accurate Solution of the Gas Lubricated, Flat Sector Thrust Bearing

1977 ◽  
Vol 99 (1) ◽  
pp. 82-88 ◽  
Author(s):  
I. Etsion ◽  
D. P. Fleming
Keyword(s):  
Film Thickness ◽  
Thrust Bearing ◽  
Load Capacity ◽  
Thickness Distribution ◽  
Maximum Load ◽  
Accurate Solution ◽  
Operating Conditions ◽  
Thrust Bearings ◽  
Practical Design ◽  
Minimum Film Thickness

A flat sector shaped pad geometry for gas lubricated thrust bearings is analyzed considering both pitch and roll angles of the pad and the true film thickness distribution. Maximum load capacity is achieved when the pad is tilted so as to create a uniform minimum film thickness along the pad trailing edge. Performance characteristics for various geometries and operating conditions of gas thrust bearings are presented in the form of design curves. A comparison is made with the rectangular slider approximation. It is found that this approximation is unsafe for practical design, since it always overestimates load capacity.

Film thickness in elastohydrodynamically lubricated slender elliptic contacts: Part I – numerical studies of central film thickness

2021 ◽  
pp. 135065012110477
Author(s):  
Marius Wolf ◽  
Sergey Solovyev ◽  
Fatemi Arshia
Keyword(s):  
Film Thickness ◽  
State Of The Art ◽  
Experimental Studies ◽  
Elastohydrodynamic Lubrication ◽  
Large Parameter ◽  
Numerical Studies ◽  
Minimum Film Thickness ◽  
Subsequent Publication ◽  
New Formula ◽  
Increasing Load

In this paper, analytical equations for the central film thickness in slender elliptic contacts are investigated. A comparison of state-of-the-art formulas with simulation results of a multilevel elastohydrodynamic lubrication solver is conducted and shows considerable deviation. Therefore, a new film thickness formula for slender elliptic contacts with variable ellipticity is derived. It incorporates asymptotic solutions, which results in validity over a large parameter domain. It captures the behaviour of increasing film thickness with increasing load for specific very slender contacts. The new formula proves to be significantly more accurate than current equations. Experimental studies and discussions on minimum film thickness will be presented in a subsequent publication.

Sign in / Sign up

Export Citation Format

Share Document