scholarly journals Stress Transfer in High Performance Polyethylene Fiber Reinforced Epoxy Resin Composite Analyzed by X-Ray Diffraction. In the Direction Parallel to the Fiber Axis.

1998 ◽  
Vol 47 (10) ◽  
pp. 1083-1087 ◽  
Author(s):  
Takashi NISHINO ◽  
Kei NAKAMURA ◽  
Katsuhiko NAKAMAE
Keyword(s):  
Epoxy Resin ◽  
High Performance ◽  
Resin Composite ◽  
Stress Transfer ◽  
Fiber Axis ◽  
X Ray Diffraction ◽  
Direction Parallel ◽  
X Ray ◽  
Epoxy Resin Composite ◽  
Polyethylene Fiber

scholarly journals Thermal and Reliability Characterization of an Epoxy Resin-Based Double-Side Cooled Power Module

2021 ◽  
Vol 18 (3) ◽  
pp. 123-136
Author(s):  
Tzu-Hsuan Cheng ◽  
Kenji Nishiguchi ◽  
Yoshi Fukawa ◽  
B. Jayant Baliga ◽  
Subhashish Bhattacharya ◽  
...  
Keyword(s):  
Epoxy Resin ◽  
High Power ◽  
High Performance ◽  
Mechanical Performance ◽  
Resin Composite ◽  
Wide Band ◽  
Cost Effective ◽  
Power Module ◽  
Wide Band Gap ◽  
Epoxy Resin Composite

Abstract Wide-Band Gap (WBG) power devices have become a promising option for high-power applications due to the superior material properties over traditional Silicon. To not limit WBG devices’ mother nature, a rugged and high-performance power device packaging solution is necessary. This study proposes a Double-Side Cooled (DSC) 1.2 kV half-bridge power module having dual epoxy resin insulated metal substrate (eIMS) for solving convectional power module challenges and providing a cost-effective solution. The thermal performance outperforms traditional Alumina (Al2O3) Direct Bonded Copper (DBC) DSC power module due to moderate thermal conductivity (10 W/mK) and thin (120 mm) epoxy resin composite dielectric working as the IMS insulation layer. This novel organic dielectric can withstand high voltage (5 kVAC @ 120 μm) and has a Glass Transition Temperature (Tg) of 300°C, which is suitable for high-power applications. In the thermal-mechanical modeling, the organic DSC power module can pass the thermal cycling test over 1,000 cycles by optimizing the mechanical properties of the encapsulant material. In conclusion, this article not only proposes a competitive organic-based power module but also a methodology of evaluation for thermal and mechanical performance.

Preferred orientation of high performance carbon fibers

1992 ◽  
Vol 7 (9) ◽  
pp. 2612-2620 ◽  
Author(s):  
T. Hamada ◽  
M. Furuyama ◽  
T. Tomioka ◽  
M. Endo
Keyword(s):  
Heat Treatment ◽  
Carbon Fibers ◽  
High Performance ◽  
Preferred Orientation ◽  
Fiber Axis ◽  
Precursor Fiber ◽  
X Ray Diffraction ◽  
X Ray ◽  
Heat Treated ◽  
Clear Peak

The preferred orientation of polyacrylnitrile (PAN)-based carbon fibers, mesophase pitch-derived carbon fibers, and pitch precursor fibers was studied by using x-ray diffraction technique. The half width at half maximum (HWHM) intensity of the φ scan x-ray diffraction profiles of these fibers was a minimum at around 2θ = 26°. The result implies that a crystallite with a larger coherence length of crystallite size Lc(002) is better aligned along the fiber axis than that with a smaller Lc(002) in these fibers. Further, θ-2θ scan profiles depending on φ showed that a better aligned crystallite possesses a larger Lc(002) than a misaligned one. Lc(002) of a significantly misoriented crystallite remained constant at about 2 nm even after heat-treatment, though Lc(002) of a well-aligned crystallite was easily changed by heat-treatment for both PAN and pitch-based fibers. The pitch precursor fiber exhibited a clear peak at about 2θ = 7° in the θ-2θ profile and unusual ° scan profiles for 2θ around 7°, which were explained by assuming columnar structures formed by molecule stacking along the c-axis with periodic arrangements of the columns perpendicular to the c-axis. The periodic column stacking structure observed in the pitch precursor fiber was also detected in pitch-based carbon fibers heat-treated at lower temperatures.

Preparation and characterization of sodium silicate/epoxy resin composite bonded Nd-Fe-B magnets with high performance

2019 ◽  
Vol 37 (10) ◽  
pp. 1083-1087 ◽  
Author(s):  
Weiqiang Liu ◽  
Wang Xi ◽  
Ruijin Hu ◽  
Ming Yue ◽  
Yuxia Yin ◽  
...  
Keyword(s):  
Epoxy Resin ◽  
Sodium Silicate ◽  
High Performance ◽  
Resin Composite ◽  
Epoxy Resin Composite

scholarly journals Enhancement of Chloroprene/Natural/Butadiene Rubber Nanocomposite Properties Using Organoclays and Their Combination with Carbon Black as Fillers

Polymers ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1085
Author(s):  
Patricia Castaño-Rivera ◽  
Isabel Calle-Holguín ◽  
Johanna Castaño ◽  
Gustavo Cabrera-Barjas ◽  
Karen Galvez-Garrido ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Black ◽  
High Performance ◽  
Rubber Matrix ◽  
Butadiene Rubber ◽  
X Ray Diffraction ◽  
X Ray ◽  
Rubber Blends ◽  
Ft Ir ◽  
Chloroprene Rubber

Organoclay nanoparticles (Cloisite® C10A, Cloisite® C15) and their combination with carbon black (N330) were studied as fillers in chloroprene/natural/butadiene rubber blends to prepare nanocomposites. The effect of filler type and load on the physical mechanical properties of nanocomposites was determined and correlated with its structure, compatibility and cure properties using Fourier Transformed Infrared (FT-IR), X-ray Diffraction (XRD), Thermogravimetric Analysis (TGA) and rheometric analysis. Physical mechanical properties were improved by organoclays at 5–7 phr. Nanocomposites with organoclays exhibited a remarkable increase up to 46% in abrasion resistance. The improvement in properties was attributed to good organoclay dispersion in the rubber matrix and to the compatibility between them and the chloroprene rubber. Carbon black at a 40 phr load was not the optimal concentration to interact with organoclays. The present study confirmed that organoclays can be a reinforcing filler for high performance applications in rubber nanocomposites.

Sign in / Sign up

Export Citation Format

Share Document