scholarly journals Improvement of Low-Temperature Mechanical Properties of Ultrahigh Strength Low-Alloy Steels.

1995 ◽  
Vol 44 (503) ◽  
pp. 1035-1040
Author(s):  
YOSHIYUKI TOMITA
Keyword(s):  
Mechanical Properties ◽  
Low Temperature ◽  
Low Alloy Steels ◽  
Ultrahigh Strength ◽  
Alloy Steels

Effects of cooling rate on the mechanical properties of dual phase treated vanadium steels

1983 ◽  
Vol 41 ◽  
pp. 220-221
Author(s):  
L.J. Chen ◽  
H.C. Cheng ◽  
J.R. Gong ◽  
J.G. Yang
Keyword(s):  
Mechanical Properties ◽  
Cooling Rate ◽  
Automobile Industry ◽  
High Strength ◽  
Weight Percent ◽  
Low Alloy Steels ◽  
Dual Phase ◽  
Resource Requirement ◽  
Alloy Steels ◽  
Potential Weight

For fuel savings as well as energy and resource requirement, high strength low alloy steels (HSLA) are of particular interest to automobile industry because of the potential weight reduction which can be achieved by using thinner section of these steels to carry the same load and thus to improve the fuel mileage. Dual phase treatment has been utilized to obtain superior strength and ductility combinations compared to the HSLA of identical composition. Recently, cooling rate following heat treatment was found to be important to the tensile properties of the dual phase steels. In this paper, we report the results of the investigation of cooling rate on the microstructures and mechanical properties of several vanadium HSLA steels.The steels with composition (in weight percent) listed below were supplied by China Steel Corporation: 1. low V steel (0.11C, 0.65Si, 1.63Mn, 0.015P, 0.008S, 0.084Aℓ, 0.004V), 2. 0.059V steel (0.13C, 0.62S1, 1.59Mn, 0.012P, 0.008S, 0.065Aℓ, 0.059V), 3. 0.10V steel (0.11C, 0.58Si, 1.58Mn, 0.017P, 0.008S, 0.068Aℓ, 0.10V).

TRI-MARK TM-811N2

Alloy Digest ◽  
1983 ◽  
Vol 32 (4) ◽  
Keyword(s):  
Low Temperature ◽  
High Strength ◽  
Heat Treating ◽  
Low Alloy Steels ◽  
Nickel Steel ◽  
Fine Grained ◽  
Subzero Temperatures ◽  
Steel Weld Metal ◽  
Alloy Steels ◽  
Welding Electrode

Abstract TRI-MARK TM-811N2 is a flux-cored welding electrode for all position semiautomatic arc welding. It is designed to weld 2-3% nickel steels for applications requiring good toughness at subzero temperatures; in addition, it is used to weld various other high-strength low-alloy steels and various fine-grained steels with low-temperature toughness. Tri-Mark TM-811N2 is used to deposit typically 2.35% nickel steel weld metal with good low-temperature impact properties. It is used for shipbuilding, oil rigs and similar structures. This datasheet provides information on composition, physical properties, elasticity, and tensile properties as well as fracture toughness. It also includes information on corrosion resistance as well as heat treating, machining, and joining. Filing Code: SA-389. Producer or source: Tri-Mark Inc..

MECHANICAL PROPERTIES OF SINTER/FORGED LOW-ALLOY STEELS

1970 ◽  
Vol 13 (26) ◽  
pp. 165-194 ◽  
Author(s):  
R. T. CUNDILL ◽  
E. MARSH ◽  
K. A. RIDAL
Keyword(s):  
Mechanical Properties ◽  
Low Alloy Steels ◽  
Alloy Steels

scholarly journals Mechanical properties of low-alloy-steels with bainitic microstructures and varying carbon content

2016 ◽  
Vol 119 ◽  
pp. 012005
Author(s):  
A Weber ◽  
J Klarner ◽  
T Vogl ◽  
R Schöngrundner ◽  
G Sam ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Content ◽  
Low Alloy Steels ◽  
Alloy Steels

Hydrogen Compatibility and Suitability of (Ni)-Cr-Mo High-Strength Low-Alloy Seamless Line Pipe Steels for Pressure Vessels for Hydrogen Storage

2018 ◽  
Author(s):  
Akihide Nagao ◽  
Nobuyuki Ishikawa ◽  
Toshio Takano
Keyword(s):  
Mechanical Properties ◽  
High Pressure ◽  
High Strength ◽  
Pressure Vessels ◽  
Hydrogen Gas ◽  
Low Alloy Steels ◽  
Pipe Steels ◽  
Line Pipe ◽  
Alloy Steels ◽  
Pressure Hydrogen

Cr-Mo and Ni-Cr-Mo high-strength low-alloy steels are candidate materials for the storage of high-pressure hydrogen gas. Forging materials of these steels have been used for such an environment, while there has been a strong demand for a higher performance material with high resistance to hydrogen embrittlement at lower cost. Thus, mechanical properties of Cr-Mo and Ni-Cr-Mo steels made of quenched and tempered seamless pipes in high-pressure hydrogen gas up to 105 MPa were examined in this study. The mechanical properties were deteriorated in the presence of hydrogen that appeared in reduction in local elongation, decrease in fracture toughness and accelerated fatigue-crack growth rate, although the presence of hydrogen did not affect yield and ultimate tensile strengths and made little difference to the fatigue endurance limit. It is proposed that pressure vessels for the storage of gaseous hydrogen made of these seamless line pipe steels can be designed.

Sign in / Sign up

Export Citation Format

Share Document