scholarly journals Leachability and physical stability of solidified and stabilized pyrite cinder sludge from dye effluent treatment

2015 ◽  
Vol 69 (3) ◽  
pp. 231-239 ◽  
Author(s):  
Djurdja Kerkez ◽  
Milena Becelic-Tomin ◽  
Milena Dalmacija ◽  
Dragana Tomasevic ◽  
Srdjan Roncevic ◽  
...  
Keyword(s):  
Toxic Metals ◽  
Physical Stability ◽  
Single Step ◽  
Effluent Treatment ◽  
Test Results ◽  
Pyrite Cinder ◽  
X Ray Diffraction ◽  
Heterogeneous Fenton ◽  
X Ray ◽  
Clay Materials

This work is concerned with exploring the possibilities of using solidification/stabilization (S/S) treatment for toxic sludge generated in dye effluent treatment, when pyrite cinder is used as catalytic iron source in the modified heterogeneous Fenton process. S/S treatment was performed by using different clay materials (kaolin, bentonite and native clay from the territory of Vojvodina) and fly ash in order to immobilize toxic metals and arsenic presented in sludge. For the evaluation of the extraction potential of toxic metals and the effectiveness of the S/S treatment applied, four single-step leaching tests were performed. Leaching test results indicated that all applied S/S treatments were effective in immobilizing toxic metals and arsenic presented in sludge. X-ray diffraction analysis confirmed the formation of pozzolanic products, and compressive strength measurement proved the treatment efficacy. It can be concluded that the S/S technique has significant potential for solving the problem of hazardous industrial waste and its safe disposal.

scholarly journals Assessing the possibility of solidification and stabilization of pyrite cinder by using quicklime and fly ash

2020 ◽  
Vol 11 (2) ◽  
Author(s):  
Đurđa Kerkez ◽  
Dragana Tomašević Pilipović ◽  
Milena Bečelić‐Tomin ◽  
Nataša Slijepčević ◽  
Dunja Rađenović ◽  
...  
Keyword(s):  
Fly Ash ◽  
Low Cost ◽  
Test Results ◽  
Pyrite Cinder ◽  
X Ray Diffraction ◽  
Leaching Behavior ◽  
X Ray ◽  
Acidic Solutions ◽  
Lead And Zinc ◽  
Very High

The aim of this study was to determine the possibility of using two low-cost binders,quicklime and fly ash for the solidification/stabilization (S/S) of pyrite cinder.Pyrite cinder, used in this study, represents a remnant from sulfuric acid productionin fertilizer factory IHP “Prahovo” A.D. (Serbia), and has a very high toxicmetal content. High contents and leachability of copper, lead and zinc make thiswaste material hazardous, representing an extraordinary risk to the environment.In order to determine the leaching behavior of the S/S mixtures, four single-stepleaching tests were performed, each one having a different sort of leaching fluid(deionized water, inorganic and organic acidic solutions). X-ray diffraction (XRD),scanning electron microscope (SEM) and energy dispersive X-ray analyzer (EDS)were implemented to elucidate the mechanisms responsible for immobilization ofCu, Pb and Zn. Overall, the test results indicated that S/S treatment using bothquicklime and fly ash was effective in immobilizing these metals, especially whenthere is a higher share of binder present. Treated waste can be safe for disposal andeven considered for “controlled utilization”. Furthermore, the use of fly ash for S/Streatment of pyrite cinder solves the disposal problems of two waste types, as it alsorepresents a secondary industrial product.

Transient liquid phase bonding of Cu and Al using metallic particles interlayers

2021 ◽  
pp. 095440542098823
Author(s):  
Alireza Zaheri ◽  
Mohammadreza Farahani ◽  
Alireza Sadeghi ◽  
Naser Souri
Keyword(s):  
Liquid Phase ◽  
Mechanical Test ◽  
Transient Liquid Phase ◽  
Transient Liquid Phase Bonding ◽  
Joint Interface ◽  
Test Results ◽  
X Ray Diffraction ◽  
X Ray ◽  
Metallic Particles ◽  
Powder Interlayer

The bonding strength, and microstructures of Cu and Al couples using metallic powders as interlayer during transient liquid phase bonding (TLP bonding) were investigated. The interfacial morphologies and microstructures were studied by scanning electron microscopy equipped with energy dispersive X-ray spectroscopy, and X-ray diffraction. First, to explore the optimum bonding time and temperature, nine samples were bonded without interlayers in a vacuum condition. Mechanical test results indicated that bonding at 560°C in 20 min returns the highest bond strength (84% of Al). This bonding condition was used to join ten samples with powder interlayers. Powders were prepared by mixing different combinations of Cu, Al (+Fe nanoparticles) and Zn. In the bonding zone, different Cu9Al4, CuAl, and CuAl2 intermetallic co-precipitate. The strongest bonding is formed in the sample with the 70Al (+Fe)-30Cu powder interlayer. Powder interlayers present thinner and more uniform intermetallic layers at the joint interface.

scholarly journals Laser-Induced Deposition of Plasmonic Ag and Pt Nanoparticles, and Periodic Arrays

Materials ◽  
2020 ◽  
Vol 14 (1) ◽  
pp. 10
Author(s):  
Daria V. Mamonova ◽  
Anna A. Vasileva ◽  
Yuri V. Petrov ◽  
Denis V. Danilov ◽  
Ilya E. Kolesnikov ◽  
...  
Keyword(s):  
Substrate Surface ◽  
Pt Nanoparticles ◽  
Single Step ◽  
X Ray Diffraction ◽  
Ag Nps ◽  
X Ray ◽  
Periodic Arrays ◽  
Potential Applications ◽  
Surface Decoration ◽  
Wide Potential

Surfaces functionalized with metal nanoparticles (NPs) are of great interest due to their wide potential applications in sensing, biomedicine, nanophotonics, etc. However, the precisely controllable decoration with plasmonic nanoparticles requires sophisticated techniques that are often multistep and complex. Here, we present a laser-induced deposition (LID) approach allowing for single-step surface decoration with NPs of controllable composition, morphology, and spatial distribution. The formation of Ag, Pt, and mixed Ag-Pt nanoparticles on a substrate surface was successfully demonstrated as a result of the LID process from commercially available precursors. The deposited nanoparticles were characterized with SEM, TEM, EDX, X-ray diffraction, and UV-VIS absorption spectroscopy, which confirmed the formation of crystalline nanoparticles of Pt (3–5 nm) and Ag (ca. 100 nm) with plasmonic properties. The advantageous features of the LID process allow us to demonstrate the spatially selective deposition of plasmonic NPs in a laser interference pattern, and thereby, the formation of periodic arrays of Ag NPs forming diffraction grating

scholarly journals Intercalation of oxalate ions in the interlayer space of a layered double hydroxide for nickel ions adsorption

2016 ◽  
Vol 5 (2) ◽  
pp. 144
Author(s):  
Doungmo Giscard ◽  
Théophile Kamgaing ◽  
Ranil Clément Tonleu Temgoua ◽  
Ervice Ymele ◽  
Francis Merlin Melataguia Tchieno ◽  
...  
Keyword(s):  
Interlayer Space ◽  
X Ray Diffraction ◽  
Batch Mode ◽  
Nickel Ions ◽  
X Ray ◽  
Modified Clay ◽  
Pseudo Second Order ◽  
Oxalate Ions ◽  
Double Hydroxide ◽  
Clay Materials

In this study, sorption properties of a synthesized anionic clay were enhanced by the intercalation of oxalate ions in its interlayer space. The pristine and modified clay materials were characterized by X-ray diffraction, Fourier transform infrared spectroscopy and thermal analysis. These techniques confirmed the presence of oxalate ions in the interlayer space of the clay. The intercalated clay was then used as a matrix for the sorption in batch mode of nickel ions in aqueous solution. The influence of a number of parameters such as contact time, pH, initial concentration of the analyte and adsorbent dosage were studied. The maximum adsorption of nickel was obtained at pH 6, that is, about 90% Ni2+ removal. The adsorbent/adsorbate equilibrium follows a pseudo-second order kinetics and best matches the Langmuir model. The modified clay was shown to be efficient matrix for the sorption of nickel ions.

Facile Refluxing Synthesis of Hydroxyapatite Nanoparticles

2015 ◽  
Vol 68 (8) ◽  
pp. 1293 ◽  
Author(s):  
Pakvipar Chaopanich ◽  
Punnama Siriphannon
Keyword(s):  
Crystallite Size ◽  
Reaction Times ◽  
Single Step ◽  
Hydroxyapatite Nanoparticles ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Aqueous Mixture ◽  
Diffraction Patterns ◽  
Microscopy Images

Hydroxyapatite (HAp) nanoparticles were successfully synthesized from an aqueous mixture of Ca(NO3)2·4H2O and (NH4)2HPO4 by a facile single-step refluxing method using polystyrene sulfonate (PSS) as a template. The effects of reaction times, pH, and PSS concentration on the HAp formation were investigated. It was found that the crystalline HAp was obtained under all conditions after refluxing the precursors for 3 and 6 h. The longer refluxing time, the greater the crystallinity and the larger the crystallite size of the HAp nanoparticles. The HAp with poor crystallinity was obtained at pH 8.5; however, the well-crystallized HAp was obtained when reaction pH was increased to 9.5 and 10.5. In addition, the X-ray diffraction patterns revealed that the presence of PSS template caused the reduction of HAp crystallite size along the (002) plane from 52.6 nm of non-template HAp to 43.4 nm and 41.4 nm of HAp with 0.05 and 0.2 wt-% PSS template, respectively. Transmission electron microscopy images of the synthesized HAp revealed the rod-shaped crystals of all samples. The synthesized HAp nanoparticles were modified by l-aspartic acid (Asp) and l-arginine (Arg), having negative and positive charges, respectively. It was found that the zeta potential of HAp was significantly changed from +5.46 to –24.70 mV after modification with Asp, whereas it was +4.72 mV in the Arg-modified HAp. These results suggested that the negatively charged amino acid was preferentially adsorbed onto the synthesized HAp surface.

scholarly journals Physical Stability and Viscoelastic Properties of Co-Amorphous Ezetimibe/Simvastatin System

2019 ◽  
Vol 12 (1) ◽  
pp. 40 ◽  
Author(s):  
Justyna Knapik-Kowalczuk ◽  
Krzysztof Chmiel ◽  
Karolina Jurkiewicz ◽  
Natália Correia ◽  
Wiesław Sawicki ◽  
...  
Keyword(s):  
Elevated Temperature ◽  
Viscoelastic Properties ◽  
Room Temperature ◽  
Physical Stability ◽  
Ternary Systems ◽  
Storage Conditions ◽  
X Ray Diffraction ◽  
X Ray ◽  
Temperature Conditions ◽  
First Time

The purpose of this paper is to examine the physical stability as well as viscoelastic properties of the binary amorphous ezetimibe–simvastatin system. According to our knowledge, this is the first time that such an amorphous composition is prepared and investigated. The tendency toward re-crystallization of the amorphous ezetimibe–simvastatin system, at both standard storage and elevated temperature conditions, have been studied by means of X-ray diffraction (XRD). Our investigations have revealed that simvastatin remarkably improves the physical stability of ezetimibe, despite the fact that it works as a plasticizer. Pure amorphous ezetimibe, when stored at room temperature, begins to re-crystallize after 14 days after amorphization. On the other hand, the ezetimibe-simvastatin binary mixture (at the same storage conditions) is physically stable for at least 1 year. However, the devitrification of the binary amorphous composition was observed at elevated temperature conditions (T = 373 K). Therefore, we used a third compound to hinder the re-crystallization. Finally, both the physical stability as well as viscoelastic properties of the ternary systems containing different concentrations of the latter component have been thoroughly investigated.

Effect of nano Al2O3 coated Ag reinforced Cu matrix nanocomposites on mechanical and tribological behavior synthesis by P/M technique

2020 ◽  
Vol 54 (30) ◽  
pp. 4921-4928
Author(s):  
A Mohamed ◽  
MM Mohammed ◽  
AF Ibrahim ◽  
Omyma A El-Kady
Keyword(s):  
Wear Behavior ◽  
Composite Coatings ◽  
Microstructural Analysis ◽  
Wear Test ◽  
Test Results ◽  
X Ray Diffraction ◽  
X Ray ◽  
Average Hardness ◽  
Ag Particles ◽  
Matrix Nanocomposites

In this study, copper powder was reinforced with different weight percentages of Al2O3 particles (0, 5, 10, and 15 wt.% Al2O3 coated Ag) to produce Cu-Al2O3 composites by mechanical alloying and uniaxial cold pressing/sintering route. Electro-less deposition was used to coat Al2O3 particles with Ag. The microstructure of the consolidated samples was investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) elemental mapping. The porosity, microhardness, and wear behavior of the consolidated samples were also investigated as a function of Al2O3 content. The EDX mapping images reveal that the Al2O3 reinforcement particles were homogeneously distributed into the Cu matrix. Microstructural analysis shows that the addition of Al2O3 coated Ag particles improves density of the composites coating. SEM micrographs result shows that slight porosities exist in the composites produced. Furthermore, the average hardness of the composite coatings varies from 72.3 to 187.6 HV as Al2O3 content increases from 0 to 15 wt.%. The wear test results showed that the composite with higher Al2O3 content 15 wt.% showed the best wear resistance.

A Novel Approach to Unzipped Tubes Synthesis Using Sulfanilic Acid as the Backbone Amino Acid

2019 ◽  
Vol 57 ◽  
pp. 17-30
Author(s):  
Christopher Narh ◽  
Charles Frimpong ◽  
Qu Fu Wei
Keyword(s):  
Differential Scanning Calorimetry ◽  
Bond Formation ◽  
Sulfanilic Acid ◽  
Test Results ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Torsion Angles ◽  
X Ray ◽  
Novel Approach ◽  
Hydrophobic Peptide

In this research, unzipped sulfanilic acid inspired hydrophobic peptide tube was synthesis by increasing the polarity of sulfanilic acid through nucleophilic attachment of aniline which then provided two reactive sites at the S-terminus. These two sites were then attached with the N-terminal of valine and alanine respectively at an intensity of 1000-1600 of 11 2θ (°). Through π-π stacking at the side chains, the opened ended peptide was linearly arranged to form the unzipped tube. Fourier transform infrared spectroscopy (FTIR) confirm the amine bond formation whiles X-ray diffraction test results confirmed D-spacing 7.36 and 4.44 corresponding 2θ (°)12 and 19.97 respectively whiles the torsion angles (Ø2) conformations was between-150.5°and-169.2° and-2 between-129.0° and-150.6°. The Thermogravimetric analysis result showed an increase in the rigidity of the bond with an increasing intensity. Finally, Differential scanning calorimetry (DSC) test was carried out to confirm the crystallinity of the structure. Keywords: Sulfanilic acid, hydrophobic Peptide, Unzipped tubes, Nanomaterial

scholarly journals Quantitative Evaluation of Crystalline and Amorphous Phases in Clay-Based Cordierite Ceramic

Minerals ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 1122
Author(s):  
Zdeněk Klika ◽  
Marta Valášková ◽  
Lucie Bartoňová ◽  
Petra Maierová
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Chemical Analysis ◽  
Test Results ◽  
Mineral Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Amorphous Phases ◽  
Cordierite Ceramic ◽  
Scanning Electron

An innovative chemical quantitative mineral analysis (CQMA) was successfully tested on a cordierite-based clay ceramic sample to quantify crystalline and amorphous components. The accuracy of this method was demonstrated on an added module to the CQMA program that used oxide formulas of amorphous phases obtained by energy dispersive X-ray spectroscopy (EDS) microprobe chemical analysis. This CQMA method was tested for three variants calculated using chemical analysis, i.e., X-ray diffraction (XRD) identification of crystalline (cordierite and enstatite) and amorphous phases by scanning electron microscopy (SEM)/EDS texture and microanalyses. The test results from CQMA suggest their application possibilities as well as the limits of their utilization.

Characterization of clays and the technology of Roman ceramics production

Clay Minerals ◽  
2018 ◽  
Vol 53 (3) ◽  
pp. 413-429 ◽  
Author(s):  
Letizia Ceccarelli ◽  
Maurizio Pietro Bellotto ◽  
Marco Caruso ◽  
Cinzia Cristiani ◽  
Giovanni Dotelli ◽  
...  
Keyword(s):  
Fourier Transform ◽  
First Century ◽  
X Ray Diffraction ◽  
Local Clay ◽  
X Ray ◽  
Ancient Technology ◽  
Differential Thermogravimetric Analysis ◽  
The Rich ◽  
Clay Materials

ABSTRACTThe recent discovery of a Roman ceramics manufacturing workshop at Montelabate (Perugia, Italy), in use from the first century BC until the late-fourth to fifth centuries AD, offers a unique opportunity to study the technical processes for producing Roman amphorae. Ancient and modern clays were sampled and analysed; they do not differ significantly, supporting the hypothesis of the exploitation of the rich local clay source that allowed a continuity of production. Characterization of the clays was performed using geotechnical methods (Atterberg limits and size distribution) and by thermogravimetric and differential thermogravimetric analysis, Fourier-transform infrared spectroscopy, X-ray diffraction and X-ray fluorescence analyses. The material was suitable for pottery making with the addition of calcite and quartz sand temper. Production waste and discarded materials as well as good-quality products were also analysed with the same methodology. It is therefore possible to reconstruct the ancient technology by defining the recipe for the production of the amphorae and their firing temperature on the basis of the decomposition of clay materials and the presence of newly formed minerals.

Sign in / Sign up

Export Citation Format

Share Document