scholarly journals PART I.EFFECT OF SURFACE AREA AND OIL ABSORPTION OF CARBON BLACK ON PROPERTIES OF NATURAL RUBBER COMPOUND.

1964 ◽  
Vol 37 (4) ◽  
pp. 265-272
Author(s):  
S. Ando ◽  
J. Yamada ◽  
K. Hayashi ◽  
Y. Akiyama ◽  
T. Shinmyo
Keyword(s):  
Carbon Black ◽  
Natural Rubber ◽  
Surface Area ◽  
Oil Absorption ◽  
Rubber Compound

The Effect of Carbon Black Type on the Dynamic Properties of Natural Rubber

1973 ◽  
Vol 46 (4) ◽  
pp. 897-926 ◽  
Author(s):  
J. D. Ulmer ◽  
V. E. Chirico ◽  
C. E. Scott
Keyword(s):  
Carbon Black ◽  
Natural Rubber ◽  
Surface Area ◽  
Strain Amplitude ◽  
Dynamic Properties ◽  
Dynamic Strain ◽  
Rubber Compound ◽  
Wide Range ◽  
Frequency Interaction ◽  
Different Temperatures

Abstract The influence of carbon black type on the dynamic properties of natural rubber is examined for nine carbon blacks, encompassing a wide range of structure and surface area. The dynamic properties are measured at 23° C and 100° C, over a 2 decade range of log frequency, and over a range of 1 to 25 per cent dynamic strain. The effect of carbon black structure and surface area on dynamic properties of a natural rubber compound are dependent on the combination of strain amplitude and frequency test conditions. The effect of carbon black surface area and structure at different temperatures varies on an absolute basis but not necessarily on a relative basis. Correlations of forced non resonant measurements of dynamic properties with dynamic measurements using other instruments confirms the strain amplitude and frequency interaction with carbon black type. Also, the Goodyear-Healy Rebound machine, the Goodrich Flexometer, and the Pirelli Hysteresimeter can be used to estimate basic dynamic properties over limited strain amplitude and frequency conditions. In addition, mixing procedure was found to have a significant effect on the dynamic properties of a natural rubber compound filled with N-327.

Influence of N-Phenyl-p-Phenylenediamine Modified Epoxidized Palm Oil on Properties of Carbon Black Filled Natural Rubber Compound and Vulcanizate

2013 ◽  
Vol 844 ◽  
pp. 239-242 ◽  
Author(s):  
Supaporn Ieadsang ◽  
Anoma Thitithammawong ◽  
Charoen Nakason ◽  
Azizon Kaesaman
Keyword(s):  
Carbon Black ◽  
Natural Rubber ◽  
Palm Oil ◽  
Morphological Properties ◽  
Rubber Compound ◽  
Mixing Energy ◽  
Epoxidized Palm Oil ◽  
Curing Characteristics ◽  
Polycyclic Aromatic ◽  
Ft Ir

Modified epoxidized palm oil (pA-m-EPO) was prepared by a reaction of epoxidized palm oil (EPO) with n-phenyl-p-phenylenediamine. Chemical structure of the pA-m-EPO was characterized by using FT-IR spectrophotometer. Influence of the pA-m-EPO on bound rubber content, total mixing energy, Mooney viscosity and curing characteristics of carbon black filled natural rubber compound together with mechanical and morphological properties of carbon black filled natural rubber vulcanizates was later studied. Results showed that the NR compound and vulcanizate with using the pA-m-EPO gave inferior properties than those of using the aromatic oil. However, they provided better properties than those of the treated distillate aromatic extract (TDAE) excepting filler dispersion. Furthermore, the pA-m-EPO can be claimed as non-carcinogenic processing oil with low polycyclic aromatic hydrocarbons.

scholarly journals Synergistic effect by high specific surface area carbon black as secondary filler in silica reinforced natural rubber tire tread compounds

2020 ◽  
Vol 81 ◽  
pp. 106173 ◽  
Author(s):  
Suppachai Sattayanurak ◽  
Kannika Sahakaro ◽  
Wisut Kaewsakul ◽  
Wilma K. Dierkes ◽  
Louis A.E.M. Reuvekamp ◽  
...  
Keyword(s):  
Carbon Black ◽  
Synergistic Effect ◽  
Natural Rubber ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
High Specific Surface Area ◽  
Rubber Tire

Characterization of Snap-On Calf Nipple Product and Development of its Compound Formulation Based on Natural Rubber

2017 ◽  
Vol 744 ◽  
pp. 282-287
Author(s):  
Sarawut Prasertsri ◽  
Sansanee Srichan
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Calcium Carbonate ◽  
Carbon Black ◽  
Natural Rubber ◽  
Soxhlet Extraction ◽  
Rubber Compound ◽  
Rubber Compounds ◽  
Rubber Component

This research aimed to develop the formulation of natural rubber filled with carbon black, silica and calcium carbonate for rubber calf nipple application. The reverse engineering was performed on the calf nipple product to analyze the rubber type and component by using Soxhlet extraction, thermogravimetric analysis (TGA) and Fourier transform infrared spectroscopy (FTIR) techniques. Furthermore, mechanical properties were examined to act as benchmark for the rubber compound design. The results showed that rubber component in the nipple product was natural rubber, whereas two filler types revealed as carbon black and calcium carbonate with 10 and 35 of the total weight. In addition, rubber nipple showed the hardness of 46±1 Shore A and tensile strength of 5.3±0.60 MPa. From the investigation of the properties of developed rubber compounds in this work, it was found that the mechanical properties depended on type and content of filler. The required mechanical properties of vulcanizates were achieved at 20 phr of carbon black (N330), 20 phr of silica and 120 phr of calcium carbonate.

scholarly journals Influence of Carbon Black and Silica Filler on the Rheological and Mechanical Properties of Natural Rubber Compound

2015 ◽  
Vol 16 ◽  
pp. 258-264 ◽  
Author(s):  
Ika Maria Ulfah ◽  
Riastuti Fidyaningsih ◽  
Sri Rahayu ◽  
Diah Ayu Fitriani ◽  
Dita Adi Saputra ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Black ◽  
Natural Rubber ◽  
Rubber Compound ◽  
Silica Filler

scholarly journals Natural Rubber/High Cis Butadiene Rubber-Filler Interactions And Rheological Properties In Rubber Airbag Compounding Formulation

2019 ◽  
Vol 1 (1) ◽  
pp. 16-20
Author(s):  
Ade Sholeh Hidayat ◽  
Dewi Kusuma Arti ◽  
Lies Agustine ◽  
Mahendra Aggaravidya
Keyword(s):  
Mechanical Properties ◽  
Carbon Black ◽  
Natural Rubber ◽  
Rheological Properties ◽  
High Strain ◽  
Butadiene Rubber ◽  
Rubber Compound ◽  
General Application ◽  
Optimum Formulation ◽  
Strain Sweep

The rheological properties of rubber compound in general application and especially rubber airbag compounding is very important to predict the mechanical properties of rubber products, as well as useful for obtaining optimum formulations in the research and development of a product. The viscoelastic properties of the rubber compound are strongly influenced by the type of rubber and the filler used. The purpose of this research is to investigate the rheological properties of rubber airbag compounding using natural rubber (NR) and high cis butadiene rubber (BR) materials with various compositions of carbon black N220 filler. The mixing of NR and BR with 90/10 phr ratio was performed in a kneader, with carbon black N220 filler variation: 35, 45, 50 phr, named as BD1, BD2 and BD3, respectively. Rheology and viscosity properties were tested using Rubber Process Analyser (RPA) 2000 Alpha Technology. The test was performed with strain sweep at 70 C and comparing 1% strain and 10% strain to indicate dispersion and homogenity. Frequency sweep was performed at 100 C at 6 cpm and 7% strain.  High strain sweep was also done as well as strain sweep after cure (ASTM D6601) which material were cured at 1800 C and strain sweep was applied at 1%, 2%, 5%, 10% and 20% to determine the mechanical properties of compound. The result showed that 35 phr of carbon black N220 (BD1) was the optimum formulation since compounds BD3 and BD2 have higher elastic torque (S’) peaks and may be harder to process as a result. The results for Tan (Delta) from all compounds in the high strain sweep verify that compounds BD3 and BD2 have lower Tan(Delta) values and therefore will probably have more difficulty in processing. The highest peak of modulus values at low strain indicates the carbon black with the highest reinforcement or the worst dispersion. BD3 and BD2 have high peak modulus value which is show the worse dispersion compared to BD1. Keywords: rheology, rubber airbag, filler, RPA

Plasma Polymerized Primers for Rubber to Metal Bonding: Characterization of the Interphase

1995 ◽  
Vol 385 ◽  
Author(s):  
Y. M. Tsai ◽  
F. J. Boerio ◽  
Dong K. Kim
Keyword(s):  
Zinc Oxide ◽  
Free Radicals ◽  
Carbon Black ◽  
Stearic Acid ◽  
Natural Rubber ◽  
Rubber Compound ◽  
Carbonyl Groups ◽  
Double Bonds ◽  
Metal Bonding

ABSTRACTPlasma polymerized acetylene films contained mono- and di-substituted acetylene groups, aromatic groups, and carbonyl groups which resulted from reaction of residual free radicals with oxygen when the films were exposed to the atmosphere. There was some evidence for formation of acetylides in the interphase between the films and the substrates. Reactions occurring in the interphase between the plasma polymerized films and natural rubber were simulated using a model rubber compound consisting of a mixture of squalene, zinc oxide, carbon black, sulfur, stearic acid, diaryl-p-diphenyleneamine, and N,N-dicyclohexylbenzothiazole sulfenamide (DCBS). Zinc oxide and cobalt naphthenate reacted with stearic acid to form zinc and cobalt stearates. The stearates reacted with the benzothiazole sulfonamide moiety of DCBS and with sulfur to form zinc and cobalt accelerator complexes and perthiomercaptides. The complexes and perthiomercaptides reacted with squalene and the plasma polymer to form pendant groups which eventually disproportionated to form crosslinks between squalene and the primer. Migration of double bonds during reaction of the model rubber compound with the films resulted in formation of conjugated double bonds in squalene.

Silica Properties/Rubber Performance Correlation. Carbon Black-Filled Rubber Compounds

1994 ◽  
Vol 67 (2) ◽  
pp. 217-236 ◽  
Author(s):  
Timothy A. Okel ◽  
Walter H. Waddell
Keyword(s):  
Carbon Black ◽  
Physical Properties ◽  
Surface Area ◽  
Performance Characteristics ◽  
Rubber Compound ◽  
The Road ◽  
Precipitated Silica ◽  
Filled Rubber ◽  
Rubber Compounds ◽  
As Stress

Abstract The effectiveness of predicting rubber performance based on measured silica physical properties in silica- and carbon black-filled compounds is presented for three rubber formulations: an off-the-road tire tread, a wire coat stock and a V-belt. Correlation and regression analyses were performed using SAS software for sixteen physical properties of thirteen precipitated silicas, and sixteen rubber compound performance characteristics of the three compounds. Silica physical properties studied include various measurements of surface area and structure, particle size, pH and impurities. Rubber performance characteristics studied include cure properties and physical properties such as stress/strain, tear strength, cut growth resistance, abrasion resistance and heat build-up. The present study confirms that silica surface area is the single best predictor of the effect that varying silica physical properties have on the physical performance of cured, carbon black-filled rubber compounds containing precipitated silica. Silica structure, as measured by DBP absorption and nitrogen or mercury pore volume, is a secondary predictor of certain rubber physical properties. The confidence limits of the predictions is dependent upon the concentration of precipitated silica used in the carbon black-filled rubber compound.

Effect of palmyra palm fiber filler on properties of natural rubber vulcanizate

2014 ◽  
Vol 11 (6) ◽  
pp. 565-574
Author(s):  
J. Nwabanne ◽  
P. Igbokwe ◽  
E. Ezeonyebuchi
Keyword(s):  
Particle Size ◽  
Carbon Black ◽  
Natural Rubber ◽  
Surface Area ◽  
Filler Loading ◽  
Partial Replacement ◽  
Average Particle ◽  
Swelling Properties ◽  
Palm Fiber ◽  
Loading Ratio

The effect of partial replacement of carbon black by Palmyra palm fiber on the cure characteristics, physico-mechanical and swelling properties of natural rubber vulcanizates was studied. The Palmyra palm fibers were extracted, treated and characterized so as to determine pH, moisture content, and ash content, loss on ignition, conductivity, cellulose, lignin, Hemicellulose, cellulose/lignin ratio and Acid soluble lignin. The functional groups in the Palmyra palm fiber was also determined using FTIR. The Palmyra palm powder with an average particle size of 75 μm was used in this study. The natural rubber/carbon black/Palmyra palm fiber (NR/CB/PPF) composites having eight different loadings, 0/70, 10/60, 20/50, 30/40, 40/30, 50/20, 60/10, 70/0, were prepared using a laboratory size two roll mill. The maximum Torque of NR/CB/PPF composites increased with increasing commercial filler loading ratio. The scorch time and cure time of NR/CB/PPF composites decreased as the ratio of CB loading increased. The tensile strength, modulus of elongation, tear strength and abrasion resistance of all the composites increased as the commercial filler loading ratio increased. This is due to the presence of the commercial filler which gave a better filler interaction. Also this behavior can be attributed to the particle size and surface area of the fillers used as the fillers with small particle size usually have a larger surface area which supports better filler-rubber interaction. The hardness increased as the palmyra palm fiber loading increased. The elongation at break decreases as carbon black filler loading increases except for the composite with CB/PPF ratio of 10/60. The effect of filler loading on the swelling behavior of NR/CB/PPF composites was also investigated in aromatic and aliphatic compounds. Result showed that the composites with more carbon black has less absorption than those with more palmyra palm fiber showing that the compounds with more carbon black has better interaction than those with palmyra palm fiber.

Sign in / Sign up

Export Citation Format

Share Document