scholarly journals Influence of Chlorhexidine and/or Ethanol Treatment on Bond Strength of an Etch-and-rinse Adhesive to Dentin: An In Vitro and In Situ Study

2014 ◽  
Vol 39 (1) ◽  
pp. 64-71 ◽  
Author(s):  
DMS Simões ◽  
RT Basting ◽  
FLB Amaral ◽  
CP Turssi ◽  
FMG França
Keyword(s):  
Bond Strength ◽  
Resin Composite ◽  
Adhesive System ◽  
Dentin Surface ◽  
In Vitro Aging ◽  
Etch And Rinse ◽  
Bond Interface ◽  
Vitro Model

SUMMARY The aim of this study was to evaluate the effect of a chlorhexidine and/or ethanol application on the bond strength of an etch-and-rinse, hydrophobic adhesive system either under in vitro aging or in situ cariogenic challenge. The dentin surface of 36 human third molars were flattened and allocated into four groups to be treated with chlorhexidine, ethanol, or chlorhexidine + ethanol or left unexposed to any solution (control) (n=9). Then, a resin composite restoration was made on the dentin surface and longitudinal sticks were obtained. Sticks from each tooth were assigned to three test conditions: stored in water in vitro for 24 hours, stored in water in vitro for 6 months, or worn in situ for 14 days. During in situ wear time, a high-cariogenic challenge condition was simulated. Specimens were tested for microtensile bond strength (μTBS). Multivariate analysis of variance and Tukey's test showed that chlorhexidine, ethanol, or chlorhexidine + ethanol did not affect the μTBS. The in vitro μTBS values were significantly lower for the specimens stored for 6 months than for those stored for 24 hours. Intermediate μTBS values were shown by the specimens worn in situ. Thus, use of chlorhexidine and/or ethanol was incapable of containing the degradation at the bond interface in the in vitro model. The in situ model was capable of reducing bond strength similarly to the in vitro/6 months model. Despite this, the in situ bond strength was still similar to that of the in vitro/24-hour model.

scholarly journals In Vivo and In Vitro Effects of Chlorhexidine Pretreatment on Immediate and Aged Dentin Bond Strengths

2016 ◽  
Vol 41 (3) ◽  
pp. 258-267 ◽  
Author(s):  
Z Gunaydin ◽  
AR Yazici ◽  
ZC Cehreli
Keyword(s):  
Bond Strength ◽  
Resin Composite ◽  
Adhesive System ◽  
Etch And Rinse ◽  
Bonferroni Test ◽  
Bond Strengths ◽  
In Vitro Effects ◽  
Self Etch

SUMMARY This study evaluated the effect of 2% chlorhexidine (CHX) pretreatment of dentin on the immediate and aged microtensile bond strength (μTBS) of different adhesives to dentin in vivo and in vitro. Class I cavities were prepared in 80 caries-free human third molars of 40 patients in a split-mouth fashion. In each tooth pair, one tooth received 2% CHX pretreatment after which both teeth were randomly assigned to one of the following groups with respect to the type of adhesive system applied: Adper Single Bond 2 (etch-and-rinse), Clearfil SE Bond (two-step self-etch), Clearfil S3 Bond (one-step self-etch), and Adper Prompt-L-Pop (all-in-one self-etch). The teeth were restored with resin composite and extracted for μTBS testing either immediately or after six months in function. In vitro specimen pairs were prepared as with the clinical protocol in intact, freshly extracted human molars, and thereafter, subjected to testing immediately or after 5000× thermocycling. Data were analyzed with four-way analysis of variance (ANOVA). Bonferroni test was utilized for pair-wise comparisons. The immediate bond strength values were significantly higher than “aged” ones for all tested adhesives (p=0.00). The in vitro immediate bond strength values were statistically higher than in vivo bond strength values (p<0.05). While the bond strength of in vitro aged, CHX-treated samples were higher than their in vivo counterparts (p<0.05), no difference was observed in non-CHX treated groups (p>0.05). In the absence of CHX pretreatment, all adhesives showed significantly higher immediate bond strength values than CHX-treated groups, while all “aged”, non-pretreated adhesives exhibited significantly lower bond strength values (both p<0.05). By contrast, chlorhexidine pretreatment resulted in significantly higher aged bond strengths, regardless of the adhesive system and testing condition. Aging-associated decline in dentin bond strength of etch-and rinse and self-etch adhesives can be counteracted by chlorhexidine application.

Effect of Baicalein on Matrix Metalloproteinases and Durability of Resin-Dentin Bonding

2018 ◽  
Vol 43 (4) ◽  
pp. 426-436 ◽  
Author(s):  
J Li ◽  
B Chen ◽  
N Hong ◽  
S Wu ◽  
Y Li
Keyword(s):  
Matrix Metalloproteinases ◽  
Bonding Strength ◽  
Resin Composite ◽  
Artificial Saliva ◽  
Adhesive System ◽  
Inhibitory Effect ◽  
Dentin Bonding ◽  
Microtensile Testing ◽  
Etch And Rinse

SUMMARY Objective: In an attempt to increase resin-dentin bonding quality, this study used baicalein as a preconditioner in an etch-and-rinse adhesive to evaluate its effect on matrix metalloproteinases (MMPs) and adhesive durability. Methods: As a MMP inhibitor and potential collagen cross-linking agent, baicalein was used as a preconditioner in an etch-and-rinse adhesive system. The degree of conversion was evaluated by Fourier-transform infrared spectroscopy. EnzChek gelatinase/collagenase assay kits were then used to detect the MMP inhibitory effect of different concentrations of baicalein (0.1, 0.5, 2.5, and 5.0 μg/mL) on dentin powders. During in vitro bonding procedures, flat dentin surfaces on sound third molars were preconditioned with 2.5 μg/mL baicalein after being acid-etched; this step was followed by continuation of adhesive processes and build-up of resin composite. After resin-dentin stick preparation, bonding strength, failure mode, and interface nanoleakage were respectively evaluated via microtensile testing, stereomicroscopy, and field emission scanning electron microscopy either immediately or after storage in artificial saliva for three or six months. Data were analyzed by two-way analysis of variance and Tukey test (α=0.05). Results: Baicalein at a concentration of 0-5.0 μg/mL did not influence the conversion of adhesives. However, it inhibited the activities of dentin-bond gelatinase and collagenase, especially at a concentration of 2.5 μg/mL, while effectively increasing microtensile bonding strength and decreasing nanoleakage in vitro, both immediately and after aging. Conclusions: Baicalein used as preconditioner in an etch-and-rinse adhesive system has an anti-MMP function and effectively improves resin-dentin bonding durability in vitro, which has potential value in clinical bonding procedures.

scholarly journals Chitosan in different concentrations added to a two-step etch-and-rinse adhesive system: influence on bond strength to dentin

2017 ◽  
Vol 20 (4) ◽  
pp. 55
Author(s):  
Rafael Avellar de Carvalho Nunes ◽  
Flávia Lucisano Botelho do Amaral ◽  
Fabiana Mantovani Gomes França ◽  
Cecilia Pedroso Turssi ◽  
Roberta Tarkany Basting
Keyword(s):  
Bond Strength ◽  
Failure Mode ◽  
Failure Modes ◽  
Resin Composite ◽  
Adhesive System ◽  
Fracture Pattern ◽  
Test Machine ◽  
Microtensile Bond Strength ◽  
Etch And Rinse ◽  
Strength Tests

<p class="Corpo"><strong>Objective</strong>: the aim of the present study was to evaluate the influence of adding different concentrations of chitosan to an experimental two-step etch-and-rinse adhesive system on the bond strength and failure mode to dentin. <strong>Material</strong> <strong>and</strong> <strong>Methods</strong>: thirty-two flat dentin surfaces were obtained from extracted human third molars and divided into four groups  (n=8) for application of the adhesive systems: AD - conventional two-step adhesive system (Adper Single Bond 2); EXP – experimental two-step etch-and-rinse adhesive system; Chi0.2% - EXP with addition of 0.2% Chitosan; Chi0.5% - EXP with addition of 0.5% Chitosan. Resin composite build-ups were made and the composite/dentin specimens were sectioned to obtain rectangular beams with a bond area of approximately 1mm<sup>2</sup>. After 24 hours, the sticks were submitted to microtensile bond strength tests in a universal test machine. The fracture pattern was evaluated under a stereoscopic loupe at 40X magnification. <strong>Results</strong>: one-way analysis of variance showed that the type of adhesive system had no significant effect on the bond strength values (p = 0.142), showing the mean bond strength values (standard deviation), in MPa, for the groups as follows: AD=20.1 (5.4); EXP=16.6 (2.3); Chi0.2%=16.1 (2.8); Chi0.5%=16.9 (2.3). In all the groups there was predominance of cohesive fractures in dentin, representing 68 to 82% of the failure modes. <strong>Conclusion</strong>: the addition of 0.2 or 0.5% of chitosan had no influence on the bond strength and failure mode of an experimental two-step etch-and-rinse adhesive system to dentin.</p><p class="Corpo"><strong>Keywords</strong></p><p class="Corpo">Chitosan; Dental Adhesives; Failure Mode; Microtensile Bond Strength.</p>

scholarly journals The Effect of Biodentine Maturation Time on Resin Bond Strength When Aged in Artificial Saliva

2020 ◽  
Vol 2020 ◽  
pp. 1-7
Author(s):  
Ruba M. Mustafa ◽  
Suhad J. Al-Nasrawi ◽  
Abtesam I. Aljdaimi
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Resin Composite ◽  
Artificial Saliva ◽  
Adhesive System ◽  
Failure Patterns ◽  
Etch And Rinse ◽  
Significant Difference ◽  
Post Hoc ◽  
Composite Restoration

Biodentine is a calcium silicate cement (CSC) that has been broadly applied in vital pulp therapy. The quality of the Biodentine-composite bond has a significant effect on the longevity of the definitive restoration. The aim of this study is to investigate the shear bond strength (SBS) between Biodentine and composite restoration at different maturation times of Biodentine aged in artificial saliva. Fifteen Biodentine discs were allocated into three groups (n = 5) based on the timeframe of performance of composite restoration: immediate (after 12  min), after 14 days, and after 28 days of Biodentine maturation. Total etch and rinse adhesive system and bulk-fill regular resin composite were used. The shear bond strength and the failure pattern were assessed. One-way ANOVA with the Bonferroni post hoc test was applied for statistical analysis at p < 0.05 . The highest (32.47 ± 8.18 MPa) and the lowest (4.08 ± 0.81 MPa) SBS values were recorded for 14 days and 12 min groups, respectively. Significant statistical differences were reported among the groups, and a high statistically significant difference was found between the immediate group and the other groups. Adhesive failure patterns were evident in all groups. More clinically acceptable bond strength between the Biodentine and overlaid composite restoration is at 14 days after Biodentine maturation. Delaying the coverage of Biodentine later than 14 days may significantly reduce the SBS. Using the artificial saliva as an aging medium may affect the SBS between Biodentine and composite material.

scholarly journals Effect of tooth age on bond strength to dentin

2003 ◽  
Vol 11 (4) ◽  
pp. 342-347 ◽  
Author(s):  
Marcelo Giannini ◽  
Patrícia Chaves ◽  
Marcelo Tavares de Oliveira
Keyword(s):  
Bond Strength ◽  
Resin Composite ◽  
Testing Machine ◽  
Age Groups ◽  
In Vitro Study ◽  
Adhesive System ◽  
Tensile Bond Strength ◽  
Significant Difference ◽  
Diamond Saw

This in vitro study evaluated the effect of tooth age on the tensile bond strength of Prime & Bond NT adhesive system to dentin. Human third molars from the five age groups were analyzed: A- 17 to 20yrs, B- 21 to 30yrs, C- 31 to 40yrs, D- 41 to 50yrs and E- 51 to 63yrs. The occlusal enamel was removed using a diamond saw under water cooling and the dentin surface was wet-ground with 600-grit SiC paper to obtain flat surfaces. The adhesive system was applied according to the manufacturer's instructions and a 6-mm high resin "crown" was built-up with resin composite. Teeth were stored for 24 hours in distilled water at 37ºC and prepared for micro-tensile testing. Each specimen was mounted in a testing jig attached to a universal testing machine and stressed in tension at a crosshead speed of 0.5mm/min until failure. The means of tensile bond strength were (MPa): A- 21.42 ± 7.52ª; B- 30.13 ± 10.19ª; C- 31.69 ± 11.78ª; D- 30.69 ± 8.47ª and E- 35.66 ± 9.54ª. No statistically significant difference was observed among the age groups (p > 0.05). The results suggested that the tensile bond strength of the adhesive system was not significantly affected by dentin aging.

scholarly journals Influence of Dentin Priming with Tannin-Rich Plant Extracts on the Longevity of Bonded Composite Restorations

2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Mackeler Ramos Polassi ◽  
Thales de Sá Oliveira ◽  
Ana Calheiros de Carvalho ◽  
Lívia Soman de Medeiros Medeiros ◽  
Thiago André Moura Veiga ◽  
...  
Keyword(s):  
Contact Angle ◽  
Bond Strength ◽  
Plant Extracts ◽  
In Vitro Study ◽  
Adhesive System ◽  
Contact Angles ◽  
Control Group ◽  
Dentin Surface ◽  
Rhus Chinensis

Objective. This in vitro study evaluated the influence of bioactive plant extracts as dentin biomodifying agents to improve the longevity of bonded restorations. For that, plant extracts were applied to the dentin surface prior to the adhesive system. Materials and Methods. Bovine incisors were ground flat to obtain 2 mm thick slices in which conical preparations were made (N = 10). Tannin-containing plant extracts were applied to dentin before the application of the restorative system, as follows: control group (untreated, CTL), chlorhexidine 0.12% (CHX), mastruz (Dysphania ambrosioides, MTZ), cat’s claw (Uncaria tomentosa, CTC), guarana (Paullinia cupana, GUA), galla chinensis (Rhus chinensis, GCH), and tannic acid (extracted from Acacia decurrens, TNA). The push-out bond strength test was conducted (0.5 mm/min). Dentin biomodification was assessed by the modulus of elasticity and mass change in bovine tooth sections (0.5 × 1.7 × 7.0 mm). The dentin staining after extract treatments of dentin slices was compared. The dentin surface wettability was also evaluated by means of the contact angles of the adhesive system with the dentin surface and compared with the untreated control group. Data were subjected to ANOVA/Tukey’s test (α = 0.05). Results. The bond strength of the restoratives to dentin was not significantly improved by the plant extracts, irrespective of the evaluation time ( p > 0.05 ). Except for TNA, the elastic modulus of demineralized dentin significantly reduced after treatment with the plant extracts ( p < 0.05 ). The dentin staining correlated with the tannin content of the extracts. The contact angle was significantly reduced when treated with CTC, GCH, and TNA. Conclusions. The tannin-containing extracts had a questionable effect on the longevity of bonded restorations. The dentin modulus was negatively affected by the extract treatments. Although some of the extracts changed the contact angle, which seems to improve the adhesive monomer permeation, the tannin-rich plant extract application prior to adhesive application was proven to be clinically unfeasible due to dentin staining.

scholarly journals Bond strength of universal adhesive applied to dry and wet dentin

2020 ◽  
Vol 19 ◽  
pp. e201662
Author(s):  
Maria Luísa de Alencar e Silva Leite ◽  
Caroline de Farias Charamba ◽  
Renally Bezerra Wanderley e Lima ◽  
Sônia Saeger Meireles ◽  
Rosângela Marques Duarte ◽  
...  
Keyword(s):  
Bond Strength ◽  
Storage Time ◽  
Resin Composite ◽  
Adhesive System ◽  
Microtensile Bond Strength ◽  
Universal Adhesive ◽  
Bonding Quality ◽  
Etch And Rinse ◽  
Significant Difference ◽  
One Year

Aim: This study evaluated the influence of dentin wettability on the immediate and extended microtensile bond strength (mTBS) of a universal adhesive system used in the etch-and-rinse strategy. Methods: Twenty human third molars were selected and divided into four groups according to the adhesive system and dentin wettability. The mTBS values of each group were registered 24 h and one year after adhesive system application and resin composite block build-up (n=30). Data were analyzed by the t-test (p<0.05). Results: When both adhesive systems were compared, there was no statistically significant difference when they were applied following wet bonding (p>0.05). However, the dry bonding reduced μTBS values of the Adper Single Bond 2 adhesive (p<0.05). Regarding storage time, both groups presented similar μTBS values at 24 h and one year (p>0.05). Conclusions: Therefore, the Scotchbond Universal Adhesive can be applied to dry or wet dentin without compromising the etch-and-rinse bonding quality and the durability of the restorations.

scholarly journals Effects of Different Cavity Disinfectants on Shear Bond Strength of a Silorane-based Resin Composite

2011 ◽  
Vol 12 (4) ◽  
pp. 279-286 ◽  
Author(s):  
Soley Arslan ◽  
A Ruya Yazici ◽  
Jale Gorucu ◽  
Atilla Ertan ◽  
KanŞad Pala ◽  
...  
Keyword(s):  
Bond Strength ◽  
Sodium Hypochlorite ◽  
Shear Bond Strength ◽  
Resin Composite ◽  
Acrylic Resin ◽  
Adhesive System ◽  
Shear Mode ◽  
Significant Difference ◽  
Wet Ground

ABSTRACT Aim This in vitro study evaluated the effect of different cavity disinfection agents on bond strength of a silorane-based resin composite. Materials and methods Thirty-six caries-free human third mandibular molars sectioned in mesio-distal direction were mounted in acrylic resin with their flat dentin surfaces exposed. After the dentin surfaces were wet ground with # 600 silicon carbide paper, the teeth were randomly divided into 6 groups of 12 each according to the cavity disinfection agents; chlorhexidine (CHX); sodium hypochlorite (NaOCl), propolis, ozone, Er, Cr:YSGG laser and no treatment (control). After treatment of dentin surfaces with one of these cavity disinfection agents, Filtek Silorane adhesive system was applied. The silorane-based resin composite, Filtek Silorane was condensed into a mold and polymerized. After storage at 37°C for 24 hours, the specimens were tested in shear mode at a crosshead speed of 1.0 mm/minute. The results were analyzed by one-way ANOVA. Results No statistically significant difference was observed between the groups (p>0.05). Conclusion The use of the tested cavity disinfection agents, chlorhexidine, sodium hypochlorite, propolis, ozone and Er, Cr:YSGG laser did not significantly affect the dentin bond strength of a silorane-based resin composite, Filtek Silorane. Clinical significance Cavity disinfectant applications did not affect the dentin bond strength of a silorane-based resin composite. How to cite this article Arslan S, Yazici AR, Gorucu J, Ertan A, Pala K, Üstün Y, Antonson SA, Antonson DE. Effects of Different Cavity Disinfectants on Shear Bond Strength of a Siloranebased Resin Composite. J Contemp Dent Pract 2011;12(4): 279-286.

scholarly journals Microtensile Bond Strength of Etch-and-Rinse Adhesives in Different Hydroabrasion Conditionings

2021 ◽  
Vol 2021 ◽  
pp. 1-8
Author(s):  
Michele Tepedino ◽  
Maciej Iancu Potrubacz ◽  
Antonella Imperiale ◽  
Claudio Chimenti ◽  
Mario Capogreco ◽  
...  
Keyword(s):  
Bond Strength ◽  
Adhesive System ◽  
Mode Analysis ◽  
Microtensile Bond Strength ◽  
Cavity Preparation ◽  
Etch And Rinse ◽  
Failure Mode Analysis ◽  
Bond Strengths ◽  
Dentin Conditioning

The aim of the present study was to in vitro evaluate the effect of dentin conditioning with hydroabrasion on the microtensile bond strengths of three adhesive systems, compared to the standard etch-and-rinse technique. Sixty extracted human third molars were collected, and their midcoronal occlusal dentin was used for the microtensile bond strength test. Teeth were randomly assigned to three groups according to the adhesive system used: ExciTE F DSC, ENA Bond, and Scotchbond Universal. Specimens from each group were further divided into four subgroups: control specimens were treated with standard adhesive procedures; hydroabraded (HA) specimens were subjected to preventive hydroabrasion with three different intensity levels. After bonding procedures, composite crowns were incrementally built up. After thermocycling, specimens were subsequently sectioned into 1 × 1 mm sticks, and microtensile bond strengths were measured. Data were statistically analyzed. Failure mode analysis was performed. There were no significant differences in terms of bond strength between standard adhesion protocols and adhesion with HA preconditionings. On the other hand, the type of adhesive used had a significant effect on the tensile bond strength. Subgroups treated with hydroabrasion at higher intensity showed a slightly increased frequency of cohesive fractures. In conclusion, hydroabrasion can be used for dentin cavity preparation or finishing, since it does not seem to affect the bonding effectiveness.

scholarly journals Tensile Bond Strengths of Two Adhesives on Irradiated and Nonirradiated Human Dentin

2015 ◽  
Vol 2015 ◽  
pp. 1-6 ◽  
Author(s):  
Cécile Bernard ◽  
Cyril Villat ◽  
Hazem Abouelleil ◽  
Marie-Paule Gustin ◽  
Brigitte Grosgogeat
Keyword(s):  
Bond Strength ◽  
Adhesive System ◽  
Adhesive Systems ◽  
Etch And Rinse ◽  
Human Dentin ◽  
Nanohybrid Composite ◽  
Nonparametric Statistical ◽  
Self Etch

The aim of this study was to assess the effect of radiotherapy on bond efficiency of two different adhesive systems using tensile bond strength test. Twenty extracted teeth after radiotherapy and twenty nonirradiated extracted teeth were used. The irradiation was appliedin vivoto a minimal dose of 50 Gy. The specimens of each group were randomly assigned to two subgroups to test two different adhesive systems. A three-step/etch-and-rinse adhesive system (Optibond FL) and a two-steps/self-etch adhesive system (Optibond XTR) were used. Composite buildups were performed with a nanohybrid composite (Herculite XTR). All specimens were submitted to thermocycling ageing (10000 cycles). The specimens were sectioned in 1 mm2sticks. Microtensile bond strength tests were measured. Nonparametric statistical analyses were performed due to nonnormality of data. Optibond XTR on irradiated and nonirradiated teeth did not show any significant differences. However, Optibond FL bond strength was more effective on nonirradiated teeth than on irradiated teeth. Within the limitations of anin vitrostudy, it can be concluded that radiotherapy had a significant detrimental effect on bond strength to human dentin. However, it seems that adhesive choice could be adapted to the substrata. According to the present study, the two-steps/self-etch (Optibond XTR) adhesive system tested could be more effective on irradiated dentin compared to three-steps/etch-and-rinse adhesive system (Optibond FL).

Sign in / Sign up

Export Citation Format

Share Document