scholarly journals Towards the Determination of Chloride Profiles by means of Resistivity Measurements in Reinforced Concrete

2020 ◽  
Author(s):  
G. Villain ◽  
M. Alhajj ◽  
S. Lopes ◽  
V. Bouteiller
Keyword(s):  
Reinforced Concrete ◽  
Resistivity Measurements ◽  
Chloride Profiles

Determination of reinforced concrete durability with on-site resistivity measurements

2016 ◽  
Vol 50 (1) ◽  
Author(s):  
Javier Sanchez ◽  
Carmen Andrade ◽  
Julio Torres ◽  
Nuria Rebolledo ◽  
Jose Fullea
Keyword(s):  
Reinforced Concrete ◽  
Concrete Durability ◽  
Resistivity Measurements

Improvement Of Curvilinear Diagrams Of Concrete Deformation

2019 ◽  
pp. 99-104
Keyword(s):  
Reinforced Concrete ◽  
Peak Load ◽  
Experimental Studies ◽  
Concrete Structures ◽  
Deformation Model ◽  
Reinforced Concrete Structures ◽  
Significant Difference ◽  
Deformation Diagrams

Problems when calculating reinforced concrete structures based on the concrete deformation under compression diagram, which is presented both in Russian and foreign regulatory documents on the design of concrete and reinforced concrete structures are considered. The correctness of their compliance for all classes of concrete remains very approximate, especially a significant difference occurs when using Euronorm due to the different shape and sizes of the samples. At present, there are no methodical recommendations for determining the ultimate relative deformations of concrete under axial compression and the construction of curvilinear deformation diagrams, which leads to limited experimental data and, as a result, does not make it possible to enter more detailed ultimate strain values into domestic standards. The results of experimental studies to determine the ultimate relative deformations of concrete under compression for different classes of concrete, which allowed to make analytical dependences for the evaluation of the ultimate relative deformations and description of curvilinear deformation diagrams, are presented. The article discusses various options for using the deformation model to assess the stress-strain state of the structure, it is concluded that it is necessary to use not only the finite values of the ultimate deformations, but also their intermediate values. This requires reliable diagrams "s–e” for all classes of concrete. The difficulties of measuring deformations in concrete subjected to peak load, corresponding to the prismatic strength, as well as main cracks that appeared under conditions of long-term step loading are highlighted. Variants of more accurate measurements are proposed. Development and implementation of the new standard GOST "Concretes. Methods for determination of complete diagrams" on the basis of the developed method for obtaining complete diagrams of concrete deformation under compression for the evaluation of ultimate deformability of concrete under compression are necessary.

EXPERIMENTAL STUDIES OF REINFORCED CONCRETE STRUCTURES WITH CROSS-SHAPED SPATIAL CRACK UNDER TORSION WITH BENDING

2020 ◽  
Vol 92 (6) ◽  
pp. 13-25
Author(s):  
Vl.I. KOLCHUNOV ◽  
◽  
A.I. DEMYANOV ◽  
M.M. MIHAILOV ◽  
◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
Experimental Determination ◽  
Calculation Method ◽  
Experimental Studies ◽  
Concrete Structures ◽  
Design Parameters ◽  
Reinforced Concrete Structures ◽  
Experimental Scheme

The article offers a method and program for experimental studies of reinforced concrete structures with cross-shaped spatial crack under torsion with bending, the main purpose of which is to check the design assumptions and experimental determination of the design parameters of the proposed calculation method. The conducted experimental studies provide an opportunity to test the proposed calculation apparatus and clarify the regularities for determining deflections, angles of rotation of extreme sections, and stresses in the compressed zone of concrete. For analysis, the article presents a typical experimental scheme for the formation and development of cracks in the form of a sweep, as well as characteristic graphs of the dependence of the angles of rotation of end sections.

On-Site Determination of the Polarization Resistance in a Reinforced Concrete Beam

CORROSION ◽  
1988 ◽  
Vol 44 (10) ◽  
pp. 761-765 ◽  
Author(s):  
S. Feliu ◽  
J. A. Gonzalez ◽  
C. Andrade ◽  
V. Feliu
Keyword(s):  
Reinforced Concrete ◽  
Polarization Resistance ◽  
Concrete Beam ◽  
Reinforced Concrete Beam

Design charts for reinforced concrete L-sections

1976 ◽  
Vol 3 (4) ◽  
pp. 479-483
Author(s):  
Maher K. Tadros
Keyword(s):  
Reinforced Concrete ◽  
Ultimate Strength ◽  
Normal Force ◽  
Basic Assumptions ◽  
Design Charts ◽  
Strength Design

The object of this paper is to present charts for the ultimate strength design of L-sections subjected to combined normal force and bending. The method of derivation of these charts is briefly described. It is general and applicable to other odd-shaped sections. It also conforms to the basic assumptions adopted in the CSA Standard A 23.3-1973. The charts can be used either for the determination of the dimensions of the section or for the check of its capacity.

scholarly journals Analyzing of Coatings on Steel - Reinforced Concrete Elements by Mobile NMR

2016 ◽  
Vol 62 (1) ◽  
pp. 65-82 ◽  
Author(s):  
J. Orlowsky
Keyword(s):  
Reinforced Concrete ◽  
Potential Effect ◽  
Building Site ◽  
Steel Reinforced Concrete ◽  
Mobile Nmr ◽  
The Individual ◽  
First Time ◽  
Concrete Elements ◽  
Non Destructive

Abstract A large number of infrastructural concrete buildings are protected against aggressive environments by coating systems. The functionality of these coating systems is mainly affected by the composition and thickness of the individual polymeric layers. For the first time ever, a mobile nuclear magnetic resonance (NMR) sensor allows a non-destructive determination of these important parameters on the building site. However, before this technique can be used on steel-reinforced concrete elements, the potential effect of the reinforcement on the measurement, i.e. the NMR signal, needs to be studied. The results show a shift of the NMR profile as well as an increase of the signals amplitude in the case of the reinforced samples, while calculating the thickness of concrete coating leading to identical results.

scholarly journals Determination of the neutralization depth of concrete under the aggressive environment influence

2018 ◽  
Vol 33 ◽  
pp. 02010 ◽  
Author(s):  
Anastasia Morzhukhina ◽  
Stanislav Nikitin ◽  
Elena Akimova
Keyword(s):  
Reinforced Concrete ◽  
Chloride Ions ◽  
The Body ◽  
Chemical Plants ◽  
Reinforced Concrete Structure ◽  
Load Bearing Capacity ◽  
High Rise ◽  
Capacity Loss ◽  
Air Penetration

Aggressive environments have a significant impact on destruction of many reinforced concrete structures, such as high-rise constructions or chemical plants. For example, some high-rise constructions are equipped with a swimming pool, so they are exposed to chloride ions in the air. Penetration of aggressive chemical substances into the body of concrete contributes to acceleration of reinforced concrete structure corrosion that in turn leads to load bearing capacity loss and destruction of the building. The article considers and analyzes the main technologies for calculating penetration depth of various aggressive substances into the body of concrete. The calculation of corrosion depth was made for 50-year service life.

Sign in / Sign up

Export Citation Format

Share Document