Characterization of morphology and mechanical properties of glass interior irradiated by femtosecond laser

2009 ◽  
Author(s):  
Panjawat Kongsuwan ◽  
Hongliang Wang ◽  
Sinisa Vukelic ◽  
Y. Lawrence Yao
Keyword(s):  
Mechanical Properties ◽  
Femtosecond Laser ◽  
Morphology And Mechanical Properties

scholarly journals Femtosecond laser machining for characterization of local mechanical properties of biomaterials: a case study on wood

2017 ◽  
Vol 18 (1) ◽  
pp. 574-583 ◽  
Author(s):  
Severin Jakob ◽  
Manuel J. Pfeifenberger ◽  
Anton Hohenwarter ◽  
Reinhard Pippan
Keyword(s):  
Mechanical Properties ◽  
Femtosecond Laser ◽  
Laser Machining

Effect of Ultrasonic Treatment on Morphology and Mechanical Properties of Bioplastic from Cassava Starch with Nanoclay Reinforcement

2017 ◽  
Vol 29 ◽  
pp. 35-41 ◽  
Author(s):  
Nanang Eko Wahyuningtiyas ◽  
Heru Suryanto
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Tensile Strength ◽  
Cassava Starch ◽  
Maximum Hardness ◽  
Blending Method ◽  
Sonication Treatment ◽  
Morphology And Mechanical Properties ◽  
Scanning Electron

The research is to investigate influence of sonication treatment on the morphologi and mechanical properties of bioplastic filler nanoclay with different nanoclay concentration. The bioplastic was prepared using blending method among bioplastic, glycerol, and nanoclay with assistance of sonication treatment of 30 mins. Structural characterization of bioplastic was examined using scanning electron microscopy (SEM), mechanical properties using durumeter Shore A, tensile strength and the physical properties using density. SEM evidence on a bioplastic basis. Hardness of bioplastic with addition of nanoclay 5.0% (b/b) and sonication treatment produce bioplastic with maximum hardness properties increased to 76.24 Shore A, tensile strength of 13.5 and Young’s modulus of 47, as well as the added density of 1.238 g/cm3. Nanoclay 7.5% (b/b) upwards will experience decreased hardness and experience agglomerate and debonding.

Preparation and Mechanical Properties of Zein/PVA Nanofibrous Membranes

2012 ◽  
Vol 466-467 ◽  
pp. 391-395
Author(s):  
Feng Xia Liu ◽  
Yong Jia Liu ◽  
Hong Li Cai ◽  
Jia Shuang Luan ◽  
Mei Zhang
Keyword(s):  
Mechanical Properties ◽  
Tensile Testing ◽  
Mechanical Characterization ◽  
Scanning Calorimetry ◽  
Factors Affecting ◽  
Fibrous Membranes ◽  
Dsc Method ◽  
Morphology And Mechanical Properties ◽  
Significant Factors

This paper describes the morphology and mechanical properties of novel electrospun zein based fibrous membranes. From the results, due to adding PVA, it was found that the electrospun fibers of zein can turn into a new strong membrane. The fibrous membranes were characterized by tensile testing, scanning electron microscopy(SEM) and differential scanning calorimetry(DSC). Effect of PVA was analyzed as one of the most significant factors affecting the mechanical characterization of fibrous membranes. The compatibility of zein/PVA nanofibrous were also analyzed by using DSC method.

Microstructural and fractographic characterization of B4C-Al cermets tested under dynamic and static loading

1989 ◽  
Vol 47 ◽  
pp. 562-563
Author(s):  
Gyeung Ho Kim ◽  
Mehmet Sarikaya ◽  
D. L. Milius ◽  
I. A. Aksay
Keyword(s):  
Thin Film ◽  
Mechanical Properties ◽  
Fracture Toughness ◽  
Static Loading ◽  
Carbon Deposition ◽  
Full Density ◽  
Unique Combination ◽  
Strong Component ◽  
Reaction Products

Cermets are designed to optimize the mechanical properties of ceramics (hard and strong component) and metals (ductile and tough component) into one system. However, the processing of such systems is a problem in obtaining fully dense composite without deleterious reaction products. In the lightweight (2.65 g/cc) B4C-Al cermet, many of the processing problems have been circumvented. It is now possible to process fully dense B4C-Al cermet with tailored microstructures and achieve unique combination of mechanical properties (fracture strength of over 600 MPa and fracture toughness of 12 MPa-m1/2). In this paper, microstructure and fractography of B4C-Al cermets, tested under dynamic and static loading conditions, are described.The cermet is prepared by infiltration of Al at 1150°C into partially sintered B4C compact under vacuum to full density. Fracture surface replicas were prepared by using cellulose acetate and thin-film carbon deposition. Samples were observed with a Philips 3000 at 100 kV.

Sign in / Sign up

Export Citation Format

Share Document