scholarly journals Reactive sintering of B4c-TiB2 composites from B4 and TiO2 precursors

2020 ◽  
Vol 14 (4) ◽  
pp. 329-335
Author(s):  
Pavol Svec ◽  
Zuzana Gábrisová ◽  
Alena Brusilová
Keyword(s):  
Fracture Toughness ◽  
Boron Carbide ◽  
Titanium Diboride ◽  
Sintering Temperature ◽  
Secondary Phase ◽  
Ceramic Composites ◽  
Reactive Sintering ◽  
Different Temperatures ◽  
Carbide Matrix

The effect of sintering temperature in the interval from 1775 to 1850?C on the density, microstructure, hardness and fracture toughness of ceramic composites consisting of a boron carbide matrix and titanium diboride secondary phase was studied. The composites were hot pressed using in situ reaction between boron carbide and 40 wt.% of titanium dioxide additive. The samples were hot pressed at different temperatures but for the constant time of 60min, under the pressure of 35MPa in vacuum of 10 Pa. Both Vickers hardness and fracture toughness of the composites increased with the sintering temperature.Maximal hardness of 29.8GPa and fracture toughness of 6.9MPa?m1/2 were achieved for the composite with 29.6 vol.% of titanium diboride secondary phase sintered at the highest sintering temperature of 1850?C.

Pressureless Sintering and Properties of Boron Carbide-Titanium Diboride Composites by In Situ Reaction

2012 ◽  
Vol 525-526 ◽  
pp. 321-324 ◽  
Author(s):  
Ai Dong Liu ◽  
Ying Jie Qiao ◽  
Ying Ying Liu
Keyword(s):  
Flexural Strength ◽  
Boron Carbide ◽  
Titanium Diboride ◽  
Sintering Temperature ◽  
High Density ◽  
Sintering Behavior ◽  
Pressureless Sintering ◽  
In Situ Reaction

Pressureless sintering to obtain high density boron carbide-titanium diboride composites by in-situ reaction was studied. Pressureless sintering behavior of this material was investigated between 1800-2150 .The effects of composition, sintering temperature and tine were examined. Density up to 98.5% T.D. was reached at 2150. Maximum values of flexural strength (502 MPa), hardness (33 Gpa) and fracture toughnes (4.6 MPa·m1/2) were observed in the specimens containing 15 vol.% TiB2.

Optimization on Influencing Factors of Fracture Toughness of Corundum-Mullite Toughened by In Situ Synthesized Mullite Whiskers by Response Surface Methodology

2012 ◽  
Vol 581-582 ◽  
pp. 819-822 ◽  
Author(s):  
Bin Meng ◽  
Jin Hui Peng
Keyword(s):  
Fracture Toughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Response Surface Method ◽  
Sintering Temperature ◽  
Surface Method ◽  
Mullite Whiskers ◽  
Optimized Conditions ◽  
Addition Amount

The corundum-mullite was toughened by in-situ synthesized mullite whiskers and the process parameters influencing the fracture toughness of corundum-mullite, such as sintering temperature, addition amount of AlF3 and V2O5, were optimized by means of response surface method. Corundum-mullite with fracture toughness of 9.44 MPa.m-1/2 could be obtained under the optimized conditions, i.e. sintering temperature of 1400°C, 4.8 wt.% of AlF3 and 5.8 wt.% of V2O5. The results showed that it was feasible to prepare corundum-mullite toughened by in-situ synthesized mullite whiskers by the optimized parameters. In addition, an accurate model based on response surface method was proposed to predict the experimental results.

Effect of Sintering Temperature on Microstructure and Mechanical Properties of Al2O3-TiC-ZrO2 Ceramic Composites

2012 ◽  
Vol 476-478 ◽  
pp. 1031-1035
Author(s):  
Wei Min Liu ◽  
Xing Ai ◽  
Jun Zhao ◽  
Yong Hui Zhou
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Relative Density ◽  
Sintering Temperature ◽  
Ceramic Composites ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

Al2O3-TiC-ZrO2ceramic composites (ATZ) were fabricated by hot-pressed sintering. The phases and microstructure of the composites were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The relative density and mechanical properties (flexural strength, fracture toughness and Vicker’s hardness) of the composites were tested. The results show that the microstructure of the composites was the gray core-white rim. With the increase of sintering temperature, the relative density and mechanical properties of the composites increased first and then decreased. The composite sintered at 1705°C has the highest synthetical properties, and its relative density, flexural strength, fracture toughness and Vickers hardness are 98.3%,970MPa,6.0 MPa•m1/2and 20.5GPa, respectively.

Oxidation Behaviors of TiB2-TiCX and TiB2-TiCX/15SiC Ceramics

2010 ◽  
Vol 105-106 ◽  
pp. 179-183 ◽  
Author(s):  
De Gui Zhu ◽  
Hong Liang Sun ◽  
Yu Shu Wang ◽  
Liang Hui Wang
Keyword(s):  
Oxidation Resistance ◽  
Effective Temperature ◽  
Hot Isostatic Pressing ◽  
Ceramic Composites ◽  
Optical Micrograph ◽  
Different Temperatures ◽  
The Mean ◽  
Mean Time ◽  
Oxidation Behaviors

Fully dense samples of TiB2-TiCX and TiB2-TiCX/15SiC ceramic composites were fabricated by in-situ synthesis under hot isostatic pressing from TiH2, B4C and SiC powders. Their oxidized behaviors at different temperatures were tested. Optical micrograph studies and thermo-gravimetric analyses show that the highest effective temperature of oxidation resistance is 700°C for TiB2-TiCX, and 1100°C for TiB2-TiCX/15SiC. The weight gain of TiB2-TiCX/15SiC below 1100°C is quite low, and it rises up suddenly when the temperature reaches 1200°C. Thus, the highest effective temperature of oxidation resistance is 1100°C for TiB2-TiCX/15SiC. The oxidation dynamic curves of TiB2-TiCX/15SiC ceramics accord with the parabola’s law. The activation energy of TiB2-TiCx/15SiC (189.87kJ.mol-1) is higher than that of TiB2-TiCx (96.44kJ.mol-1). In the oxidation process of TiB2-TiCx/15SiC, TiB2 reacts with oxygen and generates TiO2 and B2O3 at first. A layer of whole homogeneous oxide film cannot be formed, in the mean time, the oxidation of TiC begins. When temperature goes up to 1000°C, TiC phase is totally oxidized. SiC is oxidized to SiO2 at about 900°C, Meanwhile, TiO2 forms denser film than B2O3, which grows and covers the surface of the material, and gives better property of oxidation resistance.

Pressureless Sintering of Boron Carbide-Based Superhard Materials

2010 ◽  
Vol 159 ◽  
pp. 145-148 ◽  
Author(s):  
Dimitar D. Radev
Keyword(s):  
Transition Metal ◽  
Boron Carbide ◽  
Sintering Temperature ◽  
Liquid Phase Sintering ◽  
Vacuum Furnace ◽  
Pressureless Sintering ◽  
Metal Carbides ◽  
Sintering Aids ◽  
Transition Metal Carbides

Boron carbide-based materials B4C-MexBy were densified by pressureless sintering in a vacuum furnace. Some transition metal carbides (TiC, ZrC, HfC, Cr3C2 and WC) from groups IV-VI were used as sintering aids. The optimal sintering temperature in the range 2220-2250oC was used for any composition. Here we show the possibilities to activate the mass transport of the B4C by the mechanism of liquid phase sintering. The method of reactive sintering of B4C in the presence of additives of some transition metal carbides allows in situ synthesis of dense B4C-MexBy materials. Structural properties and fracture toughness of the B4C-based composite materials were discussed. The properties of some of these materials and the possibilities for their application are also discussed.

Self-Toughness Porous Sodium Titanate Bioceramics Prepared via In Situ Grown Na2Ti6O13 Rods

2017 ◽  
Vol 727 ◽  
pp. 806-814 ◽  
Author(s):  
Xiao Wei Ma ◽  
Jian Xing Shen ◽  
Ke Chang Zhang ◽  
Ling Kai Kong ◽  
Jia Le Sun ◽  
...  
Keyword(s):  
Fracture Toughness ◽  
Compressive Strength ◽  
Sodium Titanate ◽  
The Novel ◽  
Ceramic Samples ◽  
Porous Bioceramic ◽  
Different Temperatures ◽  
Growth Method ◽  
Titanate Ceramics

Here in, we report the porous bioceramic with Na2Ti6O13 rods prepared by in‒situ growth method. The samples were prepared using cold uniaxial pressing (40 MPa) technique and further sintered at different temperatures. The structure and morphology were characterized by XRD and SEM. The porosity, compressive strength and fracture toughness were also investigated. The bone-like apatite deposition ability of the fabricated ceramic samples was evaluated by Kokubo simulated body fluid (SBF) soaking method. The results indicated that the Na2Ti6O13 rods with about 1‒3 μm in diameter are uniformly distributed in the self‒toughness porous sodium titanate ceramics (SPSTC). The SPSTC with a porosity of 61.10±1.12 % exhibits good compressive strength (43.36±2.43 MPa) and fracture toughness (3.47±0.21 MPa·m1/2). The results indicate that the novel SPSTC scaffolds are promising for bone tissue engineering applications.

scholarly journals Effect of Sintering Temperature on Metal-Insulator Phase Transition in La1-xCaxMnO3 Perovskites

2020 ◽  
Vol 2 (1) ◽  
pp. 37-42
Author(s):  
Arunachalam M ◽  
Thamilmaran P ◽  
Sakthipandi K
Keyword(s):  
Phase Transition ◽  
Bulk Modulus ◽  
Sintering Temperature ◽  
Magnetic Sensors ◽  
Temperature Dependent ◽  
Metal Insulator ◽  
Wide Range ◽  
Different Temperatures ◽  
Insulator Phase Transition

Lanthanum calcium based perovskites are found to be advantageous for the possible applications in magnetic sensors/reading heads, cathodes in solid oxide fuel cells, and frequency switching devices. In the present investigation La0.3Ca0.7MnO3 perovskites were synthesised through solid state reaction and sintered at four different temperatures such as 900, 1000, 1100 and 1200˚ C. X-ray powder diffraction pattern confirms that the prepared La0.3Ca0.7MnO3 perovskites have orthorhombic structure with Pnma space group. Ultrasonic in-situ measurements have been carried out on the La0.3Ca0.7MnO3 perovskites over wide range of temperature and elastic constants such as bulk modulus of the prepared La0.3Ca0.7MnO3 perovskites was obtained as function of temperature. The temperature-dependent bulk modulus has shown an interesting anomaly at the metal-insulator phase transition. The metal insulator transition temperature derived from temperature-dependent bulk modulus increases from temperature 352˚ C to 367˚ C with the increase of sintering temperature from 900 to 1200˚ C.

Microstructure Formation and Performance of Reactive Sintered Titanium Oxycarbide Base Ceramic-Ceramic Composites

2019 ◽  
Vol 799 ◽  
pp. 131-135
Author(s):  
Kristjan Juhani ◽  
Jakob Kübarsepp ◽  
Marek Tarraste ◽  
Jüri Pirso ◽  
Mart Viljus
Keyword(s):  
Phase Formation ◽  
Mechanical Performance ◽  
Aluminium Oxide ◽  
High Energy ◽  
Ceramic Composites ◽  
Oxide Ceramic ◽  
Reactive Sintering ◽  
Attritor Milling ◽  
Different Temperatures ◽  
And Performance

Reactive sintering is a process where synthesis reaction of the ceramic phases is combined with sintering (densification) of the composite. Dense lightweight titanium oxycarbide-aluminium oxide ceramic-ceramic composites were produced from titanium dioxide, carbon black as graphite source and aluminium precursors by high energy attritor milling, followed by reactive sintering. Titanium oxycarbide and aluminium oxide phases were synthesized during reactive sintering in situ. To investigate the microstructure evolution and phase formation, the specimens were sintered at different temperatures (600-1725 °C) in vacuum. Scanning electron microscopy and X-ray diffraction were used to analyze the microstructure and phase formation. Mechanical performance (hardness and fracture toughness) was evaluated.

Effect of Y2O3 on the Sintering, Mechanical and Dielectric Properties of Mullite/h-BN Composites

2016 ◽  
Vol 848 ◽  
pp. 28-31
Author(s):  
Han Jin ◽  
Yong Feng Li ◽  
Zhong Qi Shi ◽  
Hong Yan Xia ◽  
Guan Jun Qiao
Keyword(s):  
Fracture Toughness ◽  
Dielectric Constant ◽  
Phase Composition ◽  
High Temperature ◽  
Dielectric Properties ◽  
Liquid Phase ◽  
Flexural Strength ◽  
Sintering Temperature ◽  
Pressureless Sintering ◽  
Different Temperatures

Mullite/10 wt. %h-BN composites with 5 wt. % Y2O3 additive were fabricated by pressureless sintering at different temperatures. The densification, phase composition, microstructure, mechanical and dielectric properties of the mullite/h-BN composites were investigated. With the addition of Y2O3, the sintering temperature of the mullite/h-BN composites declined, while the density, mechanical and dielectric properties all increased. The addition of Y2O3 promoted the formation of liquid phase at high temperature, which accelerated the densification. Besides, Y2O3 particles which were located at the grain boundaries inhibited the grain growth of mullite matrix. For the mullite/h-BN composites with Y2O3 additive, the appropriate sintering temperature was about 1600°C. The relative density, flexural strength, fracture toughness and dielectric constant of the Y2O3 doped mullite/h-BN composite sintered at 1600 °C reached 82%, 135 MPa, 2.3 MPa·m1/2 and 4.9, respectively.

Microstructure and Mechanical Properties of TiC/Ti3AlC2 In Situ Composites Prepared by Hot Pressing Method

2015 ◽  
Vol 816 ◽  
pp. 200-204 ◽  
Author(s):  
Miao Miao Ruan ◽  
Xiao Ming Feng ◽  
Tao Tao Ai ◽  
Ning Yu ◽  
Kui Hua
Keyword(s):  
Fracture Toughness ◽  
Flexural Strength ◽  
Vickers Hardness ◽  
Hot Pressing ◽  
Sintering Temperature ◽  
Powder Mixtures ◽  
Pressing Method ◽  
Hot Pressing Sintering ◽  
Sintering Method

TiC/Ti3AlC2 composites were successfully prepared by hot-pressing sintering method from the elemental powder mixtures of Ti, Al and TiC. A possible reaction mechanism was investigated by XRD. The density, Vickers hardness, flexural strength, and fracture toughness of the TiC/Ti3AlC2 composites were also measured. At 660 °C, Al melted and reacted with Ti to form TiAl3. At 900 °C, TiAl3 reacted with TiC and Ti to form Ti2AlC. At 1100 °C, Ti2AlC reacted with TiC to form Ti3AlC2. Increasing the sintering temperature, the content of Ti3AlC2 increased. The TiC/Ti3AlC2 composites had excellent performance after sintered at 1100 °C, the density, Vickers hardness, flexural strength and fracture toughness of the composite were 4.35 g/cm3, 4.72 GPa, 566 MPa and 6.18 MPa·m1/2, respectively.

Sign in / Sign up

Export Citation Format

Share Document