SELECTION AND VALIDATION OF CALCULATED PARAMETERS OF LARGE-SIZED TIRES FOR EVALUATING THE MOVEMENT DYNAMICS OF AGRICULTURAL MACHINES USING NUMERICAL SIMULATION

2020 ◽  
Author(s):  
K.A. Mogilnikov ◽  
Keyword(s):  
Numerical Simulation ◽  
Model Parameters ◽  
Tire Model ◽  
Movement Dynamics ◽  
Straight Line ◽  
Low Speeds ◽  
Line Path ◽  
Wheeled Vehicles ◽  
Agricultural Machines

The article provides an overview of tire model parameters used in the calculation of the wheeled vehicles dynamics when driving on roads or agricultural background. A list of parameters that are not essential for simulation the movement of machines at low speeds, mainly along a straight line path, is determined. A method for determining the necessary parameters is presented, an example of their calculation is given.

In-Plane Flexible Ring Tire Model—Part 1: Modeling and Parameter Identification

2018 ◽  
Vol 46 (3) ◽  
pp. 174-219 ◽  
Author(s):  
Bin Li ◽  
Xiaobo Yang ◽  
James Yang ◽  
Yunqing Zhang ◽  
Zeyu Ma
Keyword(s):  
Static Load ◽  
Model Parameters ◽  
Tire Model ◽  
Test Results ◽  
Lumped Mass ◽  
Virtual Test ◽  
Proposed Model ◽  
Particle Swarm Method ◽  
Vehicle Dynamic Simulation ◽  
Flexible Ring

ABSTRACT The tire model is essential for accurate and efficient vehicle dynamic simulation. In this article, an in-plane flexible ring tire model is proposed, in which the tire is composed of a rigid rim, a number of discretized lumped mass belt points, and numerous massless tread blocks attached on the belt. One set of tire model parameters is identified by approaching the predicted results with ADAMS® FTire virtual test results for one particular cleat test through the particle swarm method using MATLAB®. Based on the identified parameters, the tire model is further validated by comparing the predicted results with FTire for the static load-deflection tests and other cleat tests. Finally, several important aspects regarding the proposed model are discussed.

Vector field path following of a full-wing solar-powered Unmanned Aerial Vehicle (UAV) landing based on Dubins path: a lesson from multiple landing failures

2021 ◽  
pp. 1-30
Author(s):  
A. Guo ◽  
Z. Zhou ◽  
R. Wang ◽  
X. Zhao ◽  
X. Zhu
Keyword(s):  
Vector Field ◽  
Path Following ◽  
Endurance Performance ◽  
Electrical Energy ◽  
Lateral Control ◽  
Special Configuration ◽  
Straight Line ◽  
Lateral Distance ◽  
Solar Powered ◽  
Line Path

Abstract The full-wing solar-powered UAV has a large aspect ratio, special configuration, and excellent aerodynamic performance. This UAV converts solar energy into electrical energy for level flight and storage to improve endurance performance. The UAV only uses a differential throttle for lateral control, and the insufficient control capability during crosswind landing results in a large lateral distance bias and leads to multiple landing failures. This paper analyzes 11 landing failures and finds that a large lateral distance bias at the beginning of the approach and the coupling of base and differential throttle control is the main reason for multiple landing failures. To improve the landing performance, a heading angle-based vector field (VF) method is applied to the straight-line and orbit paths following and two novel 3D Dubins landing paths are proposed to reduce the initial lateral control bias. The results show that the straight-line path simulation exhibits similar phenomenon with the practical failure; the single helical path has the highest lateral control accuracy; the left-arc to left-arc (L-L) path avoids the saturation of the differential throttle; and both paths effectively improve the probability of successful landing.

Identification of Tire Model Parameters Through Full Vehicle Experimental Tests

2011 ◽  
Vol 133 (3) ◽  
Author(s):  
Francesco Braghin ◽  
Federico Cheli ◽  
Edoardo Sabbioni
Keyword(s):  
Laboratory Tests ◽  
Experimental Tests ◽  
Contact Forces ◽  
Lateral Acceleration ◽  
Design Stage ◽  
Model Parameters ◽  
Tire Model ◽  
Identification Procedure ◽  
Sideslip Angle ◽  
Tyre Model

Individual tire model parameters are traditionally derived from expensive component indoor laboratory tests as a result of an identification procedure minimizing the error with respect to force and slip measurements. These parameters are then transferred to vehicle models used at a design stage to simulate the vehicle handling behavior. A methodology aimed at identifying the Magic Formula-Tyre (MF-Tyre) model coefficients of each individual tire for pure cornering conditions based only on the measurements carried out on board vehicle (vehicle sideslip angle, yaw rate, lateral acceleration, speed and steer angle) during standard handling maneuvers (step-steers) is instead presented in this paper. The resulting tire model thus includes vertical load dependency and implicitly compensates for suspension geometry and compliance (i.e., scaling factors are included into the identified MF coefficients). The global number of tests (indoor and outdoor) needed for characterizing a tire for handling simulation purposes can thus be reduced. The proposed methodology is made in three subsequent steps. During the first phase, the average MF coefficients of the tires of an axle and the relaxation lengths are identified through an extended Kalman filter. Then the vertical loads and the slip angles at each tire are estimated. The results of these two steps are used as inputs to the last phase, where, the MF-Tyre model coefficients for each individual tire are identified through a constrained minimization approach. Results of the identification procedure have been compared with experimental data collected on a sport vehicle equipped with different tires for the front and the rear axles and instrumented with dynamometric hubs for tire contact forces measurement. Thus, a direct matching between the measured and the estimated contact forces could be performed, showing a successful tire model identification. As a further verification of the obtained results, the identified tire model has also been compared with laboratory tests on the same tire. A good agreement has been observed for the rear tire where suspension compliance is negligible, while front tire data are comparable only after including a suspension compliance compensation term into the identification procedure.

scholarly journals Extended Kalman Filter for Bearings-Only Tracking

2019 ◽  
Vol 8 (6) ◽  
pp. 637-640 ◽  
Keyword(s):  
Kalman Filter ◽  
Extended Kalman Filter ◽  
Constant Velocity ◽  
Target Motion ◽  
Passive Mode ◽  
Crucial Issue ◽  
Straight Line ◽  
Optimal Linear ◽  
Target Motion Analysis ◽  
Line Path

Target tracking using bearings-only measurements in passive mode operation of sonar is a crucial issue of underwater tracking. Target motion in underwater scenario is analyzed using bearings-only measurements and calculating parameters like range, course and speed of the target. This is called Target Motion Analysis (TMA). TMA process is highly non-linear as the measurements chosen are nonlinearly related to the selected target state vector and the traditional, optimal linear Kalman filter will not be appropriate to use. It is presumed that the target is moving in straight line path with constant velocity, so Extended Kalman Filter (EKF) is proposed in this paper. The algorithm is simulated for several scenarios using MATLAB. Monte-Carlo runs are performed to evaluate the capability of the algorithm.

Robustness Analysis of a Simple and Augmented Proportional Plus Derivative Controller in Trajectory Following Robots Using the Floquet Theory

2018 ◽  
Vol 13 (7) ◽  
Author(s):  
B. Sandeep Reddy ◽  
Ashitava Ghosal
Keyword(s):  
Numerical Simulation ◽  
Degrees Of Freedom ◽  
Floquet Theory ◽  
Robustness Analysis ◽  
Periodic Trajectory ◽  
Model Parameters ◽  
Asymptotically Stable ◽  
Pd Controller ◽  
Simulation Results ◽  
Trajectory Following

This paper deals with the issue of robustness in control of robots using the proportional plus derivative (PD) controller and the augmented PD controller. In the literature, a variety of PD and model-based controllers for multilink serial manipulator have been claimed to be asymptotically stable for trajectory tracking, in the sense of Lyapunov, as long as the controller gains are positive. In this paper, we first establish that for simple PD controllers, the criteria of positive controller gains are insufficient to establish asymptotic stability, and second that for the augmented PD controller the criteria of positive controller gains are valid only when there is no uncertainty in the model parameters. We show both these results for a simple planar two-degrees-of-freedom (2DOFs) robot with two rotary (R) joints, following a desired periodic trajectory, using the Floquet theory. We provide numerical simulation results which conclusively demonstrate the same.

Thermal–Mechanical Coupling Evaluation of the Panel Performance of a Prefabricated Cabin-Type Substation Based on Machine Learning

Fire ◽  
2021 ◽  
Vol 4 (4) ◽  
pp. 93
Author(s):  
Xiangsheng Lei ◽  
Jinwu Ouyang ◽  
Yanfeng Wang ◽  
Xinghua Wang ◽  
Xiaofeng Zhang ◽  
...  
Keyword(s):  
Neural Network ◽  
Machine Learning ◽  
Numerical Simulation ◽  
Fire Resistance ◽  
Bp Neural Network ◽  
Stress Test ◽  
Normal Operation ◽  
Model Parameters ◽  
Mechanical Coupling ◽  
The Impact

The panel performance of a prefabricated cabin-type substation under the impact of fires plays a vital role in the normal operation of the substation. However, current evaluations of the panel performance of substations under fire still focus on fire resistance tests, which seldom consider the relationship between fire behavior and the mechanical load of the panel under the impact of fires. Aiming at the complex and uncertain relationship between the thermal and mechanical performance of the substation panel under impact of fires, this paper proposes a machine learning method based on a BP neural network. First, the fire resistance test and the stress test of the panel is carried out, then a machine learning model is established based on the BP neural network. According to the collected data, the model parameters are obtained through a series of training and verification processes. Meanwhile, the correlation between the panel performance and fire resistance was obtained. Finally, related parameters are input into the thermal–mechanical coupling evaluation model for the substation panel performance to evaluate the fire resistance performance of the substation panel. To verify the correctness of the established model, numerical simulation of the fire test and stress test of the panel is conducted, and numerical simulation samples are predicted by the trained model. The results show that the prediction curve of neural network is closer to the real results compared with the numerical simulation, and the established model can accurately evaluate the thermal–mechanical coupling performance of the substation panel under fire.

Composite finite-time straight-line path-following control of an underactuated surface vessel

2020 ◽  
Vol 357 (16) ◽  
pp. 11496-11517 ◽  
Author(s):  
Qiankang Hou ◽  
Li Ma ◽  
Shihong Ding ◽  
Xiaofei Yang ◽  
Xiangyong Chen
Keyword(s):  
Finite Time ◽  
Path Following ◽  
Path Following Control ◽  
Straight Line ◽  
Line Path ◽  
Surface Vessel
Sign in / Sign up

Export Citation Format

Share Document