scholarly journals The effects of fine grinding on the physicochemical properties and thermal behavior of bentonite clay

2002 ◽  
Vol 67 (11) ◽  
pp. 753-760 ◽  
Author(s):  
Leposava Filipovic-Petrovic ◽  
Ljiljana Kostic-Gvozdenovic ◽  
Stanka Eric-Antonic
Keyword(s):  
Mechanical Treatment ◽  
Structural Changes ◽  
Bentonite Clay ◽  
Powdered Material ◽  
X Ray Diffraction ◽  
X Ray ◽  
Fine Grinding ◽  
Dta Analysis ◽  
Processing Steps ◽  
Vibration Mill

In this study, the results obtained by the mechanical treatment of bentonite clay Zavidinci, Serbia in a laboratory vibration mill with rings for different periods of time are presented. The successive structural changes of the minerals were studied by X-ray diffraction analysis, DTA analysis, IR spectroscopy and particle size distribution. The reactivity changes were controlled by CEC. The starting material and the material mechanically treated for 30 min were sintered at several temperature and for different time periods examined by X-ray diffraction. Mechanical treatment by fine grinding of bentonite clay produces structural changes of the powdered material and influences its behavior in further processing steps in particular after thermal treatment.

scholarly journals High temperature structural study of decagonal Al-Cu-Rh quasicrystal.

2014 ◽  
Vol 70 (a1) ◽  
pp. C94-C94
Author(s):  
Pawel Kuczera ◽  
Walter Steurer
Keyword(s):  
Structural Changes ◽  
Configurational Entropy ◽  
Lattice Vibrations ◽  
X Ray Diffraction ◽  
Stabilization Mechanism ◽  
X Ray ◽  
Comparative Structure ◽  
The Stability

The structure of d(ecagonal)-Al-Cu-Rh has been studied as a function of temperature by in-situ single-crystal X-ray diffraction in order to contribute to the discussion on energy or entropy stabilization of quasicrystals (QC) [1]. The experiments were performed at 293 K, 1223 K, 1153 K, 1083 K, and 1013 K. A common subset of 1460 unique reflections was used for the comparative structure refinements at each temperature. The results obtained for the HT structure refinements of d-Al-Cu-Rh QC seem to contradict a pure phasonic-entropy-based stabilization mechanism [2] for this QC. The trends observed for the ln func(I(T1 )/I(T2 )) vs.|k⊥ |^2 plots indicate that the best on-average quasiperiodic order exists between 1083 K and 1153 K, however, what that actually means is unclear. It could indicate towards a small phasonic contribution to entropy, but such contribution is not seen in the structure refinements. A rough estimation of the hypothetic phason instability temperature shows that it would be kinetically inaccessible and thus the phase transition to a 12 Å low T structure (at ~800 K) is most likely not phason-driven. Except for the obvious increase in the amplitude of the thermal motion, no other significant structural changes, in particular no sources of additional phason-related configurational entropy, were found. All structures are refined to very similar R-values, which proves that the quality of the refinement at each temperature is the same. This suggests, that concerning the stability factors, some QCs could be similar to other HT complex intermetallic phases. The experimental results clearly show that at least the ~4 Å structure of d-Al-Cu-Rh is a HT phase therefore entropy plays an important role in its stabilisation mechanism lowering the free energy. However, the main source of this entropy is probably not related to phason flips, but rather to lattice vibrations, occupational disorder unrelated to phason flips like split positions along the periodic axis.

Investigations of Actinide Metals and Compounds under Pressure Provide Important Insights into Bonding and Chemistry

2003 ◽  
Vol 802 ◽  
Author(s):  
R. G. Haire ◽  
S. Heathman ◽  
T. Le Bihan ◽  
A. Lindbaum ◽  
M. Iridi
Keyword(s):  
Structural Changes ◽  
Chemical Properties ◽  
X Ray Diffraction ◽  
Interatomic Distances ◽  
X Ray ◽  
Effect Of Pressure ◽  
Electronic Configurations ◽  
5F Electrons ◽  
Actinide Series ◽  
Alloys And Compounds

ABSTRACTOne effect of pressure on elements and compounds is to decease their interatomic distances, which can bring about dramatic perturbations in their electronic nature and bonding, which can be reflected in changes in physical and/or chemical properties. One important issue in the actinide series of elements is the effect of pressure on the 5f-electrons. We have probed changes in electronic behavior with pressure by monitoring structure by X-ray diffraction, and have studied several actinide metals and compounds from thorium through einsteinium. These studies have employed angle dispersive diffraction using synchrotron radiation, and energy dispersive techniques via conventional X-ray sources. The 5f-electrons of actinide metals and their alloys are often affected significantly by pressure, while with compounds, the structural changes are often not linked to the involvement of 5 f-electron. We shall present some of our more recent findings from studies of selected actinide metals, alloys and compounds under pressure. A discussion of the results in terms of the changes in electronic configurations and bonding with regard to the element's position in the series is also addressed.

Development of WC-Fe3Al Composites by Spark Plasma Sintering Process

2016 ◽  
Vol 881 ◽  
pp. 307-312
Author(s):  
Luis Antonio C. Ybarra ◽  
Afonso Chimanski ◽  
Sergio Gama ◽  
Ricardo A.G. da Silva ◽  
Izabel Fernanda Machado ◽  
...  
Keyword(s):  
Spark Plasma Sintering ◽  
Zinc Stearate ◽  
Sintering Process ◽  
X Ray Diffraction ◽  
X Ray ◽  
Plasma Sintering ◽  
Al Composite ◽  
Spark Plasma ◽  
Short Time ◽  
Vibration Mill

Tungsten carbide (WC) based composites are usually produced with cobalt, but this binder has the inconvenience of shortage, unstable price and potential carcinogenicity. The objective of this study was to develop WC composite with intermetallic Fe3Al matrix. Powders of WC, iron and aluminum, with composition WC-10 wt% Fe3Al, and 0.5 wt% zinc stearate were milled in a vibration mill for 6 h and sintered in a SPS (spark plasma sintering) furnace at 1150 °C for 8 min under pressure of 30 MPa. Measured density and microstructure analysis showed that the composite had significant densification during the (low-temperature, short time) sintering, and X-ray diffraction analysis showed the formation of intermetallic Fe3Al. Analysis by Vickers indentation resulted in hardness of 11.2 GPa and fracture toughness of 24.6 MPa.m1/2, showing the feasibility of producing dense WC-Fe3Al composite with high mechanical properties using the SPS technique.

Structural changes in titanium dioxide nanocrystals during plastic deformation

2005 ◽  
Vol 38 (5) ◽  
pp. 749-756 ◽  
Author(s):  
Ulrich Gesenhues
Keyword(s):  
Structural Changes ◽  
Crystal Size ◽  
Lower Layer ◽  
High Energy ◽  
Primary Crystal ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Hall Method ◽  
Means Of Transmission

The polygonization of 200 nm rutile crystals during dry ball-milling at 10gwas monitored in detail by means of transmission electron microscopy (TEM) and X-ray diffraction (XRD). The TEM results showed how to modify the Williamson–Hall method for a successful evaluation of crystal size and microstrain from XRD profiles. Macrostrain development was determined from the minute shift of the most intense reflection. In addition, changes in pycnometrical density were monitored. Accordingly, the primary crystal is disintegrated during milling into a mosaic of 12–35 nm pieces where the grain boundaries induce up to 1.2% microstrain in a lower layer of 6 nm thickness. Macrostrain in the interior of the crystals rises to 0.03%. The pycnometrical density, reflecting the packing density of atoms in the grain boundary, decreases steadily by 1.1%. The results bear relevance to our understanding of plastic flow and the mechanism of phase transitions of metal oxides during high-energy milling.

scholarly journals Structural Evolution in Wet Mechanically Alloyed Co-Fe-(Ta,W)-B Alloys

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 800
Author(s):  
Vladimír Girman ◽  
Maksym Lisnichuk ◽  
Daria Yudina ◽  
Miloš Matvija ◽  
Pavol Sovák ◽  
...  
Keyword(s):  
Structural Changes ◽  
Magnetic Measurements ◽  
Structural Evolution ◽  
High Energy ◽  
Control Agent ◽  
X Ray Diffraction ◽  
Mechanically Alloyed ◽  
X Ray ◽  
Transmission Electron ◽  
X Ray Absorption

In the present study, the effect of wet mechanical alloying (MA) on the glass-forming ability (GFA) of Co43Fe20X5.5B31.5 (X = Ta, W) alloys was studied. The structural evolution during MA was investigated using high-energy X-ray diffraction, X-ray absorption spectroscopy, high-resolution transmission electron microscopy and magnetic measurements. Pair distribution function and extended X-ray absorption fine structure spectroscopy were used to characterize local atomic structure at various stages of MA. Besides structural changes, the magnetic properties of both compositions were investigated employing a vibrating sample magnetometer and thermomagnetic measurements. It was shown that using hexane as a process control agent during wet MA resulted in the formation of fully amorphous Co-Fe-Ta-B powder material at a shorter milling time (100 h) as compared to dry MA. It has also been shown that substituting Ta with W effectively suppresses GFA. After 100 h of MA of Co-Fe-W-B mixture, a nanocomposite material consisting of amorphous and nanocrystalline bcc-W phase was synthesized.

scholarly journals Investigation and Modeling of the Electrical Conductivity of Graphene Nanoplatelets-Loaded Doped-Polypyrrole

Polymers ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1034
Author(s):  
Oladipo Folorunso ◽  
Yskandar Hamam ◽  
Rotimi Sadiku ◽  
Suprakas Sinha Ray ◽  
Neeraj Kumar
Keyword(s):  
Electrical Conductivity ◽  
Structural Changes ◽  
Spherical Shape ◽  
Graphene Nanoplatelets ◽  
Conductivity Measurements ◽  
X Ray Diffraction ◽  
X Ray ◽  
Thermogravimetric Analyzer ◽  
Energy Storage Applications ◽  
Electrical Conductivity Data

In this study, a hybrid of graphene nanoplatelets with a polypyrrole having 20 wt.% loading of carbon-black (HGPPy.CB20%), has been fabricated. The thermal stability, structural changes, morphology, and the electrical conductivity of the hybrids were investigated using thermogravimetric analyzer, differential scanning calorimeter, X-ray diffraction analyzer, scanning electron microscope, and laboratory electrical conductivity device. The morphology of the hybrid shows well dispersion of graphene nanoplatelets on the surface of the PPy.CB20% and the transformation of the gravel-like PPy.CB20% shape to compact spherical shape. Moreover, the hybrid’s electrical conductivity measurements showed percolation threshold at 0.15 wt.% of the graphene nanoplatelets content and the curve is non-linear. The electrical conductivity data were analyzed by comparing different existing models (Weber, Clingerman and Taherian). The results show that Taherian and Clingerman models, which consider the aspect ratio, roundness, wettability, filler electrical conductivity, surface interaction, and volume fractions, closely described the experimental data. From these results, it is evident that Taherian and Clingerman models can be modified for better prediction of the hybrids electrical conductivity measurements. In addition, this study shows that graphene nanoplatelets are essential and have a significant influence on the modification of PPy.CB20% for energy storage applications.

Size dependent behavior of Fe3O4crystals during electrochemical (de)lithiation: an in situ X-ray diffraction, ex situ X-ray absorption spectroscopy, transmission electron microscopy and theoretical investigation

2017 ◽  
Vol 19 (31) ◽  
pp. 20867-20880 ◽  
Author(s):  
David C. Bock ◽  
Christopher J. Pelliccione ◽  
Wei Zhang ◽  
Janis Timoshenko ◽  
K. W. Knehr ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Structural Changes ◽  
Ex Situ ◽  
X Ray Diffraction ◽  
X Ray ◽  
Size Dependent ◽  
Transmission Electron ◽  
Dependent Behavior ◽  
X Ray Absorption

Crystal and atomic structural changes of Fe3O4upon electrochemical (de)lithiation were determined.

Influence of Organophilization Process Variables in Bentonite Clays from Cubati-PB

2012 ◽  
Vol 727-728 ◽  
pp. 1467-1472
Author(s):  
Carla Dantas da Silva ◽  
Rosa do Carmo de Oliveira Lima ◽  
Julliana Marques Rocha Costa ◽  
Gelmires Araújo Neves ◽  
Heber Carlos Ferreira
Keyword(s):  
Thermogravimetric Analysis ◽  
Bentonite Clay ◽  
Laser Diffraction ◽  
Ionic Surfactants ◽  
Organic Media ◽  
Process Variables ◽  
X Ray Diffraction ◽  
X Ray ◽  
Bentonite Clays ◽  
Sodium Form

This work aims at the development of organoclay from two varieties of bentonite for use in organic media using ionic surfactants, studying the influence of process variables in the organophilization process. We used the following materials: natural bentonite clay from Cubati-PB District, and the ionic quaternary ammonium salt: Praepagen WB® with 45% active matter. The clays were benefited and then turned into sodium form and subsequently into organoclays. The bentonites were characterized by laser diffraction (GA) X-ray fluorescence chemical composition (EDX), thermogravimetric analysis (TGA), thermogravimetry (DTA) and X-ray diffraction (XRD). The organoclays were characterized by (XRD) thermogravimetric analysis (TGA) and thermogravimetry (DTA). The results showed that the clay has potential for application in the organophilization process and that there is influence of process variables.

X-ray diffraction investigations of structural changes in Co/Cu multilayers at elevated temperatures

2002 ◽  
Vol 411 (2) ◽  
pp. 234-239 ◽  
Author(s):  
M Hecker ◽  
W Pitschke ◽  
D Tietjen ◽  
C.M Schneider
Keyword(s):  
Structural Changes ◽  
Elevated Temperatures ◽  
X Ray Diffraction ◽  
X Ray
Sign in / Sign up

Export Citation Format

Share Document