scholarly journals Comparison of the adsorption capacity of methylene blue nanostructured composites based on CoMnO2 and CuO

2021 ◽  
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Nanostructured Composites

Analisis Variasi Temperatur Aktivasi Terhadap Daya Serap Arang Aktif Tandan Aren (Arenga Pinnata Merr) Dengan Agen Aktivasi Potassium Silicate(K2SiO3)

2020 ◽  
Vol 5 (3) ◽  
pp. 221
Author(s):  
Muhammad Azam ◽  
Muhammad Anas ◽  
Erniwati Erniwati
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Temperature Variation ◽  
Chemical Activation ◽  
Weight Ratio ◽  
Potassium Silicate ◽  
Physical Activation ◽  
Activation Temperature ◽  
Pyrolysis Reactor

This study aims to determine the effect of variation of activation temperature of activated carbon from sugar palm bunches of chemically activatied with the activation agent of potassium silicate (K2SiO3) on the adsorption capacity of iodine and methylene blue. Activated carbon from bunches of sugar palmacquired in four steps: preparationsteps, carbonizationstepsusing the pyrolysis reactor with temperature of 300 oC - 400 oC for 8 hours and chemical activation using of potassium silicate (K2SiO3) activator in weight ratio of 2: 1 and physical activation using the electric furnace for 30 minutes with temperature variation of600 oC, 650 oC, 700 oC, 750 oC and 800 oC. The iodine and methyleneblue adsorption testedby Titrimetric method and Spectrophotometry methodrespectively. The results of the adsorption of iodine and methylene blue activated carbon from sugar palm bunches increased from 240.55 mg/g and 63.14 mg/g at a temperature of 600 oC to achieve the highest adsorption capacity of 325.80 mg/g and 73.59 mg/g at temperature of 700 oC and decreased by 257.54 mg/g and 52.03 mg/g at a temperature of 800 oCrespectively.However, it does not meet to Indonesia standard (Standard Nasional Indonesia/SNI), which is 750 mg/g and 120 mg/g respectively.

scholarly journals One-step synthesis of nitrogen-grafted copper-gallic acid for enhanced methylene blue removal

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Shella Permatasari Santoso ◽  
Vania Bundjaja ◽  
Artik Elisa Angkawijaya ◽  
Chintya Gunarto ◽  
Alchris Woo Go ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Gallic Acid ◽  
Synthesis Method ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
Temperature Dependent ◽  
One Step ◽  
Detailed Assessment ◽  
Higher Temperature

AbstractNitrogen-grafting through the addition of glycine (Gly) was performed on a metal- phenolic network (MPN) of copper (Cu2+) and gallic acid (GA) to increase its adsorption capacity. Herein, we reported a one-step synthesis method of MPN, which was developed according to the metal–ligand complexation principle. The nitrogen grafted CuGA (Ng-CuGA) MPN was obtained by reacting Cu2+, GA, and Gly in an aqueous solution at a molar ratio of 1:1:1 and a pH of 8. Several physicochemical measurements, such as Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), N2 sorption, X-ray diffraction (XRD), and thermal gravimetry analysis (TGA), were done on Ng-CuGA to elucidate its characteristics. The analysis revealed that the Ng-CuGA has non-uniform spherical shaped morphology with a pore volume of 0.56 cc/g, a pore size of 23.25 nm, and thermal stability up to 205 °C. The applicational potential of the Ng-CuGA was determined based on its adsorption capacity against methylene blue (MB). The Ng-CuGA was able to adsorb 190.81 mg MB per g adsorbent at a pH of 6 and temperature of 30 °C, which is 1.53 times higher than the non-grafted CuGA. Detailed assessment of Ng-CuGA adsorption properties revealed their pH- and temperature-dependent nature. The adsorption capacity and affinity were found to decrease at a higher temperature, demonstrating the exothermic adsorption behavior.

Ouricuri (Syagrus coronata) fiber: a novel biosorbent to remove methylene blue from aqueous solutions

2016 ◽  
Vol 75 (1) ◽  
pp. 106-114 ◽  
Author(s):  
Lucas Meili ◽  
Társila Santos da Silva ◽  
Daniely Carlos Henrique ◽  
João Inácio Soletti ◽  
Sandra Helena Vieira de Carvalho ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Experimental Design ◽  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Adsorption Process ◽  
Fiber Diameter ◽  
Aqueous Media ◽  
Process Efficiency ◽  
Maximum Adsorption Capacity ◽  
Equilibrium Studies

In this work, the potential of ouricuri (Syagrus coronata) fiber as a novel biosorbent to remove methylene blue (MB) from aqueous solutions was investigated. The fiber was prepared and characterized according to the fundamental features for adsorption. A 23 experimental design was used to evaluate the effects of adsorbent dosage (M), fiber diameter (D) and agitation (A) on the adsorption capacity. In the more adequate conditions, kinetic and equilibrium studies were performed. The experimental design results showed that M = 10 g L−1), D = 0.595 mm and A = 200 rpm were the more adequate conditions for MB adsorption. Based on the kinetic study, it was found that the adsorption process was fast, being the equilibrium was attained at about 5 min, with 90% of color removal. The isotherm was properly represented by the Sips model, and the maximum adsorption capacity was 31.7 mg g−1. In brief, it was demonstrated that ouricuri fiber is an alternative biosorbent to remove MB from aqueous media, taking into account the process efficiency and economic viewpoint.

scholarly journals Kinetic Study of the Bioadsorption of Methylene Blue on the Surface of the Biomass Obtained from the Algae D. antarctica

2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
Jhonatan R. Guarín ◽  
Juan Carlos Moreno-Pirajan ◽  
Liliana Giraldo
Keyword(s):  
Methylene Blue ◽  
Kinetic Study ◽  
Adsorption Capacity ◽  
Scientific Community ◽  
Second Order ◽  
Maximum Adsorption Capacity ◽  
Pseudo Second Order ◽  
Best Fit ◽  
Total Elimination ◽  
Purification Of Water

Currently, there is a great pollution of water by the dyes; due to this, several studies have been carried out to remove these compounds. However, the total elimination of these pollutants from the aquatic effluents has represented a great challenge for the scientific community, for which it is necessary to carry out investigations that allow the purification of water. In this work, we studied the bioadsorption of methylene blue on the surface of the biomass obtained from the algae D. antarctica. This material was characterized by SEM and FTIR. To the data obtained in the biosorption experiments, different models of biosorption and kinetics were applied, finding that the best fit to the obtained data is given by applying the pseudo-second-order models and the Toth model, respectively. It was also determined that the maximum adsorption capacity of MB on the surface of the biomass is 702.9 mg/g, which shows that this material has great properties as a bioadsorbent.

Adsorption of Methylene Blue from Aqueous Solution Using Honeycomb-Cinder

2012 ◽  
Vol 550-553 ◽  
pp. 2259-2262
Author(s):  
Song Bo Cui ◽  
Hua Yong Zhang ◽  
Lu Yi Zhang
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Ph Value ◽  
Dye Wastewater ◽  
Batch System ◽  
Adsorption Data ◽  
Adsorption Processes ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Mb Adsorption

The adsorption behavior of methylene blue (MB) dye from aqueous solutions onto honeycomb-cinder (HC) and its acid-activated product was investigated in a batch system. The results showed the adsorption capacity was decreased for raw HC samples with the increase of pH value, while it was increased for activated samples. The adsorption data were fit with Langmuir isotherm model for MB adsorption by all samples. The MB adsorption capacity on samples was increased from 2.62 mg/g to 7.81 mg/g and 7.00 mg/g after acid-activated by HCl and H2SO4, respectively. The adsorption processes of MB followed pseudo-second-order kinetics with a coefficient of correlation≥0.99. This study demonstrated that acid-activated HC has superior adsorbing ability for MB than raw HC and can be used as alternative adsorbents in dye wastewater treatment.

Synthesis and characterization of pecan nutshell-based adsorbent with high specific area and high methylene blue adsorption capacity

2019 ◽  
Vol 276 ◽  
pp. 570-576 ◽  
Author(s):  
Hugo H.C. Lima ◽  
Rogério S. Maniezzo ◽  
Maria E.G. Llop ◽  
Vincente L. Kupfer ◽  
Pedro A. Arroyo ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Specific Area ◽  
Synthesis And Characterization ◽  
Methylene Blue Adsorption ◽  
Pecan Nutshell ◽  
High Specific Area

Morphology dependent adsorption of methylene blue on trititanate nanoplates and nanotubes prepared by the hydrothermal treatment of TiO2

2016 ◽  
Vol 75 (2) ◽  
pp. 350-357
Author(s):  
Graham Dawson ◽  
Wei Chen ◽  
Luhua Lu ◽  
Kai Dai
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Pore Volume ◽  
Hydrothermal Reaction ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
High Capacity ◽  
Adsorption Properties

The adsorption properties of two nanomorphologies of trititanate, nanotubes (TiNT) and plates (TiNP), prepared by the hydrothermal reaction of concentrated NaOH with different phases of TiO2, were examined. It was found that the capacity for both morphologies towards methylene blue (MB), an ideal pollutant, was extremely high, with the TiNP having a capacity of 130 mg/g, higher than the TiNT, whose capacity was 120 mg/g at 10 mg/L MB concentration. At capacity, the well-dispersed powders deposit on the floor of the reaction vessel. The two morphologies had very different structural and adsorption properties. TiNT with high surface area and pore volume exhibited exothermic monolayer adsorption of MB. TiNP with low surface area and pore volume yielded a higher adsorption capacity through endothermic multilayer adsorption governed by pore diffusion. TiNP exhibited a higher negative surface charge of −23 mV, compared to −12 mV for TiNT. The adsorption process appears to be an electrostatic interaction, with the cationic dye attracted more strongly to the nanoplates, resulting in a higher adsorption capacity and different adsorption modes. We believe this simple, low cost production of high capacity nanostructured adsorbent material has potential uses in wastewater treatment.

Few-Layered MoS2 Synthesized by Hydrothermal Method with Improved Adsorption Capacity for Methylene Blue Than Active Carbon

2018 ◽  
Vol 18 (11) ◽  
pp. 7948-7951 ◽  
Author(s):  
Cuiqing Zhang ◽  
Xiaoyu Li ◽  
Chengjiang Lian ◽  
Changyuan Hu ◽  
Shuwang Duo ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Hydrothermal Method ◽  
Active Carbon ◽  
Layered Mos2

scholarly journals Study on the adsorption of methylene blue from aqueous solution using hydrogel glucomannan/graphene oxide

2021 ◽  
Vol 10 (1) ◽  
pp. 59-66
Author(s):  
Son Le Lam ◽  
Phu Nguyen Vinh ◽  
Hieu Le Trung ◽  
Tan Le Thua ◽  
Nhan Dang Thi Thanh ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Methylene Blue ◽  
Graphene Oxide ◽  
Adsorption Capacity ◽  
Organic Dyes ◽  
Dye Adsorption ◽  
Order Kinetic ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order

Glucomannan/graphene oxide (GM/GO) hydrogel was synthesized by using calcium hydroxide as the crosslinker. The synthesized material was characterized by using IR, XRD, SEM, EDX and RAMAN technology. The composite hydrogel was used for removal of organic dyes from aqueous solution. The results showed that the GM/GO hydrogel had a porous structure and a high adsorption capacity toward methylene blue (MB). The pseudo-second-order kinetic model could fit the rate equation of MB adsorption onto the GM/GO hydrogel. The adsorption of MB onto GM/GO hydrogel was a spontaneous process. In addition, the equilibrium adsorption isotherm data indicated that equilibrium data were fitted to the Langmuir isotherm and the maximum dye adsorption capacity was 198,69 mg.g-1. Moreover, the hydrogel was stable and easily recovered and adsorption capacity was around 97% of the initial saturation adsorption capacity after being used five times.

scholarly journals Study of The Acid-Base Effect on Zeolite Activation and Its Characterization as Adsorbent of Methylene Blue Dye

2017 ◽  
Vol 2 (2) ◽  
pp. 90 ◽  
Author(s):  
Yulius Dala Ngapa
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Natural Zeolite ◽  
Blue Dye ◽  
Activation Process ◽  
Acid Base ◽  
Isothermal Adsorption ◽  
Naoh Solution ◽  
Equilibrium Process

<p>Activation is one of the processes by which are mostly done to improve the quality of natural zeolite. Activation process by zeolite will change the ratio of the Si/Al and can increase the formation of empty cavities so that the capability of zeolite as an adsorbent be optimal. In this research, natural zeolite from the district of Ende, Nusa Tenggara Timur. Activation Ende natural zeolite done chemically using HCl and NaOH solution, with variations concentrate 0,5 M; 1,5 M; and 3,0 M. Next, zeolite which has activated used to adsorb dye methylene blue. Based on the research results, chemically of activation from natural zeolite can increase the adsorption capacity to substance methylene blue. The adsorption capacity in the Ende natural and after activation is 17,289 mg/g and 19,98 mg/g respectively. The Langmuir model most closely matched the isothermal adsorption of equilibrium process.</p>

Sign in / Sign up

Export Citation Format

Share Document