scholarly journals Effect of solid fraction on the mechanical properties of thixomolded magnesium alloys

2008 ◽  
Vol 44 (1) ◽  
pp. 101-106 ◽  
Author(s):  
V. Goryany ◽  
P.J. Mauk
Keyword(s):  
Mechanical Properties ◽  
Magnesium Alloys ◽  
Solid Fraction ◽  
Solid Phase ◽  
Flow Characteristics ◽  
Temperature Profiles ◽  
Pouring Temperature ◽  
Solid Matter

The higher the fraction of solid phase in the partly solidified melt during pouring, the poorer the mechanical properties of thixocast components. The solid fraction decreases as the pouring temperature rises. Recommended temperature profiles for the pouring cylinder are shown. The flow characteristics of the partly solidified melt hardly changes as the content of solid matter increases.

Influence of the Pouring Temperature on the Castability and Microstructure of Elektron 21 and QE22 Magnesium Casting Alloys

2013 ◽  
Vol 197 ◽  
pp. 125-130
Author(s):  
Bartłomiej Dybowski ◽  
Robert Jarosz ◽  
Andrzej Kiełbus
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Magnesium Alloys ◽  
Automotive Industry ◽  
Volume Fraction ◽  
Low Density ◽  
Pouring Temperature ◽  
Casting Alloys ◽  
Magnesium Casting

Magnesium alloys are widely used in aerospace and automotive industry due to their low density, good mechanical properties and good castability. The paper presents results of the castability tests and microstructural investigations on two unmodified magnesium casting alloys, Elektron 21 and QE22. Spirals for the castability test were poured from three temperatures: 755°C, 800°C and 835°C. Volume fraction of eutectic regions and grain size in both alloys were quantitatively evaluated. Castability increased with increasing pouring temperature. Quantity of eutectics and grain size did not show straight correlation with pouring temperature.

Influence of Pouring Temperature on Castability and Microstructure of QE22 and RZ5 Magnesium Casting Alloys

2012 ◽  
Vol 191 ◽  
pp. 137-144 ◽  
Author(s):  
Bartlomiej Dybowski ◽  
Robert Jarosz ◽  
Andrzej Kiełbus ◽  
Jan Cwajna
Keyword(s):  
Mechanical Properties ◽  
Corrosion Resistance ◽  
Rare Earth ◽  
High Temperature ◽  
Magnesium Alloys ◽  
Volume Fraction ◽  
Low Density ◽  
Pouring Temperature ◽  
Casting Alloys ◽  
Magnesium Casting

Magnesium alloys are widely used in automotive and aerospace industries due to their great connection of low density and good mechanical properties. They are also characterized by good castability and weldability. Their weak high temperature properties and corrosion resistance, led to development of magnesium alloys containing rare earth elements. Casting is the most popular way of manufacturing magnesium elements. However, there is a lack of investigations concerning impact of different factors on fluidity of these alloys. This paper presents results of investigations on influence of pouring temperature on castability and microstructure of QE22 and RZ5 magnesium alloys. In case of QE22 alloy, the filling length of the liquid alloy increased with the increasing pouring temperature. In RZ5 no such dependence was noted. This is probably caused by oxide films in the structure of material. Grain refinement and eutectics volume fraction also didn’t present correlation with pouring temperature.

Effects of Vickers Cracks on the Mechanical Properties of Solid-phase-sintered Silicon Carbide Ceramics

2012 ◽  
Vol 27 (9) ◽  
pp. 965-969
Author(s):  
Xiao YANG ◽  
Xue-Jian LIU ◽  
Zheng-Ren HUANG ◽  
Gui-Ling LIU ◽  
Xiu-Min YAO
Keyword(s):  
Mechanical Properties ◽  
Silicon Carbide ◽  
Solid Phase ◽  
Carbide Ceramics ◽  
Silicon Carbide Ceramics ◽  
Sintered Silicon

Enhanced mechanical properties of as-cast Mg-Al-Ca magnesium alloys by friction stir processing

2021 ◽  
Vol 296 ◽  
pp. 129880
Author(s):  
Zahra Nasiri ◽  
Mahmoud Sarkari Khorrami ◽  
Hamed Mirzadeh ◽  
Massoud Emamy
Keyword(s):  
Mechanical Properties ◽  
Magnesium Alloys ◽  
Friction Stir Processing ◽  
Friction Stir

The influence of gadolinium on Al–Ti–C master alloy and its refining effect on AZ31 magnesium alloy

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Wenxue Fan ◽  
Hai Hao
Keyword(s):  
Mechanical Properties ◽  
Magnesium Alloy ◽  
Grain Refinement ◽  
Magnesium Alloys ◽  
Master Alloy ◽  
Cast Alloy ◽  
Az31 Magnesium Alloy ◽  
Synthesis Mechanism ◽  
Refining Effect ◽  
Master Alloys

Abstract Grain refinement has a significant influence on the improvement of mechanical properties of magnesium alloys. In this study, a series of Al–Ti–C-xGd (x = 0, 1, 2, 3) master alloys as grain refiners were prepared by self-propagating high-temperature synthesis. The synthesis mechanism of the Al–Ti–C-xGd master alloy was analyzed. The effects of Al–Ti–C-xGd master alloys on the grain refinement and mechanical properties of AZ31 (Mg-3Al-1Zn-0.4Mn) magnesium alloys were investigated. The results show that the microstructure of the Al–Ti–C-xGd alloy contains α-Al, TiAl3, TiC and the core–shell structure TiAl3/Ti2Al20Gd. The refining effect of the prepared Al–Ti–C–Gd master alloy is obviously better than that of Al–Ti–C master alloy. The grain size of AZ31 magnesium alloy was reduced from 323 μm to 72 μm when adding 1 wt.% Al–Ti–C-2Gd master alloy. In the same condition, the ultimate tensile strength and elongation of as-cast alloy were increased from 130 MPa, 7.9% to 207 MPa, 16.6% respectively.

scholarly journals Comprehensive Analysis of the Microstructure and Mechanical Properties of Friction-Stir-Welded Low-Carbon High-Strength Steels with Tensile Strengths Ranging from 590 MPa to 1.5 GPa

2021 ◽  
Vol 11 (12) ◽  
pp. 5728
Author(s):  
HyeonJeong You ◽  
Minjung Kang ◽  
Sung Yi ◽  
Soongkeun Hyun ◽  
Cheolhee Kim
Keyword(s):  
Mechanical Properties ◽  
Tensile Test ◽  
Joint Strength ◽  
Solid Phase ◽  
Welding Process ◽  
High Strength Steels ◽  
High Strength ◽  
Low Carbon ◽  
Friction Stir ◽  
Welding Processes

High-strength steels are being increasingly employed in the automotive industry, requiring efficient welding processes. This study analyzed the materials and mechanical properties of high-strength automotive steels with strengths ranging from 590 MPa to 1500 MPa, subjected to friction stir welding (FSW), which is a solid-phase welding process. The high-strength steels were hardened by a high fraction of martensite, and the welds were composed of a recrystallized zone (RZ), a partially recrystallized zone (PRZ), a tempered zone (TZ), and an unaffected base metal (BM). The RZ exhibited a higher hardness than the BM and was fully martensitic when the BM strength was 980 MPa or higher. When the BM strength was 780 MPa or higher, the PRZ and TZ softened owing to tempered martensitic formation and were the fracture locations in the tensile test, whereas BM fracture occurred in the tensile test of the 590 MPa steel weld. The joint strength, determined by the hardness and width of the softened zone, increased and then saturated with an increase in the BM strength. From the results, we can conclude that the thermal history and size of the PRZ and TZ should be controlled to enhance the joint strength of automotive steels.

scholarly journals Cationic Copolymerization of Isobutylene with 4-Vinylbenzenecyclobutylene: Characteristics and Mechanisms

Polymers ◽  
2020 ◽  
Vol 12 (1) ◽  
pp. 201 ◽  
Author(s):  
Zhifei Chen ◽  
Shuxin Li ◽  
Yuwei Shang ◽  
Shan Huang ◽  
Kangda Wu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Molecular Weight ◽  
Cationic Polymerization ◽  
Transfer Reaction ◽  
Chain Transfer ◽  
Solid Phase ◽  
Random Copolymer ◽  
Glass Transition Temperatures ◽  
Cationic Copolymerization ◽  
Chain Transfer Reaction

A random copolymer of isobutylene (IB) and 4-vinylbenzenecyclobutylene (4-VBCB) was synthesized by cationic polymerization at −80 °C using 2-chloro-2,4,4-trimethylpentane (TMPCl) as initiator. The laws of copolymerization were investigated by changing the feed quantities of 4-VBCB. The molecular weight of the copolymer decreased, and its molecular weight distribution (MWD) increased with increasing 4-VBCB content. We proposed a possible copolymerization mechanism behind the increase in the chain transfer reaction to 4-VBCB with increasing of feed quantities of 4-VBCB. The thermal properties of the copolymers were studied by solid-phase heating and crosslinking. After crosslinking, the decomposition and glass transition temperatures (Tg) of the copolymer increased, the network structure that formed did not break when reheated, and the mechanical properties remarkably improved.

Effect of Pouring Temperature and Holding Time at Semi-Solid Region on the Morphology of Primary Solid Phase in Semi-Solid Slurry

2006 ◽  
Vol 510-511 ◽  
pp. 782-785 ◽  
Author(s):  
Suk Won Kang ◽  
Ki Bae Kim ◽  
Dock Young Lee ◽  
Jung-Hwa Mun ◽  
Eui Pak Yoon
Keyword(s):  
Solid Phase ◽  
Holding Time ◽  
Pouring Temperature ◽  
Solid Region ◽  
Semi Solid

On changes in mechanical properties of polyamic acid during solid phase chemical imidization

1985 ◽  
Vol 27 (4) ◽  
pp. 905-911 ◽  
Author(s):  
M.M. Koton ◽  
T.K. Meleshko ◽  
V.V. Kudryavtsev ◽  
I.V. Gofman ◽  
N.P. Kuznetsov ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Solid Phase ◽  
Polyamic Acid ◽  
Phase Chemical

Microstructure and Mechanical Properties of ZrB2/h-BN Multiphase Ceramics by Low-Temperature Reactive Sintering

2016 ◽  
Vol 697 ◽  
pp. 510-514 ◽  
Author(s):  
Feng Rui Zhai ◽  
Ke Shan ◽  
Ruo Meng Xu ◽  
Min Lu ◽  
Zhong Zhou Yi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Relative Density ◽  
Fracture Strength ◽  
Solid Phase ◽  
Raw Materials ◽  
Solid Phase Reaction ◽  
Phase Reaction ◽  
Microstructure And Mechanical Properties ◽  
Multiphase Ceramics ◽  
Strength And Toughness

In the present paper, the ZrB2/h-BN multiphase ceramics were fabricated by SPS (spark plasma sintering) technology at lower sintering temperature using h-BN, ZrO2, AlN and Si as raw materials and B2O3 as a sintering aid. The phase constitution and microstructure of specimens were analyzed by XRD and SEM. Moreover, the effects of different sintering pressures on the densification, microstructure and mechanical properties of ZrB2/h-BN multiphase ceramics were also systematically investigated. The results show that the ZrB2 was obtained through solid phase reaction at different sintering pressures, and increasing sintering pressure could accelerate the formation of ZrB2 phase. As the sintering pressure increasing, the fracture strength and toughness of the sintered samples had a similar increasing tendency as the relative density. The better comprehensive properties were obtained at given sintering pressure of 50MPa, and the relative density, fracture strength and toughness reached about 93.4%, 321MPa and 3.3MPa·m1/2, respectively. The SEM analysis shows that the h-BN grains were fine and uniform, and the effect of sintering pressure on grain size was inconspicuous. The distribution of grain is random cross array, and the fracture texture was more obvious with the increase of sintering pressure. The fracture mode of sintered samples remained intergranular fracture mechanism as sintering pressure changed, and the grain refinement, grain pullout and crack deflection helped to increase the mechanical properties.

Sign in / Sign up

Export Citation Format

Share Document