scholarly journals Comprehensive Analysis of the Microstructure and Mechanical Properties of Friction-Stir-Welded Low-Carbon High-Strength Steels with Tensile Strengths Ranging from 590 MPa to 1.5 GPa

2021 ◽  
Vol 11 (12) ◽  
pp. 5728
Author(s):  
HyeonJeong You ◽  
Minjung Kang ◽  
Sung Yi ◽  
Soongkeun Hyun ◽  
Cheolhee Kim
Keyword(s):  
Mechanical Properties ◽  
Tensile Test ◽  
Joint Strength ◽  
Solid Phase ◽  
Welding Process ◽  
High Strength Steels ◽  
High Strength ◽  
Low Carbon ◽  
Friction Stir ◽  
Welding Processes

High-strength steels are being increasingly employed in the automotive industry, requiring efficient welding processes. This study analyzed the materials and mechanical properties of high-strength automotive steels with strengths ranging from 590 MPa to 1500 MPa, subjected to friction stir welding (FSW), which is a solid-phase welding process. The high-strength steels were hardened by a high fraction of martensite, and the welds were composed of a recrystallized zone (RZ), a partially recrystallized zone (PRZ), a tempered zone (TZ), and an unaffected base metal (BM). The RZ exhibited a higher hardness than the BM and was fully martensitic when the BM strength was 980 MPa or higher. When the BM strength was 780 MPa or higher, the PRZ and TZ softened owing to tempered martensitic formation and were the fracture locations in the tensile test, whereas BM fracture occurred in the tensile test of the 590 MPa steel weld. The joint strength, determined by the hardness and width of the softened zone, increased and then saturated with an increase in the BM strength. From the results, we can conclude that the thermal history and size of the PRZ and TZ should be controlled to enhance the joint strength of automotive steels.

Cooling Curve Based Estimation of Mechanical Properties in High Strength Steel Welds

2016 ◽  
Vol 879 ◽  
pp. 1760-1765 ◽  
Author(s):  
Rahul Sharma ◽  
Uwe Reisgen
Keyword(s):  
Mechanical Properties ◽  
Welding Process ◽  
High Strength Steels ◽  
High Strength ◽  
Structural Steels ◽  
Cooling Time ◽  
Cooling Curve ◽  
Welding Parameters ◽  
Steel Welds ◽  
Welding Processes

The application of high strength steels in welded structures relies on easy to use quality assurance concepts for the welding process. For ferritic steels, one of the most common methods for estimating the mechanical properties of welded joints is the cooling time concept t8/5. Even without experimental determination, the calculation of cooling time with previously introduced formulas based on the welding parameters leads to good results. Because high strength structural steels and weld metals with a yield strength of 960 MPa contain higher quantities of alloying elements, the transformation start temperature Ar3 is found to be outside of the range of 800 °C to 500 °C. This leads to inadequate estimation results, as the thermal arrest caused by the microstructural transformation in this case is not considered. In this work the usage of the well-proven cooling time concept t8/5 is analyzed using high strength fine grained structural steels and suitable welding filler wires during gas metal arc and submerged arc welding processes. The results are discussed taking into account the microstructure and the transformation behavior. Based on the experimental work, an improved concept is presented.

Investigations on the Mechanical Properties and Formability of Friction Stir Welded Tailored Blanks

2007 ◽  
Vol 344 ◽  
pp. 143-150 ◽  
Author(s):  
Gianluca Buffa ◽  
Livan Fratini ◽  
Marion Merklein ◽  
Detlev Staud
Keyword(s):  
Mechanical Properties ◽  
Stress Condition ◽  
Research Effort ◽  
High Strength Steels ◽  
High Strength ◽  
Tensile Tests ◽  
Friction Stir ◽  
Tailored Blanks ◽  
Sheet Stamping ◽  
Wide Range

Tight competition characterizing automotive industries in the last decades has determined a strong research effort aimed to improve utilized processes and materials in sheet stamping. As far as the latter are regarded light weight alloys, high strength steels and tailored blanks have been increasingly utilized with the aim to reduce parts weight and fuel consumptions. In the paper the mechanical properties and formability of tailored welded blanks made of a precipitation hardenable aluminum alloy but with different sheet thicknesses, have been investigated: both laser welding and friction stir welding have been developed to obtain the tailored blanks. For both welding operations a wide range of the thickness ratios has been considered. The formability of the obtained blanks has been characterized through tensile tests and cup deep drawing tests, in order to show the formability in dependency of the stress condition; what is more mechanical and metallurgical investigations have been made on the welded joints.

Metallurgical Study of Friction Stir Welded High Strength Steels for Shipbuilding

2014 ◽  
Vol 783-786 ◽  
pp. 2798-2803 ◽  
Author(s):  
Marion Allart ◽  
Alexandre Benoit ◽  
Pascal Paillard ◽  
Guillaume Rückert ◽  
Myriam Chargy
Keyword(s):  
Cubic Boron Nitride ◽  
High Strength Steels ◽  
High Strength ◽  
High Yield ◽  
Friction Stir ◽  
Polycrystalline Cubic Boron Nitride ◽  
Recent Developments ◽  
Metallurgical Study ◽  
Welding Processes ◽  
Pcbn Tools

Friction Stir Welding (FSW) is one of the most recent welding processes, invented in 1991 by The Welding Institute. Recent developments, mainly using polycrystalline cubic boron nitride (PCBN) tools, broaden the range of use of FSW to harder materials, like steels. Our study focused on the assembly of high yield strength steels for naval applications by FSW, and its consequences on the metallurgical properties. The main objectivewas to analyze the metallurgical transformations occurring during welding. Welding tests were conducted on three steels: 80HLES, S690QL and DH36. For each welded sample, macrographs, micrographs and micro-hardness maps were performed to characterize the variation of microstructures through the weld.

Some Fracture Mechanics Correlations

1968 ◽  
Vol 10 (4) ◽  
pp. 329-336
Author(s):  
L. P. Pook
Keyword(s):  
Mechanical Properties ◽  
Fracture Mechanics ◽  
Tensile Test ◽  
High Strength Steels ◽  
High Strength ◽  
Gauge Length ◽  
Published Data ◽  
Square Root ◽  
Beryllium Copper ◽  
Reduction Of Area

The results of tests on two high-strength steels, beryllium copper and perspex, together with some published data on high-strength steels were examined to see whether there was any relationship between the fracture mechanics parameter K1C and conventional mechanical properties. It was found that for steels and beryllium copper a correlation appeared to exist between K1C and the zero gauge length strain (= Z/(1 - Z) where Z is the reduction of area measured in a tensile test). It was also found that for constant, K1C was proportional to the square root of Young's modulus. The correlation band for steels was too wide for K1C to be estimated accurately from.

Influence of Tool Rotational Speed on the Mechanical Properties of Friction Stir Welded Al-Cu-Li Alloy

2016 ◽  
Vol 857 ◽  
pp. 228-231
Author(s):  
Ho Sung Lee ◽  
Ye Rim Lee ◽  
Kyung Ju Min
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Space Shuttle ◽  
Welding Process ◽  
High Strength ◽  
Fusion Welding ◽  
Welding Parameters ◽  
Friction Stir ◽  
Mechanical And Microstructural Properties ◽  
Tool Rotation

Aluminum-Lithium alloys have been found to exhibit superior mechanical properties as compared to the conventional aerospace aluminum alloys in terms of high strength, high modulus, low density, good corrosion resistance and fracture toughness at cryogenic temperatures. Even though they do not form low-melting eutectics during fusion welding, there are still problems like porosity, solidification cracking, and loss of lithium. This is why solid state friction stir welding is important in this alloy. It is known that using Al-Cu-Li alloy and friction stir welding to super lightweight external tank for space shuttle, significant weight reduction has been achieved. The objective of this paper is to investigate the effect of friction stir tool rotation speed on mechanical and microstructural properties of Al-Cu-Li alloy. The plates were joined with friction stir welding process using different tool rotation speeds (300-800 rpm) and welding speeds (120-420 mm/min), which are the two prime welding parameters in this process.

scholarly journals Thermal Diffusivity of Traditional and Innovative Sheet Steels

2010 ◽  
Vol 297-301 ◽  
pp. 893-898
Author(s):  
Elena Campagnoli ◽  
Paolo Matteis ◽  
Giovanni M.M. Mortarino ◽  
Giorgio Scavino
Keyword(s):  
Thermal Diffusivity ◽  
Deep Drawing ◽  
Process Model ◽  
Twip Steel ◽  
Welding Process ◽  
High Strength Steels ◽  
High Strength ◽  
Carbon Steels ◽  
Low Carbon ◽  
Low Carbon Steels

The low carbon steels, used for the production of car bodies by deep drawing, are gradually substituted by high strength steels for vehicle weight reduction. The drawn car body components are joined by welding and the welded points undergo a reduction of the local tensile strength. In developing an accurate welding process model, able to optimized process parameters and to predict the final local microstructure, a significant improvement can be given by the knowledge of the welded steels thermal diffusivity at different temperatures. The laser-flash method has been used to compare the thermal diffusivity of two traditional deep drawing steels, two high strength steels already in common usage, i.e. a Dual Phase (DP) steel and a TRansformation Induced Plasticity (TRIP) steel, and one experimental high-Mn austenitic TWIP (Twinning Induced Plasticity) steel. The low carbon steels, at low temperatures, have a thermal diffusivity that is 4-5 times larger than the TWIP steel. Their thermal diffusivity decreases by increasing temperature while the TWIP steel shows an opposite behaviour, albeit with a lesser slope, so that above 700°C the TWIP thermal diffusivity is larger. The different behaviour of the TWIP steel in respect to the ferritic deep drawing steels arises from its non ferro-magnetic austenitic structure. The DP and TRIP steels show intermediate values, their diffusivity being lower than that of the traditional deep drawing steels; this latter fact probably arises from their higher alloy content and more complex microstructure.

scholarly journals The Assessment of Selected Properties of Welded Joints in High-Strength Steels

2020 ◽  
pp. 73-79
Author(s):  
Lechosław Tuz
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Welded Joints ◽  
Heat Input ◽  
Structural Changes ◽  
High Strength Steels ◽  
High Strength ◽  
High Quality ◽  
Treatment Processes ◽  
Welding Processes

The use of technologically advanced structural materials entails the necessity of adjusting typical welding processes to special requirements resulting from the limited weldability of certain material groups. Difficulties obtaining high-quality joints may be the consequence of deteriorated mechanical properties and structural changes in materials (beyond requirements of related standards). One of the aforementioned materials is steel characterised by a guaranteed yield point of 1300 MPa, where high strength is obtained through the addition of slight amounts of carbide-forming elements and the application of complex heat treatment processes. A heat input during welding may worsen the aforesaid properties not only in the weld but also in the adjacent material. The tests discussed in the article revealed that the crucial area was that heated below a temperature of 600°C, where the hardness of the material decreased from approximately 520 HV to 330 HV.

scholarly journals Control of mechanical properties of high-strength steels through optimized welding processes

2016 ◽  
Vol 2016 (7) ◽  
pp. 32-36
Author(s):  
M. Fiedler ◽  
◽  
A. Plozner ◽  
B. Rutzinger ◽  
W. Scherleitner ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Strength Steels ◽  
High Strength ◽  
Welding Processes

scholarly journals A Multi-attribute Control Chart for Monitoring Friction Stir Welding Process Considering Small Sample Sizes

2018 ◽  
Vol 23 (4) ◽  
pp. 474-484
Author(s):  
Esmeralda Ramírez-Méndez ◽  
Mario Cantu-Sifuentes ◽  
David Salvador González-González ◽  
Argelia Fabiola Miranda-Pérez ◽  
Rolando Javier Praga-Alejo
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Control Chart ◽  
Welding Process ◽  
Small Sample ◽  
Sample Sizes ◽  
Process Data ◽  
Friction Stir ◽  
Small Sample Sizes ◽  
Welding Processes

Abstract Often, welding processes used in the industry affect the mechanical properties of materials and quality of a manufactured product. There is, however, an alternative process named Friction Stir Welding (FSW), which is an solid state welding process developed to weld light alloys without compromising their mechanical properties. It is of interest to monitor the performance of FSW process to detect loss of quality. In practice, superficial and internal defects can be found; they can be identified through simple visual inspection and through visual recognition on destructive testing respectively, both procedures represent inspection by attributes. Therefore a multi-attribute control chart is assessed to monitor the process. Commonly, multi-attribute control charts involve high sampling rates to ensure accurate monitoring. In this paper, a multi-attribute control chart is proposed, considering the use of empirical control limits, instead of the theoretical ones, in order to improve its accuracy and lessen the small sample sizes effect. The performance of proposed approaches is analyzed by means of Monte Carlo simulation. The results suggest that the performance of the empirical designs is better than the theoretical ones in all tested cases. Finally, the results of monitoring FSW process data are detailed.

Solid-state joining of aluminum to titanium: A review

2021 ◽  
pp. 146442072110108
Author(s):  
Vijay S Gadakh ◽  
Vishvesh J Badheka ◽  
Amrut S Mulay
Keyword(s):  
Mechanical Properties ◽  
Solid State ◽  
Titanium Alloys ◽  
Intermetallic Compounds ◽  
Welding Process ◽  
High Strength ◽  
Weld Interface ◽  
Fusion Welding ◽  
Cp Ti ◽  
Welding Processes

The dissimilar material joining of aluminum and titanium alloys is recognized as a challenge due to the significant differences in the physical, chemical, and metallurgical properties of these alloys, where the increasing demands for high strength and lightweight alloys in aerospace, defense, and automotive industries. Joining these two alloys using the conventional fusion techniques produces commercially unacceptable sound joints due to irregular, complex weld pool shapes, cracking and low strength, high residual stresses, cracks, and microporosity, and the brittle intermetallic compounds formation leads to poor formability or inferior mechanical properties. The formation of intermetallic compounds is inevitable but it is less severe in solid-state than in the fusion welding process. Hence, this article reviews on aluminum–titanium joining using different solid-state and hybrid joining processes with emphasis on the effect of process parameters of the different processes on the weld microstructure, mechanical properties along with the type of intermetallic compounds and defects formed at the weld interface. Among the various solid-state welding processes for aluminum–titanium joining, the following grades of aluminum and titanium alloys were employed such as cp Ti, Ti6Al4V, cp Al, AA1xxx, AA 2xxx, AA5xxx, AA6xxx, AA7xxx, out of which Ti6Al4V and AA6xxx alloys are the most common combination.

Sign in / Sign up

Export Citation Format

Share Document