scholarly journals Evaluation of Lagergren Kinetics Equation by Using Novel Kinetics Expression of Sorption of Zn2+ onto Horse Dung Humic Acid (HD-HA)

2018 ◽  
Vol 16 (3) ◽  
pp. 338 ◽  
Author(s):  
Bambang Rusdiarso ◽  
Rahmat Basuki ◽  
Sri Juari Santosa
Keyword(s):  
Humic Acid ◽  
Kinetic Model ◽  
Sorption Capacity ◽  
Complex Function ◽  
Freundlich Isotherm ◽  
Isotherm Model ◽  
Extraction And Purification ◽  
Langmuir Isotherm Model ◽  
Desorption Rate Constant ◽  
Kinetic Expression

Extraction and purification of humic acid from dry horse dung powder (HD-HA) was performed successfully and the purified HD-HA was then applied as sorbent to adsorb Zn2+. Extraction and purification were performed based on procedure of Stevenson (1994) under atmospheric air. Parameters investigated in this work consist of effect of medium sorption acidity, sorption rate (ka) and desorption rate constant (kd), Langmuir (monolayer) and Freundlich (multilayer) sorption capacities, and energy (E) of sorption. The ka and kd were determined according to the kinetic model of second order sorption reaching equilibrium, monolayer sorption capacity (b) and energy (E) were determined according to Langmuir isotherm model, and multilayer sorption capacity (B) was determined based on Freundlich isotherm model. Sorption of Zn2+ on purified HD-HA was maximum at pH 5.0. The novel kinetic expression resulted from proposed kinetic model has been shown to be more applicable than the commonly known Lagergren equation obtained from the pseudo-first order sorption model. The application of the equation revealed that the intercept of Lagergren equation, ln qe was more complex function of initial concentration of Zn2+ (a), Langmuir sorption capacity (b), and sorbed Zn2+ at equilibrium (xe).

scholarly journals Sorption of Ni(II) and Cr(III) ions by the Chironomus yoshimatsui larvae from wastewater

2018 ◽  
Vol 15 (1) ◽  
pp. 6062-6069
Author(s):  
Keon Sang Ryoo
Keyword(s):  
Freundlich Isotherm ◽  
Sorption Kinetics ◽  
Isotherm Model ◽  
Sorption Data ◽  
First Order ◽  
Batch System ◽  
Survival Capacity ◽  
Langmuir Isotherm Model ◽  
Treatment Technologies ◽  
Kinetics Of

In this study, Chironomus yoshimatsui larvae were applied to remove Ni(II) and Cr(III) ions from wastewater. The sorption studies were carried out using laboratory-reared C. y. larvae. It was found that C. y. larvae are very susceptible to Cr(III) as compared to Ni(II). The survival capacity of C. y. larvae was sharply reduced when exposed to even low Cr(III) concentration. Sorption isotherm and kinetics of C. y. larvae for Ni(II) were determined by means of controlled experiments in a batch system. It was observed that sorpyion efficiency of Ni(II) was largely concentration dependent and more effective at lower concentration. At each equilibrium, Ni(II) was removed up to roughly 44∼80 %. Sorption data were better fitted to the Langmuir isotherm model because of its correlation coefficient R2 value greater than that of the Freundlich isotherm model. The sorption kinetics by C. y. larvae for Ni(II) was well described a pseudo-first-order rate expression. C. y. larvae have enormous potential for application in wastewater treatment technologies because they are widespread and abundant all around the world and can be easily kept in culture.

Synthesis, Characterization and Adsorption Property of Expanded Graphite/Conducting Polymer Composite

2011 ◽  
Vol 322 ◽  
pp. 93-97 ◽  
Author(s):  
Min Cong Zhu ◽  
Wei Qi ◽  
Yan Jie Mao ◽  
Yin Hu ◽  
Xin Qing ◽  
...  
Keyword(s):  
Adsorption Property ◽  
Expanded Graphite ◽  
Freundlich Isotherm ◽  
Reactive Dye ◽  
Isotherm Model ◽  
Freundlich Isotherms ◽  
Pani Composite ◽  
Equilibrium Data ◽  
Langmuir Isotherm Model ◽  
Ir Analysis

In the present work, expanded graphite (EG) was prepared by microwave irradiation. Then, the expanded graphite/polyaniline (EG/PANi) composite was synthesized in the typical method. The samples of EG and EG/PANi were characterized by SEM and IR analysis techniques. Adsorption property of EG/PANi composite for removing the dye, reactive brilliant red K-2BP, from aqueous solution was investigated. The effects of initial dye concentration and contact time, pH, sorbent dosage on the adsorption process were studied. Experimental data were modelled by Langmuir and Freundlich isotherms. Langmuir isotherm model fitted well the equilibrium data for EG/PANi composite comparing to the Freundlich isotherm model. The uptake capacity of EG/PANi for K-2BP was found to be 1.03047 mg/g. The results indicated that EG/PANi composite is not an ideal sorbent used for reactive dye removal.

scholarly journals Adsorption Properties of Ni(II) by D301R Anion Exchange Resin

2014 ◽  
Vol 2014 ◽  
pp. 1-5
Author(s):  
Song Xiuling ◽  
Du Huipu ◽  
Liu Shijun ◽  
Qian Hui
Keyword(s):  
Anion Exchange ◽  
Exchange Resin ◽  
Anion Exchange Resin ◽  
Freundlich Isotherm ◽  
Isotherm Model ◽  
Bending Vibration ◽  
Freundlich Model ◽  
Diffusion Controlled ◽  
Equilibrium Data ◽  
Langmuir Isotherm Model

The adsorption of Ni(II) with D301R resin was investigated in this paper. The results showed that the saturated extent of adsorption Ni(II) by the resin was 84.3 mg/g. The equilibrium data of Ni(II) sorption was better described by Langmuir isotherm model (r2=0.994) while that of Ni(II) sorption also fitted in Freundlich isotherm model within the experimental concentration range. The amount of the constant (q0) of Ni(II) under 298 K in Langmuir model was 76.92 mg/g, which was close to the experimental results. The constant n was within 2–10 in Freundlich model; it was shown that adsorption of Ni(II) by the resin was easy to take place. The uptake kinetics followed the Lagergren pseudo-first-order rate equation (r2=0.9813). The particle diffusion controlled the adsorption process of Ni(II). The coefficient of the intraparticle diffusion increased with the increase of the pH values and the concentration of Ni(II) in aqueous solution. There was a drop of 20.1 cm−1for the bending vibration frequency of N–H bond. Results showed that the adsorption of Ni(II) by D301R anion exchange resin was the surface complexation through the infrared spectrum analysis.

The Adsorption Properties of Ciprofloxacin by KMnO4 Modified Durio zibethinus Murr Shells

2015 ◽  
Vol 1104 ◽  
pp. 111-117
Author(s):  
Wei Mei Shi ◽  
Ye Chun Ding ◽  
Long Huo Wu
Keyword(s):  
Linear Regression Analysis ◽  
Thermodynamic Characteristics ◽  
Freundlich Isotherm ◽  
Isotherm Model ◽  
Multilayer Adsorption ◽  
Durio Zibethinus ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Equilibrium Process ◽  
Kinetics Of

Through the experiment of Ciprofloxacin (CIP) adsorption by KMnO4modifiedDurio zibethinusMurr Shell (KDS), the best condition, adsorption kinetics and thermodynamic characteristics were studied. The isotherm parameters were estimated by linear regression analysis with Langmuir isotherm model, Temkin isotherm and Freundlich isotherm model. The equilibrium process was described well by the Freundlich isotherm model, which indicated that the adsorption thermodynamics of CIP on KDS is a multilayer adsorption process．The kinetics of the interactions showed better agreement with the pseudo-second-order model (R2=0.9999). This study demonstrated that KDS could be used for the removal of CIP in water treatment.

Adsorption of Toluene Using Low Cost Adsorbent

2012 ◽  
Author(s):  
Bassim H. Hameed ◽  
Abdul Rahman Mohamed ◽  
Hui Ying Chong
Keyword(s):  
Experimental Data ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Langmuir Model ◽  
Isotherm Model ◽  
Isotherm Models ◽  
Batch System ◽  
Key Words Toluene ◽  
Langmuir Isotherm Model ◽  
Langmuir And Freundlich Models

Kertas kerja ini membincangkan tentang kecekapan penjerap yang lebih murah, iaitu tayar getah terbuang (DRT), dalam menyingkirkan toluena daripada fasa akuas. Penjerapan toluena pada tayar getah terbuang dikaji menggunakan sistem berkelompok pada suhu 25°C dan 30°C. Daripada kajian ini, didapati toluena dapat disingkirkan sehingga 70% dengan menggunakan julat kepekatan awalan antara 50 mg/l hingga 300 mg/l. Dengan menggunakan model keseimbangan terlelurus, iaitu model Langmuir dan Freundlich, keupayaan penjerapan maksimum dapat ditentukan. Daripada data eksperimen, terbukti bahawa walaupun kedua–dua model isoterma Langmuir dan Freundlich boleh menjelaskan data isoterma, tetapi penjerapan toluena pada DRT dapat ditunjukkan dengan lebih baik oleh isoterma Freudlich. Bagi nilai K Freundlich, keupayaan penjerapan ialah 6.6374 mg/l dan 7.7535 mg/l, pada suhu 25°C dan 30°C. Nilai eksponen n Freudlich adalah lebih daripada satu untuk kedua–dua suhu. Kata kunci: Toluena, penjerapan, isoterma, tayar getah terbuang, model isoterma Langmuir, model isoterma Freundlich This paper discusses the effectiveness of a less expensive adsorbent, a discarded rubber tyre (DRT) in removing toluene from aqueuos phase. Adsorption of toluene on a DRT has been studied by using batch system at 25 and 30°C. It was found that up to 70% of toluene was removed for the range of toluene initial concentrations studied between 50–300 mg/l. Using linearized forms of equilibrium models, namely Langmuir and Freundlich models, the maximum adsorptive capacities were determined. It was evident from the experimental data that, although both Langmuir and Freundlich isotherm models could describe the isotherm data, the adsorption of toluene on a DRT was described well by the Freundlich isotherm. For Freundlich K values, sorption capacities were 6.6374 and 7.7535 mg/l at 25 and 30°C, respectively. The values of Freundlich exponent n were greater than one for both temperatures. Key words: Toluene, adsoprtion, isotherms, discarded rubber tyre, Langmuir isotherm model, Freundlich isotherm model

Thermodynamic Studies for Adsorption of Cd2+ and Pb2+ from Waster Water on Modified Walnut Shell

2015 ◽  
Vol 737 ◽  
pp. 622-626
Author(s):  
Shao Hua He ◽  
Dan Wang ◽  
Qing Qiu Kong ◽  
Xi Wu
Keyword(s):  
Freundlich Isotherm ◽  
Isotherm Model ◽  
Walnut Shell ◽  
Isotherm Models ◽  
Model Parameters ◽  
Maximum Adsorption Capacity ◽  
Adsorption Data ◽  
Batch Technique ◽  
Adsorption Processes ◽  
Langmuir Isotherm Model

The adsorption isothermal curve and thermodynamic adsorption of Cd2+ and Pb2+ on modified walnut shell from waster water were investigated using batch technique. The equilibrium adsorption data are fitted to Langmuir and Freundlich isotherm models and the model parameters are evaluated. The Langmuir isotherm model shows a better fit to adsorption data than the Freundlich isotherm model for the sorption of Cd2+ and Pb2+ on modified walnut shell. The maximum adsorption capacity of Cd2+ and Pb2+ by modified walnut shell is found to be 32.68 mg·g-1 and 84.75 mg·g-1 at 298K temperature, respectively. The adsorption processes of Cd2+ and Pb2+ has feasibility and spontaneous nature. Thermodynamic parameters depict the endothermic nature of sorption and the process is spontaneous and favorable.

scholarly journals Hydrazinolyzed cellulose-g-polymethyl acrylate as adsorbent for efficient removal of Cd(II) and Pb(II) ions from aqueous solution

2016 ◽  
Vol 75 (5) ◽  
pp. 1051-1058 ◽  
Author(s):  
Qiujin Jia ◽  
Wanting Zhang ◽  
Dongping Li ◽  
Yulong Liu ◽  
Yuju Che ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Physical Adsorption ◽  
Freundlich Isotherm ◽  
Isotherm Model ◽  
Initial Ph ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Adsorption Desorption ◽  
Efficient Adsorbent

Hydrazinolyzed cellulose-graft-polymethyl acrylate (Cell-g-PMA-HZ), an efficient adsorbent for removal of Cd(II) and Pb(II) from aqueous solution, has been prepared by ceric salt-initiated graft polymerization of methyl acrylate from microcrystalline cellulose surface and subsequent hydrazinolysis. The influences of initial pH, contact time, and temperature on adsorption capacity of Cell-g-PMA-HZ as well as adsorption equilibrium, kinetic and thermodynamic properties were examined in detail. As for Cd(II) adsorption, kinetic adsorption can be explained by pseudo-second-order, while adsorption isotherm fits well with Langmuir isotherm model, from which maximum equilibrium adsorption capacity can be derived as 235.85 mg g−1 at 28 °C. Further thermodynamic investigation indicated that adsorption of Cd(II) by adsorbent Cell-g-PMA-HZ is endothermic and spontaneous under studied conditions. On the other hand, isotherm of Pb(II) adsorption fits well with Freundlich isotherm model and is more likely to be a physical-adsorption-dominated process. Consecutive adsorption–desorption experiments showed that Cell-g-PMA-HZ is reusable with satisfactory adsorption capacity.

scholarly journals The Effectiveness of Magnetite Modified Gallic Acid Synthesized by Sonochemical Method As AuCl4- Adsorbent-Reductor

2021 ◽  
Vol 8 (3) ◽  
pp. 194-201
Author(s):  
Maya Rahmayanti ◽  
Sri Juari Santosa ◽  
Sutarno Sutarno ◽  
Astuti Paweni
Keyword(s):  
Adsorption Isotherm ◽  
Gallic Acid ◽  
Freundlich Isotherm ◽  
Kinetics Model ◽  
Isotherm Model ◽  
Sonochemical Method ◽  
Adsorption Method ◽  
Isotherm Adsorption ◽  
Langmuir Isotherm Model ◽  
Ph Range

In recent years gallic acid has been developed as an AuCl4- adsorbent-reducing agent. In this research, gallic acid was modified with magnetite by sonochemical method (GA-Fe3O4), and its effectiveness as an AuCl4- adsorbent was studied. GA-Fe3O4 was synthesized through one-stage (GA-Fe3O4-SK1) and two-stage (GA-Fe3O4-SK2) methods. The effectiveness of GA-Fe3O4 was studied through optimization studies on pH, time, kinetics, and isotherm adsorption of AuCl4-. The adsorption method used was the batch method in the pH range 2-7. While the kinetics model used was the Lagergren and Ho kinetics model. The adsorption isotherm model used was the Freundlich and Langmuir isotherm model. The results showed that the optimum pH conditions for adsorption of AuCl4- on GA-Fe3O4 occurred at pH 3. Adsorption of AuCl4- on GA-Fe3O4-SK1 and GA-Fe3O4-SK2 both followed the Ho kinetic model, while the adsorption isotherm followed the Freundlich isotherm model with values KF were 0.041 and 0.034 mol/g respectively.

scholarly journals Isolasi Kitosan Dari Tudung Jamur Merang (Vollvariella Volvaceae) Dan Aplikasinya Sebagai Absorben Logam Timbal (Pb)

2018 ◽  
Vol 6 (1) ◽  
pp. 44-50
Author(s):  
Matheis F.J.D.P. Tanasale ◽  
Adriani Bandjar ◽  
Natasya Sewit
Keyword(s):  
Experimental Data ◽  
Molecular Weight ◽  
Adsorption Capacity ◽  
Langmuir Isotherm ◽  
Freundlich Isotherm ◽  
Isotherm Model ◽  
Maximum Adsorption Capacity ◽  
Langmuir Isotherm Model ◽  
Ftir Spectrophotometry ◽  
Chitin And Chitosan

Chitosan isolated from mushroom (Vollariella volvaceae) as adsorbent of lead (Pb) metal has been done.  The isolation of chitosan was obtained 2.94% from total weight of mushroom.  Fungtional groups of chitin and chitosan were indentified by using FTIR spectrophotometry.  The chitosan had 74.66% degree of deacetylation and 2.09 x 104 g/mol viscosity molecular weight.  The experimental data of the chitosan as adsorbent for Pb metal were correlated with the Langmuir and Freundlich isotherm model.  The maximum adsorption capacity of Pb based on the Langmuir isotherm model was 2.66 mg/g.

The Kinetics and Isotherms of Adsorption of Sb(III) from Aqueous Solutions onto the Porous Biomorph-Genetic Composite of Fe2O3/Fe3O4/C with Bamboo Template

2013 ◽  
Vol 394 ◽  
pp. 8-13
Author(s):  
Zong Qiang Zhu ◽  
Shuang Cao ◽  
Wen Hui Wei ◽  
Yi Nian Zhu
Keyword(s):  
Kinetic Curve ◽  
Equilibrium Concentration ◽  
Freundlich Isotherm ◽  
Isotherm Model ◽  
Equilibrium Data ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Change Trend ◽  
Kinetics And Isotherms ◽  
Kinetics Of

Static adsorption of Sb (III) on a porous biomorph-genetic composite of Fe2O3/Fe3O4/C (PBGC-Fe/C-B) was studied. The results showed that the kinetic curve of Sb (III) adsorption by PBGC-Fe/C-B had same change trend under initial concentration of 5, 10 and 50 mg/L. The fitting and regression analysis of four kinds of kinetic model indicated that, the adsorption kinetics of Sb (III) by the PBGC-Fe/C-B well follow the pseudo-second-order model (R2>0.9999). At different reaction temperature (25 °C, 35 °C and 45 °C), the adsorption capacity of Sb (III) by PBGC-Fe/C-B both increased with increasing the solution equilibrium concentration. While it showed a declined tendency with temperature increased. The Langmuir isotherm model (R2>0.98) and the Freundlich isotherm model (R2>0.95) had both better fitted with the equilibrium data.

Sign in / Sign up

Export Citation Format

Share Document