scholarly journals Free form fabrication using the laser engineered net shaping (LENS{trademark}) process

1996 ◽  
Author(s):  
D.M. Keicher ◽  
J.A. Romero ◽  
C.L. Atwood ◽  
M.L. Griffith ◽  
F.P. Jeantette ◽  
...  
Keyword(s):  
Free Form ◽  
Laser Engineered Net Shaping ◽  
Net Shaping

ESTUDO DA VIABILIADE DA MANUFATURA ADITIVA DIRETA DE MULITA POR LASER ENGINEERED NET SHAPING (LENS)

2021 ◽  
Author(s):  
Thiago Azevedo ◽  
Italo Leite de Camargo ◽  
Johan sebastian Grass Nunez ◽  
Fábio Mariani ◽  
Reginaldo Coelho ◽  
...  
Keyword(s):  
Laser Engineered Net Shaping ◽  
Net Shaping

Microstructure and mechanical property of TiB reinforced Ti matrix composites fabricated by ultrasonic vibration-assisted laser engineered net shaping

2019 ◽  
Vol 25 (3) ◽  
pp. 581-591 ◽  
Author(s):  
Fuda Ning ◽  
Yingbin Hu ◽  
Weilong Cong
Keyword(s):  
Ultrasonic Vibration ◽  
Acoustic Streaming ◽  
Nonlinear Effects ◽  
Small Variation ◽  
Microstructural Characterization ◽  
Matrix Composites ◽  
Heterogeneous Distribution ◽  
Content Type ◽  
Laser Engineered Net Shaping ◽  
Net Shaping

Purpose The purpose of this paper is to identify if the implementation of ultrasonic vibration in laser engineered net shaping (LENS) process can help to reduce internal weaknesses such as porosity, coarse primary TiB whisker and heterogeneous distribution of TiB reinforcement in the LENS-fabricated TiB reinforced Ti matrix composites (TiB-TMC) parts. Design/methodology/approach An experimental investigation is performed to achieve the results for comparative studies under different fabrication conditions through quantitative data analysis. An approach of microstructural characterization and mechanical testing is conducted to obtain the output attributes. In addition, the theoretical analysis of the physics of ultrasonic vibration in the melting materials is presented to explain the influences of ultrasonic vibration on the microstructural evolution occurred in the part fabrication. Findings Because of the nonlinear effects of acoustic streaming and cavitation induced by ultrasonic vibration, porosity is significantly reduced and a relatively small variation of pore sizes is achieved. Ultrasonic vibration also causes the formation of smaller TiB whiskers that distribute along grain boundaries with a homogeneous dispersion. Additionally, a quasi-continuous network (QCN) microstructure is considerably finer than that produced by LENS process without ultrasonic vibration. The refinements of both reinforcing TiB whiskers and QCN microstructural grains further improve the microhardness of TiB-TMC parts. Originality/value The novel ultrasonic vibration-assisted (UV-A) LENS process of TiB-TMC is conducted in this work for the first time to improve the process performance and part quality.

scholarly journals The Influence of Layer Thickness on the Microstructure and Mechanical Properties of M300 Maraging Steel Additively Manufactured by LENS® Technology

Materials ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 603
Author(s):  
Natalia Rońda ◽  
Krzysztof Grzelak ◽  
Marek Polański ◽  
Julita Dworecka-Wójcik
Keyword(s):  
Mechanical Properties ◽  
Layer Thickness ◽  
Maraging Steel ◽  
Structural Integrity ◽  
Tensile Tests ◽  
Dendritic Microstructure ◽  
Fine Grained ◽  
Laser Engineered Net Shaping ◽  
Microstructure And Mechanical Properties ◽  
Net Shaping

This work investigates the effect of layer thickness on the microstructure and mechanical properties of M300 maraging steel produced by Laser Engineered Net Shaping (LENS®) technique. The microstructure was characterized using light microscopy (LM) and scanning electron microscopy (SEM). The mechanical properties were characterized by tensile tests and microhardness measurements. The porosity and mechanical properties were found to be highly dependent on the layer thickness. Increasing the layer thickness increased the porosity of the manufactured parts while degrading their mechanical properties. Moreover, etched samples revealed a fine cellular dendritic microstructure; decreasing the layer thickness caused the microstructure to become fine-grained. Tests showed that for samples manufactured with the chosen laser power, a layer thickness of more than 0.75 mm is too high to maintain the structural integrity of the deposited material.

Ultrasonic Vibration-Assisted Laser Engineered Net Shaping of Inconel 718 Parts: Microstructural and Mechanical Characterization

2018 ◽  
Vol 140 (6) ◽  
Author(s):  
Fuda Ning ◽  
Yingbin Hu ◽  
Zhichao Liu ◽  
Xinlin Wang ◽  
Yuzhou Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Ultrasonic Vibration ◽  
Inconel 718 ◽  
High Efficiency ◽  
Experimental Investigations ◽  
Laser Engineered Net Shaping ◽  
Average Grain Size ◽  
Fabrication Defects ◽  
Heterogeneous Microstructures ◽  
Net Shaping

Laser engineered net shaping (LENS) has become a promising technology in direct manufacturing or repairing of high-performance metal parts. Investigations on LENS manufacturing of Inconel 718 (IN718) parts have been conducted for potential applications in the aircraft turbine component manufacturing or repairing. Fabrication defects, such as pores and heterogeneous microstructures, are inevitably induced in the parts, affecting part qualities and mechanical properties. Therefore, it is necessary to investigate a high-efficiency LENS process for the high-quality IN718 part fabrication. Ultrasonic vibration has been implemented into various melting material solidification processes for part performance improvements. However, there is a lack of studies on the utilization of ultrasonic vibration in LENS process for IN718 part manufacturing. In this paper, ultrasonic vibration-assisted (UV-A) LENS process is, thus, proposed to fabricate IN718 parts for the potential reduction of fabrication defects. Experimental investigations are conducted to study the effects of ultrasonic vibration on microstructures and mechanical properties of LENS-fabricated parts under two levels of laser power. The results showed that ultrasonic vibration could reduce the mean porosity to 0.1%, refine the microstructure with an average grain size of 5 μm, and fragment the detrimental Laves precipitated phase into small particles in a uniform distribution, thus enhancing yield strength, ultimate tensile strength (UTS), microhardness, and wear resistance of the fabricated IN718 parts.

Sign in / Sign up

Export Citation Format

Share Document