scholarly journals Polymerization Behavior and Mechanical Properties of High-Viscosity Bulk Fill and Low Shrinkage Resin Composites

2017 ◽  
Vol 42 (6) ◽  
pp. E177-E187 ◽  
Author(s):  
S Shibasaki ◽  
T Takamizawa ◽  
K Nojiri ◽  
A Imai ◽  
A Tsujimoto ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Flexural Strength ◽  
Resin Composite ◽  
High Viscosity ◽  
The Other ◽  
Light Irradiation ◽  
Volumetric Shrinkage ◽  
Resin Composites ◽  
Polymerization Shrinkage

SUMMARY The present study determined the mechanical properties and volumetric polymerization shrinkage of different categories of resin composite. Three high viscosity bulk fill resin composites were tested: Tetric EvoCeram Bulk Fill (TB, Ivoclar Vivadent), Filtek Bulk Fill posterior restorative (FB, 3M ESPE), and Sonic Fill (SF, Kerr Corp). Two low-shrinkage resin composites, Kalore (KL, GC Corp) and Filtek LS Posterior (LS, 3M ESPE), were used. Three conventional resin composites, Herculite Ultra (HU, Kerr Corp), Estelite ∑ Quick (EQ, Tokuyama Dental), and Filtek Supreme Ultra (SU, 3M ESPE), were used as comparison materials. Following ISO Specification 4049, six specimens for each resin composite were used to determine flexural strength, elastic modulus, and resilience. Volumetric polymerization shrinkage was determined using a water-filled dilatometer. Data were evaluated using analysis of variance followed by Tukey's honestly significant difference test (α=0.05). The flexural strength of the resin composites ranged from 115.4 to 148.1 MPa, the elastic modulus ranged from 5.6 to 13.4 GPa, and the resilience ranged from 0.70 to 1.0 MJ/m3. There were significant differences in flexural properties between the materials but no clear outliers. Volumetric changes as a function of time over a duration of 180 seconds depended on the type of resin composite. However, for all the resin composites, apart from LS, volumetric shrinkage began soon after the start of light irradiation, and a rapid decrease in volume during light irradiation followed by a slower decrease was observed. The low shrinkage resin composites KL and LS showed significantly lower volumetric shrinkage than the other tested materials at the measuring point of 180 seconds. In contrast, the three bulk fill resin composites showed higher volumetric change than the other resin composites. The findings from this study provide clinicians with valuable information regarding the mechanical properties and polymerization kinetics of these categories of current resin composite.

scholarly journals Influence of Different Concentration and Ratio of a Photoinitiator System on the Properties of Experimental Resin Composites

2017 ◽  
Vol 28 (6) ◽  
pp. 726-730 ◽  
Author(s):  
Caio Vinícius Signorelli Grohmann ◽  
Eveline Freitas Soares ◽  
Eduardo José Carvalho Souza-Junior ◽  
William Cunha Brandt ◽  
Regina Maria Puppin-Rontani ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Flexural Strength ◽  
Tertiary Amine ◽  
Water Sorption ◽  
Water Solubility ◽  
Distilled Water ◽  
Resin Composites ◽  
Amine Concentration ◽  
One Way Anova

Abstract The aim in this study was to evaluate the influence of different ratio of camphorquinone/tertiary amine concentration on the flexural strength (FS), elastic modulus (EM), degree of conversion (DC), yellowing (YL), water sorption (WS) and water solubility (WSL) of experimental composites. Thus, acrylate blends were prepared with different camphorquinone (CQ) and amine (DABE) concentrations and ratios by weight: (CQ/DABE%): 0.4/0.4% (C1), 0.4/0.8% (C2), 0.6/0.6% (C3), 0.6/1.2% (C4), 0.8/0.8% (C5), 0.8/1.6% (C6), 1.0/1.0% (C7), 1.0/2.0% (C8), 1.5/1.5% (C9), 1.5/3.0% (C10). For the FS and EM, rectangular specimens (7x2x1 mm, n=10) were photo-activated by single-peak LED for 20 s and tested at Instron (0.5 mm/min). Then, the same specimens were evaluated by FTIR for DC measurement. For YL, disks (5x2 mm, n=10) were prepared, light-cured for 20 s and evaluated in spectrophotometer using the b aspect of the CIEL*a*b* system. For WS and WSL, the volume of the samples was calculated (mm³). For WS and WSL, composites disks (5x0.5 mm, n=5) were prepared. After desiccation, the specimens were stored in distilled water for 7 days and again desiccated, in order to measure the WS and WSL. Data were submitted to one-way ANOVA and Tukey’s test (5%). The groups C8, C9 and C10 showed higher DC, EM and YL means, compared to other composites. Therefore, the FS and WS values were similar among all groups. Also, C1, C2 and C3 presented higher WSL in 7 days, compared to other composites. In general, higher concentrations of camphorquinone promoted higher physical-mechanical properties; however, inducing higher yellowing effect for the experimental composites

scholarly journals Influence of Filler Loading on the Mechanical Properties of Flowable Resin Composites

Materials ◽  
2020 ◽  
Vol 13 (6) ◽  
pp. 1477 ◽  
Author(s):  
Ioana-Codruţa Mirică ◽  
Gabriel Furtos ◽  
Bogdan Bâldea ◽  
Ondine Lucaciu ◽  
Aranka Ilea ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Flexural Modulus ◽  
Filler Loading ◽  
The Other ◽  
Inorganic Filler ◽  
Resin Composites ◽  
Homogeneous Type ◽  
Sem Images

The aim of this study was to evaluate the correlation between the percent of inorganic filler by weight (wt. %) and by volume (vol. %) of 11 flowable resin composites (FRCs) and their mechanical properties. To establish the correlation, the quantity of inorganic filler was determined by combustion and shape/size analyzed by SEM images. The compressive strength (CS), flexural strength (FS), and flexural modulus (FM) were determined. The CS values were between 182.87-310.38 MPa, the FS values ranged between 59.59 and 96.95 MPa, and the FM values were between 2.34 and 6.23 GPa. The percentage of inorganic filler registered values situated between 52.25 and 69.64 wt. % and 35.35 and 53.50 vol. %. There was a very good correlation between CS, FS, and FM vs. the inorganic filler by wt. % and vol. %. (R2 = 0.8899–0.9483). The highest regression was obtained for the FM values vs. vol. %. SEM images of the tested FRCs showed hybrid inorganic filler for Filtek Supreme XT (A3) and StarFlow (A2) and a homogeneous type of inorganic filler for the other investigated materials. All of the FS values were above 50 MPa, the ISO 4049/2019 limit for FRCs.

scholarly journals Mechanical properties of resin composites containing bioactive glass and experimental nano zinc-silica complex

2021 ◽  
Vol 11 (Suppl. 1) ◽  
pp. 137-142
Author(s):  
Mehmet Gökberkkaan Demirel ◽  
Makbule Tuğba Tunçdemir
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Bioactive Glass ◽  
Resin Composite ◽  
Testing Machine ◽  
Control Sample ◽  
Dental Composite ◽  
Resin Composites ◽  
Nano Zinc

Aim: Secondary caries is an important problem in dental composite restoration, and nanoparticles are commonly added to the structures of resin composites to improve their antimicrobial properties. The aim of this study is to evaluate the mechanical properties of composite materials containing bioactive glass (BAG) and an experimental nano zinc-silica (NZS) complex. Methodology: An experimental resin composite containing 70 wt% filler was produced and used as a control sample. This experimental resin composite was then modified by adding different amounts of BAG (10%), NZS (10%), and both BAG and NZS (10% + 10%). NZS was synthesized in situ by milling zinc and silica to nanoscale level. Compressive strength and flexural strength were investigated using a universal testing machine. Data were analyzed using one-way ANOVA and the Tukey post-hoc test. Results: There were no statistically significant differences in compressive strength caused by the filler amount, but statistically significant changes were found in flexural strength. Although the addition of antimicrobial agents to resin composites reduces their physical properties, this is not a clinically unacceptable limit. Conclusion: NZS exhibits better mechanical properties than does BAG, but both materials can be used safely in restorative materials.   How to cite this article: Tunçdemir MT, Demirel MG. Mechanical properties of resin composites containing bioactive glass and experimental nano zinc-silica complex. Int Dent Res 2021;11(Suppl.1):137-42. https://doi.org/10.5577/intdentres.2021.vol11.suppl1.21   Linguistic Revision: The English in this manuscript has been checked by at least two professional editors, both native speakers of English.  

scholarly journals Simple and Low-Cost Thermal Treatments on Direct Resin Composites for Indirect Use

2019 ◽  
Vol 30 (3) ◽  
pp. 279-284
Author(s):  
Guillermo Grazioli ◽  
Alejandro Francia ◽  
Carlos Enrique Cuevas-Suárez ◽  
Cesar Henrique Zanchi ◽  
Rafael Ratto De Moraes
Keyword(s):  
Elastic Modulus ◽  
Flexural Strength ◽  
Mechanical Performance ◽  
Resin Composite ◽  
Low Cost ◽  
Negative Control ◽  
Control Group ◽  
Thermal Treatments ◽  
Resin Composites ◽  
Thermal Methods

Abstract The aim of this study was to evaluate the influence of three low-cost additional thermal treatments, available in the dental office, on the mechanical, chemical and optical properties of a light-cured resin composite indicated for direct restorations but used as indirect restorative. The direct resin composite TPH3 (Dentsply) was light-polymerized using a light-emitting diode curing unit and submitted to three experimental additional thermal treatments: dry heat at 170 °C for 5 min, autoclave at 121 °C for 6 min, or microwave oven at 450 W for 3 min. The resin composite without any thermal treatment was used as negative control group. An indirect resin composite (Vita CM LC, Vita Zahnfabrik) was tested as a reference. Flexural strength, elastic modulus, microhardness, degree of C=C conversion, roughness before and after simulated toothbrush abrasion, translucency parameter and color difference (ΔE00) were evaluated. Data were analyzed at α=0.05. The indirect resin composite presented lower C=C conversion and mechanical performance. The flexural strength was significantly higher in the dry oven group compared with the control. The roughness was not different among groups before or after brushing, but the thermal treatments caused an increase in C=C conversion, microhardness, and elastic modulus without affecting the translucency parameter or showing visible color alteration (ΔE00<1.8). These results suggest that the use of additional thermal methods of polymerization represents an economical and simple alternative to enhance the mechanical and chemical properties of direct resin composites when used as indirect restoratives.

Influence of Light-polymerization Modes on the Degree of Conversion and Mechanical Properties of Resin Composites: A Comparative Analysis Between a Hybrid and a Nanofilled Composite

10.2341/07-81 ◽  
2008 ◽  
Vol 33 (3) ◽  
pp. 287-293 ◽  
Author(s):  
E. M. da Silva ◽  
L. T. Poskus ◽  
J. G. A. Guimarães
Keyword(s):  
Mechanical Properties ◽  
Comparative Analysis ◽  
Flexural Strength ◽  
Hybrid Composite ◽  
Clinical Relevance ◽  
Flexural Modulus ◽  
Degree Of Conversion ◽  
The Other ◽  
Lower Degree ◽  
Resin Composites

Clinical Relevance The nanofilled composite presented a lower degree of conversion, flexural modulus and flexural strength than the hybrid composite. On the other hand, the two materials had a similar hardness. The light polymerization mode influenced only the degree of conversion and the hardness of composites.

scholarly journals Mechanical properties of bulk-fill versus nanohybrid composites: effect of layer thickness and application protocols

2019 ◽  
Vol 22 (2) ◽  
pp. 234-242
Author(s):  
Aylin Cilingir ◽  
Alev Ozsoy ◽  
Meltem Mert Eren ◽  
Ozge Behram ◽  
Benin Dikmen ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Hybrid Composite ◽  
Resin Composite ◽  
Flexural Modulus ◽  
High Viscosity ◽  
Hybrid Resin ◽  
Low Viscosity ◽  
The Mean

Objective: The objective of this study was to evaluate the compressive strength, flexural strength and flexural modulus of high-viscosity, low-viscosity bulk-fill, and conventional nano-hybrid resin composite materials alone and when covered with nano-hybrid resin composite at different incremental thicknesses on the bulk-fill composites. Materials and Methods: Specimens (N=60) were fabricated from the following materials or their combinations (n=10 per group): a) conventional nano-hybrid composite Z550 (FK), b) high-viscosity bulk-fill composite (Tetric N Ceram-TBF), c) low-viscosity bulk-fill composite SDR (SDR), d) Sonicfill (SF), e) SDR (2 mm)+FK (2 mm), f) SDR (4 mm)+FK (4 mm). After 24 h water storage, compressive strength was measured in a universal testing machine (1 mm/min). Additional specimens (N=40) (25x2x2 mm3) were made from FK, TBF, SDR and SF in order to determine the flexural strength and the flexural modulus, (n=10) and subjected to three-point bending test (0.5 mm/min). Data were analyzed using one-way ANOVA and Tamhane’s T2 post-hoc tests (p<0.05). Results: The mean compressive strength (MPa) of the nano-hybrid composite (FK) was significantly higher (223.8±41.3) than those of the other groups (123±27 - 170±24) (p<0.001). SDR (4 mm)+FK (2 mm) showed significantly higher compressive strength than when covered with 4 mm (143±30) or when used alone (146±11) (p<0.05). The mean flexural strength (159±31) and the flexural modulus of FK (34±7) was significantly higher than that of the high- or low-viscosity bulk-fill composites (p<0.001). The mean flexural strength of SF (132±20) was significantly higher compared to TBF (95±25) (p<0.05). Conclusion: Bulk-fill resin composites demonstrated poorer mechanical properties compared to nano-hybrid composite but similar to that of SF. Increasing the thickness of low-viscosity bulk-fill composite (SDR) from 2 to 4 mm underneath the nano-hybrid composite (FK) can improve the mechanical properties of the bulk-fill composites. KeywordsBulk-fill composites; Compressive strength; Flexural modulus; Flexural strength; Mechanical properties.

scholarly journals Assessment of the Rheological and Mechanical Properties of Geopolymer Concrete Comprising Fly Ash and Fluid Catalytic Cracking Residue as Aluminosilicate Precursor

2021 ◽  
Vol 11 (7) ◽  
pp. 3032
Author(s):  
Tuan Anh Le ◽  
Sinh Hoang Le ◽  
Thuy Ninh Nguyen ◽  
Khoa Tan Nguyen
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Fly Ash ◽  
Flexural Strength ◽  
Catalytic Cracking ◽  
Fluid Catalytic Cracking ◽  
High Alumina ◽  
Geopolymer Concrete ◽  
Sem Images

The use of fluid catalytic cracking (FCC) by-products as aluminosilicate precursors in geopolymer binders has attracted significant interest from researchers in recent years owing to their high alumina and silica contents. Introduced in this study is the use of geopolymer concrete comprising FCC residue combined with fly ash as the requisite source of aluminosilicate. Fly ash was replaced with various FCC residue contents ranging from 0–100% by mass of binder. Results from standard testing methods showed that geopolymer concrete rheological properties such as yield stress and plastic viscosity as well as mechanical properties including compressive strength, flexural strength, and elastic modulus were affected significantly by the FCC residue content. With alkali liquid to geopolymer solid ratios (AL:GS) of 0.4 and 0.5, a reduction in compressive and flexural strength was observed in the case of geopolymer concrete with increasing FCC residue content. On the contrary, geopolymer concrete with increasing FCC residue content exhibited improved strength with an AL:GS ratio of 0.65. Relationships enabling estimation of geopolymer elastic modulus based on compressive strength were investigated. Scanning electron microscope (SEM) images and X-ray diffraction (XRD) patterns revealed that the final product from the geopolymerization process consisting of FCC residue was similar to fly ash-based geopolymer concrete. These observations highlight the potential of FCC residue as an aluminosilicate source for geopolymer products.

scholarly journals Effect of Accelerated Aging on Some Mechanical Properties and Wear of Different Commercial Dental Resin Composites

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2769
Author(s):  
Jonne Oja ◽  
Lippo Lassila ◽  
Pekka K. Vallittu ◽  
Sufyan Garoushi
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Accelerated Aging ◽  
Wear Depth ◽  
Resin Composites ◽  
Expiration Date ◽  
Dental Resin ◽  
Hydrothermal Aging ◽  
Dental Resin Composites

The aim of current in vitro research was to determine the effect of hydrothermal accelerated aging on the mechanical properties and wear of different commercial dental resin composites (RCs). In addition, the effect of expiration date of the composite prior its use was also evaluated. Five commercially available RCs were studied: Conventional RCs (Filtek Supreme XTE, G-aenial Posterior, Denfil, and >3y expired Supreme XTE), bulk-fill RC (Filtek Bulk Fill), and short fiber-reinforced RC (everX Posterior). Three-point flexural test was used for determination of ultimate flexural strength (n = 8). A vickers indenter was used for testing surface microhardness. A wear test was conducted with 15,000 chewing cycles using a dual-axis chewing simulator. Wear pattern was analyzed by a three-dimensional (3D) noncontact optical profilometer. Degree of C=C bond conversion of monomers was determined by FTIR-spectrometry. The specimens were either dry stored for 48 h (37 °C) or boiled (100 °C) for 16 h before testing. Scanning electron microscopy (SEM) was used to evaluate the microstructure of each material. Data were analyzed using ANOVA (p = 0.05). Hydrothermal aging had no significant effects on the surface wear and microhardness of tested RCs (p > 0.05). While flexural strength significantly decreased after aging (p < 0.05), except for G-aenial Posterior, which showed no differences. The lowest average wear depth was found for Filtek Bulk Fill (29 µm) (p < 0.05), while everX Posterior and Denfil showed the highest wear depth values (40, 39 µm) in both conditions. Passing the expiration date for 40 months did not affect the flexural strength and wear of tested RC. SEM demonstrated a significant number of small pits on Denfil’s surface after aging. It was concluded that the effect of accelerated aging may have caused certain weakening of the RC of some brands, whereas no effect was found with one brand of RC. Thus, the accelerated aging appeared to be more dependent on material and tested material property.

Effects of the Mould Pressure and Mould Pressing Time on the Properties of Graphite/Phenolic Resin Composites

2013 ◽  
Vol 706-708 ◽  
pp. 95-98
Author(s):  
Mi Dan Li ◽  
Dong Mei Liu ◽  
Lu Lu Feng ◽  
Huan Niu ◽  
Yao Lu
Keyword(s):  
Mechanical Properties ◽  
Electrical Conductivity ◽  
Flexural Strength ◽  
Polymer Matrix ◽  
Phenolic Resin ◽  
Polymer Matrix Composites ◽  
Resin Composites ◽  
Matrix Composites ◽  
Natural Graphite ◽  
Pressing Time

Polymer matrix composites made from phenolic resin are filled with natural graphite powders. They are fabricated by compression molding technique. The density, electrical conductivity and flexural strength of composite are analyzed to determine the influences of mould pressure and mould pressing time on the physical, electrical and mechanical properties of composite. It is found that the density, electrical conductivity and flexural strength of composites increased with increasing mould pressure. Under pressure of 40 MPa for 60 min, the density, electrical conductivity and flexural strength of composites were 1.85 g/cm3, 4.35  103 S/cm and 70 MPa, respectively. The decreased gaps could be the main reason for the increasing of density, electrical conductivity and flexural strength as mould pressure increases. The results also show that the density of composites increased with increasing mould pressing time.

scholarly journals Mechanical properties, volumetric shrinkage and depth of cure of short fiber-reinforced resin composite

2016 ◽  
Vol 35 (3) ◽  
pp. 418-424 ◽  
Author(s):  
Akimasa TSUJIMOTO ◽  
Wayne W. BARKMEIER ◽  
Toshiki TAKAMIZAWA ◽  
Mark A. LATTA ◽  
Masashi MIYAZAKI
Keyword(s):  
Mechanical Properties ◽  
Resin Composite ◽  
Short Fiber ◽  
Volumetric Shrinkage ◽  
Fiber Reinforced ◽  
Depth Of Cure
Sign in / Sign up

Export Citation Format

Share Document